On 7 September 2015 at 22:50, Rob Herring [off-list ref] wrote:
On Mon, Sep 7, 2015 at 7:23 AM, Tomeu Vizoso [off-list ref] wrote:
quoted
Hello,
I have a problem with the panel on my Tegra Chromebook taking longer
than expected to be ready during boot (Stéphane Marchesin reported what
is basically the same issue in [0]), and have looked into ordered
probing as a better way of solving this than moving nodes around in the
DT or playing with initcall levels and linking order.
While reading the thread [1] that Alexander Holler started with his
series to make probing order deterministic, it occurred to me that it
should be possible to achieve the same by probing devices as they are
referenced by other devices.
This basically reuses the information that is already implicit in the
probe() implementations, saving us from refactoring existing drivers or
adding information to DTBs.
During review of v1 of this series Linus Walleij suggested that it
should be the device driver core to make sure that dependencies are
ready before probing a device. I gave this idea a try [2] but Mark Brown
pointed out to the logic duplication between the resource acquisition
and dependency discovery code paths (though I think it's fairly minor).
To address that code duplication I experimented with Arnd's devm_probe
[3] concept of having drivers declare their dependencies instead of
acquiring them during probe, and while it worked [4], I don't think we
end up winning anything when compared to just probing devices on-demand
from resource getters.
One remaining objection is to the "sprinkling" of calls to
of_device_probe() in the resource getters of each subsystem, but I think
it's the right thing to do given that the storage of resources is
currently subsystem-specific.
We could avoid the above by moving resource storage into the core, but I
don't think there's a compelling case for that.
I have tested this on boards with Tegra, iMX.6, Exynos, Rockchip and
OMAP SoCs, and these patches were enough to eliminate all the deferred
probes (except one in PandaBoard because omap_dma_system doesn't have a
firmware node as of yet).
Have submitted a branch [5] with only these patches on top of thursday's
linux-next to kernelci.org and I don't see any issues that could be
caused by them. For some reason it currently has more passes than the
version of -next it's based on!
With this series I get the kernel to output to the panel in 0.5s,
instead of 2.8s.
Regards,
Tomeu
[0] http://lists.freedesktop.org/archives/dri-devel/2014-August/066527.html
[1] https://lkml.org/lkml/2014/5/12/452
[2] https://lkml.org/lkml/2015/6/17/305
[3] http://article.gmane.org/gmane.linux.ports.arm.kernel/277689
[4] https://lkml.org/lkml/2015/7/21/441a
[5] https://git.collabora.com/cgit/user/tomeu/linux.git/log/?h=on-demand-probes-v6
[6] http://kernelci.org/boot/all/job/collabora/kernel/v4.2-11902-g25d80c927f8b/
[7] http://kernelci.org/boot/all/job/next/kernel/next-20150903/
Changes in v4:
- Added bus.pre_probe callback so the probes of Primecell devices can be
deferred if their device IDs cannot be yet read because of the clock
driver not having probed when they are registered. Maybe this goes
overboard and the matching information should be in the DT if there is
one.
Seems overboard to me or at least a separate problem.
It's a separate problem but this was preventing the series from
working on a few boards.
Most clocks have
to be setup before the driver model simply because timers depend on
clocks usually.
Yes, but in this case the apb clocks for the primecell devices are
implemented in a normal platform driver (vexpress_osc_driver), instead
of using CLK_OF_DECLARE.
Regards,
Tomeu
Rob
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/