fbdev: ssd1307fb: Make reset gpio devicetree property optional

Started by Jyri Sarha on Jan 12, 2017

Subsystems (5)

Show 2 more

Maintainers (10)

Show 6 more
DORMANTno replies

open the first message on its own page

Message details and related content
Make reset gpio devicetree property optional. Depending on the board
designing there may not be a dedicated gpio for resetting the
display. Without a proper reset there may be some junk in the display
memory at probe time, so in such a case the display memory is cleared
before turning it on. The devicetree binding document is also updated.

Signed-off-by: Jyri Sarha <redacted>
---
 .../devicetree/bindings/display/ssd1307fb.txt         |  4 ++--
 drivers/video/fbdev/ssd1307fb.c                       | 19 +++++++++++++------
 2 files changed, 15 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/ssd1307fb.txt b/Documentation/devicetree/bindings/display/ssd1307fb.txt
index 4aee67f..6617df6 100644
--- a/Documentation/devicetree/bindings/display/ssd1307fb.txt
+++ b/Documentation/devicetree/bindings/display/ssd1307fb.txt
@@ -8,14 +8,14 @@ Required properties:
          0x3c or 0x3d
   - pwm: Should contain the pwm to use according to the OF device tree PWM
          specification [0]. Only required for the ssd1307.
-  - reset-gpios: Should contain the GPIO used to reset the OLED display. See
-                 Documentation/devicetree/bindings/gpio/gpio.txt for details.
   - solomon,height: Height in pixel of the screen driven by the controller
   - solomon,width: Width in pixel of the screen driven by the controller
   - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is
     mapped to.
 
 Optional properties:
+  - reset-gpios: The GPIO used to reset the OLED display, if available. See
+                 Documentation/devicetree/bindings/gpio/gpio.txt for details.
   - solomon,segment-no-remap: Display needs normal (non-inverted) data column
                               to segment mapping
   - solomon,com-seq: Display uses sequential COM pin configuration
diff --git a/drivers/video/fbdev/ssd1307fb.c b/drivers/video/fbdev/ssd1307fb.c
index 8ffaaee..89372af 100644
--- a/drivers/video/fbdev/ssd1307fb.c
+++ b/drivers/video/fbdev/ssd1307fb.c
@@ -439,6 +439,10 @@ static int ssd1307fb_init(struct ssd1307fb_par *par)
 	if (ret < 0)
 		return ret;
 
+	/* Clear the screen if we could not give reset at probe time */
+	if (!par->reset)
+		ssd1307fb_update_display(par);
+
 	/* Turn on the display */
 	ret = ssd1307fb_write_cmd(par->client, SSD1307FB_DISPLAY_ON);
 	if (ret < 0)
@@ -561,7 +565,8 @@ static int ssd1307fb_probe(struct i2c_client *client,
 
 	par->device_info = of_device_get_match_data(&client->dev);
 
-	par->reset = devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
+	par->reset = devm_gpiod_get_optional(&client->dev, "reset",
+					     GPIOD_OUT_LOW);
 	if (IS_ERR(par->reset)) {
 		dev_err(&client->dev, "failed to get reset gpio: %ld\n",
 			PTR_ERR(par->reset));
@@ -645,11 +650,13 @@ static int ssd1307fb_probe(struct i2c_client *client,
 
 	i2c_set_clientdata(client, info);
 
-	/* Reset the screen */
-	gpiod_set_value(par->reset, 0);
-	udelay(4);
-	gpiod_set_value(par->reset, 1);
-	udelay(4);
+	if (par->reset) {
+		/* Reset the screen */
+		gpiod_set_value(par->reset, 0);
+		udelay(4);
+		gpiod_set_value(par->reset, 1);
+		udelay(4);
+	}
 
 	ret = ssd1307fb_init(par);
 	if (ret)
-- 
1.9.1
Keyboard shortcuts
hback out one level
jnext message in thread / next series-diff position
kprevious message in thread / previous series-diff position
ldrill in
Escclose help / fold thread tree
?toggle this help