Re: [PATCH] net: fix e100.rst Documentation build errors
From: Jani Nikula <jani.nikula@linux.intel.com>
Date: 2018-06-18 08:05:05
Also in:
lkml, netdev
On Sat, 16 Jun 2018, Randy Dunlap [off-list ref] wrote:
From: Randy Dunlap <redacted> Fix Documentation build errors in e100.rst. Several section titles and the corresponding underlines should not be indented.
Really the content blocks below the titles should not be indented either. It's not an error, but the end result is probably not what you want. BR, Jani.
quoted hunk ↗ jump to hunk
Documentation/networking/e100.rst:90: (SEVERE/4) Unexpected section title. Documentation/networking/e100.rst:109: (SEVERE/4) Unexpected section title. Fixes: 85d63445f411 ("Documentation: e100: Update the Intel 10/100 driver doc") Signed-off-by: Randy Dunlap <redacted> Cc: Jeff Kirsher <redacted> Cc: Aaron Brown <redacted> --- Is there a Sphinx version problem here? Tested-by: should indicate that there was no error like I am seeing. Documentation/networking/e100.rst | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-)--- lnx-418-rc1.orig/Documentation/networking/e100.rst +++ lnx-418-rc1/Documentation/networking/e100.rst@@ -86,8 +86,8 @@ Event Log Message Level: The driver use Additional Configurations ========================= - Configuring the Driver on Different Distributions - ------------------------------------------------- +Configuring the Driver on Different Distributions +------------------------------------------------- Configuring a network driver to load properly when the system is started is distribution dependent. Typically, the configuration process involves adding@@ -105,8 +105,8 @@ Additional Configurations alias eth0 e100 alias eth1 e100 - Viewing Link Messages - --------------------- +Viewing Link Messages +--------------------- In order to see link messages and other Intel driver information on your console, you must set the dmesg level up to six. This can be done by entering the following on the command line before loading the e100 driver::@@ -119,8 +119,8 @@ Additional Configurations NOTE: This setting is not saved across reboots. - ethtool - ------- +ethtool +------- The driver utilizes the ethtool interface for driver configuration and diagnostics, as well as displaying statistical information. The ethtool@@ -129,8 +129,8 @@ Additional Configurations The latest release of ethtool can be found from https://www.kernel.org/pub/software/network/ethtool/ - Enabling Wake on LAN* (WoL) - --------------------------- +Enabling Wake on LAN* (WoL) +--------------------------- WoL is provided through the ethtool* utility. For instructions on enabling WoL with ethtool, refer to the ethtool man page.@@ -138,16 +138,16 @@ Additional Configurations this driver version, in order to enable WoL, the e100 driver must be loaded when shutting down or rebooting the system. - NAPI - ---- +NAPI +---- NAPI (Rx polling mode) is supported in the e100 driver. See https://wiki.linuxfoundation.org/networking/napi for more information on NAPI. - Multiple Interfaces on Same Ethernet Broadcast Network - ------------------------------------------------------ +Multiple Interfaces on Same Ethernet Broadcast Network +------------------------------------------------------ Due to the default ARP behavior on Linux, it is not possible to have one system on two IP networks in the same Ethernet broadcast domain --To unsubscribe from this list: send the line "unsubscribe linux-doc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
-- Jani Nikula, Intel Open Source Graphics Center -- To unsubscribe from this list: send the line "unsubscribe linux-doc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html