On Sun, 2002-05-12 at 10:34, Ani Joshi wrote:
What video board and arch (i'm assuming i386)?
May 12 07:08:53 turbulence kernel: Linux version 2.4.19-pre8-ac2
(root@turbulence.megapathdsl.net) (gcc version 2.96 20000731 (Red Hat
Linux 7.1 2.96-98)) #1 Sun May 12 00:41:02 PDT 2002
May 12 07:08:54 turbulence kernel: Kernel command line: ro
root=/dev/hda6 hdd=ide-scsi console=ttyS0,38400 console=tty0
video=riva:1600x1200-16
May 12 07:08:54 turbulence kernel: Local APIC disabled by BIOS --
reenabling.
May 12 07:08:54 turbulence kernel: Found and enabled local APIC!
May 12 07:08:54 turbulence kernel: Initializing CPU#0
May 12 07:08:54 turbulence kernel: CPU: Before vendor init, caps:
0183fbff c1c3fbff 00000000, vendor = 2
May 12 07:08:54 turbulence kernel: CPU: L1 I Cache: 64K (64 bytes/line),
D cache 64K (64 bytes/line)
May 12 07:08:54 turbulence kernel: CPU: L2 Cache: 512K (64 bytes/line)
May 12 07:08:54 turbulence kernel: CPU: After vendor init, caps:
0183fbff c1c3fbff 00000000 00000000
May 12 07:08:54 turbulence kernel: Intel machine check architecture
supported.
May 12 07:08:54 turbulence kernel: Intel machine check reporting enabled
on CPU#0.
May 12 07:08:54 turbulence kernel: CPU: After generic, caps:
0183fbff c1c3fbff 00000000 00000000
May 12 07:08:54 turbulence kernel: CPU: Common caps:
0183fbff c1c3fbff 00000000 00000000
May 12 07:08:56 turbulence kernel: rivafb: RIVA MTRR set to ON
May 12 07:08:57 turbulence kernel: rivafb: PCI nVidia NV10 framebuffer
ver 0.9.3 (GeForce-DDR, 32MB @ 0xE8000000)
01:05.0 VGA compatible controller: nVidia Corporation GeForce 256 DDR
(rev 10) (prog-if 00 [VGA])
Subsystem: VISIONTEK: Unknown device 000b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at feaf0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
ani
On Sat, 11 May 2002, Miles Lane wrote:
quoted
I am running development kernel 2.5.15 and am having some
trouble getting rivafb to display in the correct mode.
After booting with "video=riva:1600x1200-16", fbset says:
mode "1600x1200-60"
# D: 162.022 MHz, H: 75.010 kHz, V: 60.008 Hz
geometry 1600 1200 1600 1200 16
timings 6172 304 64 46 1 192 3
hsync high
vsync high
accel true
rgba 5/11,6/5,5/0,0/0
endmode
But the Tux logo is all purple. After running fbset -a "1600x1200-76",
I seem to have the correct mode:
mode "1600x1200-76"
# D: 197.981 MHz, H: 95.183 kHz, V: 76.146 Hz
geometry 1600 1200 1600 1200 8
timings 5051 304 40 42 3 136 5
accel true
rgba 8/0,8/0,8/0,0/0
endmode
What do I need to change about my append= line in order to get
the corrent mode set at boot time or is this a bug in the
rivafb code in 2.5.15?
_______________________________________________________________
Have big pipes? SourceForge.net is looking for download mirrors. We supply
the hardware. You get the recognition. Email Us: bandwidth@sourceforge.net
_______________________________________________
Linux-fbdev-devel mailing list
Linux-fbdev-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-fbdev-devel
_______________________________________________________________
Have big pipes? SourceForge.net is looking for download mirrors. We supply
the hardware. You get the recognition. Email Us: bandwidth@sourceforge.net