[PATCH] dt-bindings: iio: adc: xlnx,xadc: Convert to DT schema

@@ -1,141 +0,0 @@
-Xilinx XADC device driver
-
-This binding document describes the bindings for the Xilinx 7 Series XADC as well
-as the UltraScale/UltraScale+ System Monitor.
-
-The Xilinx XADC is an ADC that can be found in the Series 7 FPGAs from Xilinx.
-The XADC has a DRP interface for communication. Currently two different
-frontends for the DRP interface exist. One that is only available on the ZYNQ
-family as a hardmacro in the SoC portion of the ZYNQ. The other one is available
-on all series 7 platforms and is a softmacro with a AXI interface. This binding
-document describes the bindings for both of them since the bindings are very
-similar.
-
-The Xilinx System Monitor is an ADC that is found in the UltraScale and
-UltraScale+ FPGAs from Xilinx. The System Monitor provides a DRP interface for
-communication. Xilinx provides a standard IP core that can be used to access the
-System Monitor through an AXI interface in the FPGA fabric. This IP core is
-called the Xilinx System Management Wizard. This document describes the bindings
-for this IP.
-
-Required properties:
-	- compatible: Should be one of
-		* "xlnx,zynq-xadc-1.00.a": When using the ZYNQ device
-		  configuration interface to interface to the XADC hardmacro.
-		* "xlnx,axi-xadc-1.00.a": When using the axi-xadc pcore to
-		  interface to the XADC hardmacro.
-		* "xlnx,system-management-wiz-1.3": When using the
-		  Xilinx System Management Wizard fabric IP core to access the
-		  UltraScale and UltraScale+ System Monitor.
-	- reg: Address and length of the register set for the device
-	- interrupts: Interrupt for the XADC control interface.
-	- clocks: When using the ZYNQ this must be the ZYNQ PCAP clock,
-	  when using the axi-xadc or the axi-system-management-wizard this must be
-	  the clock that provides the clock to the AXI bus interface of the core.
-
-Optional properties:
-	- xlnx,external-mux:
-		* "none": No external multiplexer is used, this is the default
-		  if the property is omitted.
-		* "single": External multiplexer mode is used with one
-		   multiplexer.
-		* "dual": External multiplexer mode is used with two
-		  multiplexers for simultaneous sampling.
-	- xlnx,external-mux-channel: Configures which pair of pins is used to
-	  sample data in external mux mode.
-	  Valid values for single external multiplexer mode are:
-		0: VP/VN
-		1: VAUXP[0]/VAUXN[0]
-		2: VAUXP[1]/VAUXN[1]
-		...
-		16: VAUXP[15]/VAUXN[15]
-	  Valid values for dual external multiplexer mode are:
-		1: VAUXP[0]/VAUXN[0] - VAUXP[8]/VAUXN[8]
-		2: VAUXP[1]/VAUXN[1] - VAUXP[9]/VAUXN[9]
-		...
-		8: VAUXP[7]/VAUXN[7] - VAUXP[15]/VAUXN[15]
-
-	  This property needs to be present if the device is configured for
-	  external multiplexer mode (either single or dual). If the device is
-	  not using external multiplexer mode the property is ignored.
-	- xnlx,channels: List of external channels that are connected to the ADC
-	  Required properties:
-		* #address-cells: Should be 1.
-		* #size-cells: Should be 0.
-
-	  The child nodes of this node represent the external channels which are
-	  connected to the ADC. If the property is no present no external
-	  channels will be assumed to be connected.
-
-	  Each child node represents one channel and has the following
-	  properties:
-		Required properties:
-			* reg: Pair of pins the channel is connected to.
-				0: VP/VN
-				1: VAUXP[0]/VAUXN[0]
-				2: VAUXP[1]/VAUXN[1]
-				...
-				16: VAUXP[15]/VAUXN[15]
-			  Note each channel number should only be used at most
-			  once.
-		Optional properties:
-			* xlnx,bipolar: If set the channel is used in bipolar
-			  mode.
