Sure, here it is:
snow / # lspci -vxxx -s 7.0
00:07.0 ISA bridge: Contaq Microsystems 82c693
        Flags: bus master, medium devsel, latency 0
        Kernel modules: pata_cypress
00: 80 10 93 c6 47 00 80 02 00 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 03 02 00 00 26 60 00 01 f0 60 00 80 80 71 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Best regards,
Barnabas

ps.: let me know, if anything else I can do.

On Tue, Mar 23, 2021 at 7:43 PM Russell King - ARM Linux admin
[off-list ref] wrote:

On Mon, Mar 22, 2021 at 06:10:01PM +0100, Cye Borg wrote:

quoted

PWS 500au:

snow / # lspci -vvx -s 7.1
00:07.1 IDE interface: Contaq Microsystems 82c693 (prog-if 80 [ISA
Compatibility mode-only controller, supports bus mastering])
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

quoted

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin A routed to IRQ 0
        Region 0: I/O ports at 01f0 [size=8]
        Region 1: I/O ports at 03f4
        Region 4: I/O ports at 9080 [size=16]
        Kernel driver in use: pata_cypress
        Kernel modules: pata_cypress
00: 80 10 93 c6 45 00 80 02 00 80 01 01 00 00 80 00
10: f1 01 00 00 f5 03 00 00 00 00 00 00 00 00 00 00
20: 81 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00

snow / # lspci -vvx -s 7.2
00:07.2 IDE interface: Contaq Microsystems 82c693 (prog-if 00 [ISA
Compatibility mode-only controller])
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

quoted

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin B routed to IRQ 0
        Region 0: I/O ports at 0170 [size=8]
        Region 1: I/O ports at 0374
        Region 4: Memory at 0c240000 (32-bit, non-prefetchable)
[disabled] [size=64K]
        Kernel modules: pata_cypress
00: 80 10 93 c6 45 00 80 02 00 00 01 01 00 00 80 00
10: 71 01 00 00 75 03 00 00 00 00 00 00 00 00 00 00
20: 00 00 24 0c 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00 00

Thanks very much.

Could I also ask for the output of:

# lspci -vxxx -s 7.0

as well please - this will dump all 256 bytes for the ISA bridge, which
contains a bunch of configuration registers. Thanks.

--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!