2 files changed, 374 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
index d334f81..e0dadc4 100644
--- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
+++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml

@@ -20,6 +20,7 @@ properties:
        - qcom,pm8941-wled
        - qcom,pmi8998-wled
        - qcom,pm660l-wled
+       - qcom,pm8150l-wled
 
   reg:
     maxItems: 1

@@ -28,10 +29,23 @@ properties:
     maxItems: 1
     description:
       brightness value on boot, value from 0-4095.
+      For pm8150l this value vary from 0-4095 or 0-32767
+      depending on the brightness control mode. If CABC is
+      enabled 0-4095 range is used.

+      If CABC is enabled, this is capped to 4095.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+
   label:
     maxItems: 1
     description:

@@ -124,6 +138,31 @@ properties:
       value for PM8941 from 1 to 3. Default 2
       For PMI8998 from 1 to 4.
 
+  qcom,modulator-sel:
+    maxItems: 1
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Selects the modulator used for brightness modulation.
+      Allowed values are,
+               0 - Modulator A
+               1 - Modulator B
+      If not specified, then modulator A will be used by default.
+      This property is applicable only to WLED5 peripheral.
+
+  qcom,cabc-sel:
+    maxItems: 1
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Selects the CABC pin signal used for brightness modulation.
+      Allowed values are,
+              0 - CABC disabled
+              1 - CABC 1
+              2 - CABC 2
+              3 - External signal (e.g. LPG) is used for dimming
+      This property is applicable only to WLED5 peripheral.
+
   interrupts:
     maxItems: 2
     description:

diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c
index b73f273..edbbcb2 100644
--- a/drivers/video/backlight/qcom-wled.c
+++ b/drivers/video/backlight/qcom-wled.c

@@ -19,6 +19,8 @@
 #define WLED_DEFAULT_BRIGHTNESS				2048
 #define WLED_SOFT_START_DLY_US				10000
 #define WLED3_SINK_REG_BRIGHT_MAX			0xFFF
+#define WLED5_SINK_REG_BRIGHT_MAX_12B			0xFFF
+#define WLED5_SINK_REG_BRIGHT_MAX_15B			0x7FFF
 
 /* WLED3/WLED4 control registers */
 #define WLED3_CTRL_REG_FAULT_STATUS			0x08

@@ -40,6 +42,7 @@
 
 #define WLED3_CTRL_REG_OVP				0x4d
 #define  WLED3_CTRL_REG_OVP_MASK			GENMASK(1, 0)
+#define  WLED5_CTRL_REG_OVP_MASK			GENMASK(3, 0)
 
 #define WLED3_CTRL_REG_ILIMIT				0x4e
 #define  WLED3_CTRL_REG_ILIMIT_MASK			GENMASK(2, 0)

@@ -101,6 +104,40 @@
 
 #define WLED4_SINK_REG_BRIGHT(n)			(0x57 + (n * 0x10))
 
+/* WLED5 specific sink registers */
+#define WLED5_SINK_REG_MOD_A_EN				0x50
+#define WLED5_SINK_REG_MOD_B_EN				0x60
+#define  WLED5_SINK_REG_MOD_EN_MASK			BIT(7)
+
+#define WLED5_SINK_REG_MOD_A_SRC_SEL			0x51
+#define WLED5_SINK_REG_MOD_B_SRC_SEL			0x61
+#define  WLED5_SINK_REG_MOD_SRC_SEL_HIGH		0
+#define  WLED5_SINK_REG_MOD_SRC_SEL_EXT			0x03
+#define  WLED5_SINK_REG_MOD_SRC_SEL_MASK		GENMASK(1, 0)
+
+#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL	0x52
+#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL	0x62
+#define  WLED5_SINK_REG_BRIGHTNESS_WIDTH_12B		0
+#define  WLED5_SINK_REG_BRIGHTNESS_WIDTH_15B		1
+
+#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB		0x53
+#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_MSB		0x54
+#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB		0x63
+#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_MSB		0x64
+
+#define WLED5_SINK_REG_MOD_SYNC_BIT			0x65
+#define  WLED5_SINK_REG_SYNC_MOD_A_BIT			BIT(0)
+#define  WLED5_SINK_REG_SYNC_MOD_B_BIT			BIT(1)
+#define  WLED5_SINK_REG_SYNC_MASK			GENMASK(1, 0)
+
+/* WLED5 specific per-'string' registers below */
+#define WLED5_SINK_REG_STR_FULL_SCALE_CURR(n)		(0x72 + (n * 0x10))
+
+#define WLED5_SINK_REG_STR_SRC_SEL(n)			(0x73 + (n * 0x10))
+#define  WLED5_SINK_REG_SRC_SEL_MOD_A			0
+#define  WLED5_SINK_REG_SRC_SEL_MOD_B			1
+#define  WLED5_SINK_REG_SRC_SEL_MASK			GENMASK(1, 0)
+
 struct wled_var_cfg {
 	const u32 *values;
 	u32 (*fn)(u32);

@@ -125,6 +162,8 @@ struct wled_config {
 	u32 num_strings;
 	u32 string_i_limit;
 	u32 enabled_strings[WLED_MAX_STRINGS];

 	bool cs_out_en;
 	bool ext_gen;
 	bool cabc;

@@ -164,6 +203,27 @@ struct wled {
 	int (*wled_ovp_delay)(struct wled *wled);
 };
 
+enum wled5_mod_sel {
+	MOD_A,
+	MOD_B,
+	MOD_MAX,
+};
+
+static const u8 wled5_brightness_reg[MOD_MAX] = {
+	[MOD_A] = WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB,
+	[MOD_B] = WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB,
+};
+
+static const u8 wled5_src_sel_reg[MOD_MAX] = {
+	[MOD_A] = WLED5_SINK_REG_MOD_A_SRC_SEL,
+	[MOD_B] = WLED5_SINK_REG_MOD_B_SRC_SEL,
+};
+
+static const u8 wled5_brt_wid_sel_reg[MOD_MAX] = {
+	[MOD_A] = WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL,
+	[MOD_B] = WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL,
+};
+
 static int wled3_set_brightness(struct wled *wled, u16 brightness)
 {
 	int rc, i;

@@ -182,6 +242,25 @@ static int wled3_set_brightness(struct wled *wled, u16 brightness)
 	return 0;
 }
 
+static int wled5_set_brightness(struct wled *wled, u16 brightness)
+{
+	int rc, offset;
+	u16 low_limit = wled->max_brightness * 1 / 1000;
+	u8 v[2];
+
+	/* WLED5's lower limit is 0.1% */
+	if (brightness < low_limit)
+		brightness = low_limit;
+
+	v[0] = brightness & 0xff;
+	v[1] = (brightness >> 8) & 0x7f;
+
+	offset = wled5_brightness_reg[wled->cfg.mod_sel];
+	rc = regmap_bulk_write(wled->regmap, wled->sink_addr + offset,
+			       v, 2);
+	return rc;
+}
+