-
-
-Examples:
-	xadc@f8007100 {
-		compatible = "xlnx,zynq-xadc-1.00.a";
-		reg = <0xf8007100 0x20>;
-		interrupts = <0 7 4>;
-		interrupt-parent = <&gic>;
-		clocks = <&pcap_clk>;
-
-		xlnx,channels {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			channel@0 {
-				reg = <0>;
-			};
-			channel@1 {
-				reg = <1>;
-			};
-			channel@8 {
-				reg = <8>;
-			};
-		};
-	};
-
-	xadc@43200000 {
-		compatible = "xlnx,axi-xadc-1.00.a";
-		reg = <0x43200000 0x1000>;
-		interrupts = <0 53 4>;
-		interrupt-parent = <&gic>;
-		clocks = <&fpga1_clk>;
-
-		xlnx,channels {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			channel@0 {
-				reg = <0>;
-				xlnx,bipolar;
-			};
-		};
-	};
-
-	adc@80000000 {
-		compatible = "xlnx,system-management-wiz-1.3";
-		reg = <0x80000000 0x1000>;
-		interrupts = <0 81 4>;
-		interrupt-parent = <&gic>;
-		clocks = <&fpga1_clk>;
-
-		xlnx,channels {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			channel@0 {
-				reg = <0>;
-				xlnx,bipolar;
-			};
-		};
-	};

@@ -0,0 +1,123 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/xlnx,xadc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx XADC and System Monitor
+
+maintainers:
+  - Jonathan Cameron <jic23@kernel.org>
+
+description:
+  The Xilinx XADC is an ADC found in the 7 Series FPGAs. It has a DRP
+  interface for communication, which can be reached either through the ZYNQ
+  device configuration interface or through the axi-xadc pcore. The Xilinx
+  System Monitor is an equivalent ADC found in the UltraScale and UltraScale+
+  FPGAs, accessed through the System Management Wizard IP core.
+
+properties:
+  compatible:
+    enum:
+      - xlnx,zynq-xadc-1.00.a
+      - xlnx,axi-xadc-1.00.a
+      - xlnx,system-management-wiz-1.3
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    description: Interrupt for the XADC control interface.
+    maxItems: 1
+
+  clocks:
+    description:
+      When using the ZYNQ this is the ZYNQ PCAP clock. When using the
+      axi-xadc or the axi-system-management-wizard this is the clock that
+      feeds the AXI bus interface of the core.
+    maxItems: 1
+
+  xlnx,external-mux:
+    description:
+      External multiplexer mode. When omitted no external multiplexer is
+      assumed to be used.
+    enum: [none, single, dual]
+    default: none
+
+  xlnx,external-mux-channel:
+    description:
+      Which pair of pins is used to sample data in external multiplexer mode.
+      In single mode the valid range is 0 to 16, in dual mode 1 to 8. This
+      property is required when external multiplexer mode is used and is
+      otherwise ignored.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 16
+
+  xlnx,channels:
+    description:
+      Container for the external channels connected to the ADC. When this
+      node is absent no external channels are assumed to be connected.
+    type: object
+    additionalProperties: false
+
+    properties:
+      '#address-cells':
+        const: 1
+
+      '#size-cells':
+        const: 0
+
+    patternProperties:
+      "^channel@[0-9a-f]+$":
+        type: object
+        additionalProperties: false
+
+        properties:
+          reg:
+            description:
+              Pair of pins the channel is connected to. 0 is VP/VN and 1 to
+              16 are VAUXP/VAUXN pairs. Each channel number may be used at
+              most once.
+            maxItems: 1
+
+          xlnx,bipolar:
+            description: If set the channel is used in bipolar mode.
+            type: boolean
+
+        required:
+          - reg
+
+required:
+  - compatible
+  - reg
+  - clocks
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    xadc@f8007100 {
+        compatible = "xlnx,zynq-xadc-1.00.a";
+        reg = <0xf8007100 0x20>;
+        interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-parent = <&gic>;
+        clocks = <&pcap_clk>;
+
+        xlnx,channels {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            channel@0 {
+                reg = <0>;
+            };
+
+            channel@1 {
+                reg = <1>;
+                xlnx,bipolar;
+            };
+        };
+    };
+...