backlight arcxcnn devicetree bindings for ArcticSand

Started by Olimpiu Dejeu on Jan 6, 2017 · 2 messages from 2 authors · Last reply Jan 9, 2017

Subsystems (3)

Maintainers (6)

Show 2 more
STALE3600d REVIEWED · 1 review, 1 by a maintainer

Status: Reviewed.

1 review trailer (1 from subsystem maintainers).

open the first message on its own page

Message details and related content
backlight: Add devicetree bindings for the Arctic Sand backlight driver
This patch provides devicetree bindings for the Arctic Sand
    driver submitted in the previous patch
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olimpiu Dejeu <redacted>
---

v2 => v3:
- Version updated to match other patch in set. No other changes.
v1 => v2:
- Version updated to match other patch in set. No other changes.

 .../bindings/leds/backlight/arcxcnn_bl.txt         | 31 ++++++++++++++++++++++
 1 file changed, 31 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
new file mode 100644
index 0000000..a7b6ff2
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
@@ -0,0 +1,33 @@
+Binding for ArcticSand arc2c0608 LED driver
+
+Required properties:
+- compatible: should be "arc,arc2c0608"
+- reg: slave address
+
+Optional properties:
+- default-brightness: brightness value on boot, value from: 0-4095
+- label: The name of the backlight device
+			See Documentation/devicetree/bindings/leds/common.txt
+- led-sources: List of enabled channels from 0 to 5.
+			See Documentation/devicetree/bindings/leds/common.txt
+
+- arc,led-config-0: setting for register ILED_CONFIG_0
+- arc,led-config-1: setting for register ILED_CONFIG_1
+- arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
+- arc,comp-config: setting for register CONFIG_COMP
+- arc,filter-config: setting for register FILTER_CONFIG
+- arc,trim-config: setting for register IMAXTUNE
+
+Note: Optional properties not specified will default to values in IC EPROM
+
+Example:
+
+arc2c0608@30 {
+	compatible = "arc,arc2c0608";
+	reg = <0x30>;
+	default-brightness = <500>;
+	label = "lcd-backlight";
+	linux,default-trigger = "backlight";
+	led-sources = <0 1 2 5>;
+};
+
-- 
2.7.4
Message details and related content
On Fri, 06 Jan 2017, Olimpiu Dejeu wrote:
quoted hunk
backlight: Add devicetree bindings for the Arctic Sand backlight driver
This patch provides devicetree bindings for the Arctic Sand
    driver submitted in the previous patch
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olimpiu Dejeu <redacted>
---

v2 => v3:
- Version updated to match other patch in set. No other changes.
v1 => v2:
- Version updated to match other patch in set. No other changes.

 .../bindings/leds/backlight/arcxcnn_bl.txt         | 31 ++++++++++++++++++++++
 1 file changed, 31 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
new file mode 100644
index 0000000..a7b6ff2
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
@@ -0,0 +1,33 @@
+Binding for ArcticSand arc2c0608 LED driver
+
+Required properties:
+- compatible: should be "arc,arc2c0608"
+- reg: slave address
+
+Optional properties:
+- default-brightness: brightness value on boot, value from: 0-4095
+- label: The name of the backlight device
+			See Documentation/devicetree/bindings/leds/common.txt
+- led-sources: List of enabled channels from 0 to 5.
+			See Documentation/devicetree/bindings/leds/common.txt
+
+- arc,led-config-0: setting for register ILED_CONFIG_0
+- arc,led-config-1: setting for register ILED_CONFIG_1
+- arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
+- arc,comp-config: setting for register CONFIG_COMP
+- arc,filter-config: setting for register FILTER_CONFIG

1 more quoted lines

Nit: Don't you think this is easier to read?

Required properties:
- compatible:		should be "arc,arc2c0608"
- reg:			slave address

Optional properties:
- default-brightness:	brightness value on boot, value from: 0-4095
- label:		The name of the backlight device
			See Documentation/devicetree/bindings/leds/common.txt
- led-sources:		List of enabled channels from 0 to 5.
			See Documentation/devicetree/bindings/leds/common.txt

- arc,led-config-0:	setting for register ILED_CONFIG_0
- arc,led-config-1:	setting for register ILED_CONFIG_1
- arc,dim-freq:		PWM mode frequence setting (bits [3:0] used)
- arc,comp-config:	setting for register CONFIG_COMP
- arc,filter-config:	setting for register FILTER_CONFIG
- arc,trim-config:	setting for register IMAXTUNE
quoted hunk
+
+Note: Optional properties not specified will default to values in IC EPROM
+
+Example:
+
+arc2c0608@30 {
+	compatible = "arc,arc2c0608";
+	reg = <0x30>;
+	default-brightness = <500>;
+	label = "lcd-backlight";
+	linux,default-trigger = "backlight";
+	led-sources = <0 1 2 5>;
+};
+
-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
Keyboard shortcuts
hback out one level
jnext message in thread / next series-diff position
kprevious message in thread / previous series-diff position
ldrill in
Escclose help / fold thread tree
?toggle this help