[PATCH] dt-bindings: mfd: rockchip,rk805: Convert pinctrl to DT schema

@@ -77,6 +77,21 @@ properties:
     description:
       The input supply for LDO_REG3.
 
+  # pinctrl-bindings.txt allows the pin configuration nodes to be grandchildren
+  # of the pin controller, and the text binding this replaces used that layout:
+  # a "pinmux" node holding the nodes that carry "pins". The driver reaches both
+  # layouts, because pinconf_generic_dt_node_to_map() parses the referenced node
+  # and then walks its children.
+  pinmux:
+    type: object
+    additionalProperties: false
+    patternProperties:
+      '^.+$':
+        if:
+          type: object
+        then:
+          $ref: '#/$defs/rk805-pin-config'
+
   regulators:
     type: object
     patternProperties:

@@ -86,6 +101,38 @@ properties:
         unevaluatedProperties: false
     unevaluatedProperties: false
 
+$defs:
+  rk805-pin-config:
+    type: object
+    description:
+      The RK805 has two output-only GPIOs which can be muxed to the GPIO
+      function and driven low or high at boot.
+    additionalProperties: false
+
+    properties:
+      pins:
+        description:
+          List of GPIO pins to configure.
+        items:
+          enum: [gpio0, gpio1]
+        minItems: 1
+        maxItems: 2
+
+      function:
+        description:
+          The RK805 only supports the GPIO function.
+        enum: [gpio]
+
+      output-low: true
+      output-high: true
+
+    required:
+      - pins
+
+patternProperties:
+  '-pins$':
+    $ref: '#/$defs/rk805-pin-config'
+
 allOf:
   - if:
       properties:

@@ -125,9 +172,11 @@ examples:
             interrupt-parent = <&gpio2>;
             interrupts = <RK_PA6 IRQ_TYPE_LEVEL_LOW>;
             pinctrl-names = "default";
-            pinctrl-0 = <&pmic_int_l>;
+            pinctrl-0 = <&pmic_int_l>, <&rk805_default>, <&rk805_grouped>;
             rockchip,system-power-controller;
             wakeup-source;
+            gpio-controller;
+            #gpio-cells = <2>;
             #clock-cells = <0>;
 
             vcc1-supply = <&vcc_sys>;

@@ -137,6 +186,20 @@ examples:
             vcc5-supply = <&vcc_io>;
             vcc6-supply = <&vcc_io>;
 
+            rk805_default: rk805-default-pins {
+                pins = "gpio0";
+                function = "gpio";
+                output-high;
+            };
+
+            rk805_grouped: pinmux {
+                gpio01 {
+                    pins = "gpio1";
+                    function = "gpio";
+                    output-low;
+                };
+            };
+
             regulators {
                 vdd_logic: DCDC_REG1 {
                     regulator-name = "vdd_logic";

@@ -1,63 +0,0 @@
-Pincontrol driver for RK805 Power management IC.
-
-RK805 has 2 pins which can be configured as GPIO output only.
-
-Please refer file <devicetree/bindings/pinctrl/pinctrl-bindings.txt>
-for details of the common pinctrl bindings used by client devices,
-including the meaning of the phrase "pin configuration node".
-
-Optional Pinmux properties:
---------------------------
-Following properties are required if default setting of pins are required
-at boot.
-- pinctrl-names: A pinctrl state named per <pinctrl-bindings.txt>.
-- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per
-		<pinctrl-bindings.txt>.
-
-The pin configurations are defined as child of the pinctrl states node. Each
-sub-node have following properties:
-
-Required properties:
-------------------
-- #gpio-cells: Should be two. The first cell is the pin number and the
-  second is the GPIO flags.
-
-- gpio-controller: Marks the device node as a GPIO controller.
-
-- pins: List of pins. Valid values of pins properties are: gpio0, gpio1.
-
-First 2 properties must be added in the RK805 PMIC node, documented in
-Documentation/devicetree/bindings/mfd/rockchip,rk808.yaml
-
-Optional properties:
--------------------
-Following are optional properties defined as pinmux DT binding document
-<pinctrl-bindings.txt>. Absence of properties will leave the configuration
-on default.
-	function,
-	output-low,
-	output-high.
-
-Valid values for function properties are: gpio.
-
-There are also not customised properties for any GPIO.
-
-Example:
---------
-rk805: rk805@18 {
-	compatible = "rockchip,rk805";
-	...
-	gpio-controller;
-	#gpio-cells = <2>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pmic_int_l>, <&rk805_default>;
-
-	rk805_default: pinmux {
-		gpio01 {
-			pins = "gpio0", "gpio1";
-			function = "gpio";
-			output-high;
-		};
-	};
-};