[PATCH v7 0/3] Samsung Expressatt: Camera Flash

This small series adds camera flash to an existing similar mainline
driver and adds it to the Samsung Expressatt's DTS

// Tests

// # Navigate to LED
sudo su
cd /sys/class/leds/white:flash

// # Should stay at dim brightness
echo 1 > brightness
echo 1 > brightness
echo 1 > brightness
echo 1 > brightness
echo 0 > brightness           # LED_OFF

// # Max Brightness
echo 50 > brightness
echo 0 > brightness           # LED_OFF
echo 99 > brightness
echo 0 > brightness           # LED_OFF
echo 1000 > brightness
echo 0 > brightness           # LED_OFF
echo 100 > brightness
echo 0 > brightness           # LED_OFF

// # Should increase in brightness
for i in $(seq 1 16); do echo $i > brightness; sleep 1; done
echo 0 > brightness           # LED_OFF

// # Test flash strobe (rt8515_led_flash_strobe_set)
cat max_flash_timeout          # check max
echo 200000 > flash_timeout    # 200ms
echo 1 > flash_strobe          # strobe ON → brightness_commit + timer
cat flash_strobe               # should read 1, then 0 after timeout
sleep 1
cat flash_strobe               # should be 0 (timer fired)

// # Test manual strobe cancel
echo 1 > flash_strobe ; echo 0 > flash_strobe          # immediate off

// # Check regulator error handling
dmesg | tail -20                     # look for any "failed to turn off LED" msgs

// # Multiple strobes shouldn't cause errors
echo 200000 > flash_timeout
echo 1 > flash_strobe
echo 1 > flash_strobe
sleep 1
cat flash_strobe
dmesg | tail -20

// # Multiple strobes shouldn't cause errors (extreme test)
for i in $(seq 1 500); do echo 1 > flash_strobe; echo 0 > flash_strobe; done
dmesg | tail -20

// # Test minimal timeout (turns on briefly)
echo 1 > flash_timeout
echo 1 > flash_strobe
sleep 0.1
cat flash_strobe
dmesg | tail -20

// # Flash strobe overrides brightness and flashes at full brightness
echo 200000 > flash_timeout
echo 1 > brightness
echo 1 > flash_strobe
sleep 1
cat flash_strobe
cat brightness
dmesg | tail -20

Downstream reference:
Link: https://github.com/LineageOS/android_kernel_samsung_d2/blob/stable/cm-12.0-YNG4N/drivers/leds/Makefile#L51
Link: https://github.com/LineageOS/android_kernel_samsung_d2/blob/stable/cm-12.0-YNG4N/arch/arm/mach-msm/board-apexq-camera.c#L591

Signed-off-by: Rudraksha Gupta <redacted>
---
Changes in v7:
- address Lee's comments
- PM8921_MPP_S4 instead of PM8921_GPIO_S4 for the MPP4 power-source
- Link to v6: https://lore.kernel.org/r/20260527-expressatt_camera_flash-v6-0-de0f150024e4@gmail.com (local)

Changes in v6:
- Address Lee Jones's comments:
    - formatting
    - use cancel_delayed_work_sync()
- Link to v5: https://lore.kernel.org/r/20260503-expressatt_camera_flash-v5-0-95524506a799@gmail.com (local)

Changes in v5:
- Address Lee Jones's comments:
    - formatting
    - use devm_regulator_get_optional()
    - use a workqueue instead of a timer
    - previously we were validating ent-gpios xor vin-supply at probe,
        but was removed. update the commit msg to reflect this
- Link to v4: https://lore.kernel.org/r/20260331-expressatt_camera_flash-v4-0-f1e99f474513@gmail.com (local)

Changes in v4:
- Driver:
    - revert function renames
    - add comment to use flash instead if torch pin not available
- Link to v3: https://lore.kernel.org/r/20260326-expressatt_camera_flash-v3-0-e75e5d58990f@gmail.com (local)

Changes in v3:
- DTS:
    - Renamed and reordered nodes
- Driver:
    - Use regulator_is_enabled() instead of reg_enabled
    - remove ent xor vin check
    - remove rt->reg == -ENODEV check
    - rename functions to reflect what they do and added ret's
    - Fixed: LED was increasing in brightness when setting the same
        brightness multiple times
- Link to v2: https://lore.kernel.org/r/20260318-expressatt_camera_flash-v2-0-5c2b9a623dcb@gmail.com (local)

Changes in v2:
- dt-bindings: Explain the hardware and not the driver
- **/*: Use vin-supply instead of unlock-gpio
- expressatt DTS: Reorder pinctrl-*
- expressatt DTS: Define rfs-ohms to a default (couldn't find
                  information about this)
- Link to v1: https://lore.kernel.org/r/20260306-expressatt_camera_flash-v1-0-b1996f7cdfdd@gmail.com (local)

To: Lee Jones <lee@kernel.org>
To: Pavel Machek <pavel@kernel.org>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
To: Linus Walleij <linusw@kernel.org>
To: Liam Girdwood <lgirdwood@gmail.com>
To: Mark Brown <broonie@kernel.org>
To: Bjorn Andersson <andersson@kernel.org>
To: Konrad Dybcio <konradybcio@kernel.org>
Cc: linux-leds@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-msm@vger.kernel.org

---
Rudraksha Gupta (3):
      dt-bindings: leds: rt8515: Support single-GPIO flash ICs with vin supply
      leds: flash: rt8515: Support single-GPIO flash ICs with vin supply
      ARM: dts: qcom: msm8960: expressatt: Add camera flash

 .../devicetree/bindings/leds/richtek,rt8515.yaml   |  34 ++++-
 .../dts/qcom/qcom-msm8960-samsung-expressatt.dts   |  44 ++++++
 drivers/leds/flash/leds-rt8515.c                   | 147 +++++++++++++++------
 3 files changed, 184 insertions(+), 41 deletions(-)
---
base-commit: 237a1c39e8dfd3e1c6f1f023eea37a48ec04cc63
change-id: 20260306-expressatt_camera_flash-13c15a7427aa
prerequisite-message-id: [ref]
prerequisite-patch-id: 2b24e9ba47500ef05d38e37b40d8ca2dceb4716a

Best regards,
--  
Rudraksha Gupta [off-list ref]