@@ -14955,6 +14955,7 @@ M:	Binbin Zhou <zhoubinbin@loongson.cn>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	Documentation/devicetree/bindings/i2c/loongson,ls2x-i2c.yaml
+F:	drivers/i2c/busses/i2c-ls2x-v2.c
 F:	drivers/i2c/busses/i2c-ls2x.c
 
 LOONGSON PWM DRIVER

@@ -850,6 +850,16 @@ config I2C_LS2X
 	  This driver can also be built as a module. If so, the module
 	  will be called i2c-ls2x.
 
+config I2C_LS2X_V2
+	tristate "Loongson-2 Fast Speed I2C adapter"
+	depends on LOONGARCH || COMPILE_TEST
+	help
+	  If you say yes to this option, support will be included for the
+	  I2C interface on the Loongson-2K0300 SoCs.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called i2c-ls2x-v2.
+
 config I2C_MLXBF
         tristate "Mellanox BlueField I2C controller"
         depends on (MELLANOX_PLATFORM && ARM64) || COMPILE_TEST

@@ -80,6 +80,7 @@ obj-$(CONFIG_I2C_KEBA)		+= i2c-keba.o
 obj-$(CONFIG_I2C_KEMPLD)	+= i2c-kempld.o
 obj-$(CONFIG_I2C_LPC2K)		+= i2c-lpc2k.o
 obj-$(CONFIG_I2C_LS2X)		+= i2c-ls2x.o
+obj-$(CONFIG_I2C_LS2X_V2)	+= i2c-ls2x-v2.o
 obj-$(CONFIG_I2C_MESON)		+= i2c-meson.o
 obj-$(CONFIG_I2C_MICROCHIP_CORE)	+= i2c-microchip-corei2c.o
 obj-$(CONFIG_I2C_MPC)		+= i2c-mpc.o

@@ -0,0 +1,544 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Loongson-2K0300 I2C controller driver
+ *
+ * Copyright (C) 2025-2026 Loongson Technology Corporation Limited
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/time.h>
+#include <linux/types.h>
+#include <linux/units.h>
+
+/* Loongson-2 fast I2C offset registers */
+#define LOONGSON2_I2C_CR1	0x00	/* I2C control 1 register */
+#define LOONGSON2_I2C_CR2	0x04	/* I2C control 2 register */
+#define LOONGSON2_I2C_OAR	0x08	/* I2C slave address register */
+#define LOONGSON2_I2C_DR	0x10	/* I2C data register */
+#define LOONGSON2_I2C_SR1	0x14	/* I2C status 1 register */
+#define LOONGSON2_I2C_SR2	0x18	/* I2C status 2 register */
+#define LOONGSON2_I2C_CCR	0x1c	/* I2C clock control register */
+#define LOONGSON2_I2C_TRISE	0x20	/* I2C trise register */
+#define LOONGSON2_I2C_FLTR	0x24
+
+/* Bitfields of I2C control 1 register */
+#define LOONGSON2_I2C_CR1_PE		BIT(0)	/* Peripheral enable */
+#define LOONGSON2_I2C_CR1_START		BIT(8)	/* Start generation */
+#define LOONGSON2_I2C_CR1_STOP		BIT(9)	/* Stop generation */
+#define LOONGSON2_I2C_CR1_ACK		BIT(10)	/* Acknowledge enable */
+#define LOONGSON2_I2C_CR1_POS		BIT(11)	/* Acknowledge/PEC Position (for data reception) */
+
+#define LOONGSON2_I2C_CR1_OP_MASK	(LOONGSON2_I2C_CR1_START | LOONGSON2_I2C_CR1_STOP)
+
+/* Bitfields of I2C control 2 register */
+#define LOONGSON2_I2C_CR2_FREQ		GENMASK(5, 0)	/* APB Clock Frequency in MHz */
+#define LOONGSON2_I2C_CR2_ITERREN	BIT(8)	/* Fault-Class Interrupt Enable */
+#define LOONGSON2_I2C_CR2_ITEVTEN	BIT(9)	/* Event-Based Interrupt Enable */
+#define LOONGSON2_I2C_CR2_ITBUFEN	BIT(10)	/* Cache-Class Interrupt Enable */
+
+#define LOONGSON2_I2C_CR2_INT_MASK	\
+	(LOONGSON2_I2C_CR2_ITBUFEN | LOONGSON2_I2C_CR2_ITEVTEN | LOONGSON2_I2C_CR2_ITERREN)
+
+/* Bitfields of I2C status 1 register */
+#define LOONGSON2_I2C_SR1_SB		BIT(0)	/* Start bit (Master mode) */
+#define LOONGSON2_I2C_SR1_ADDR		BIT(1)	/* Address sent (master mode) */
+#define LOONGSON2_I2C_SR1_BTF		BIT(2)	/* Byte transfer finished */
+#define LOONGSON2_I2C_SR1_RXNE		BIT(6)	/* Data register not empty (receivers) */
+#define LOONGSON2_I2C_SR1_TXE		BIT(7)	/* Data register empty (transmitters) */
+#define LOONGSON2_I2C_SR1_BERR		BIT(8)	/* Bus error */
+#define LOONGSON2_I2C_SR1_ARLO		BIT(9)	/* Arbitration lost (master mode) */
+#define LOONGSON2_I2C_SR1_AF		BIT(10)	/* Acknowledge failure */
+
+#define LOONGSON2_I2C_SR1_ITEVTEN_MASK	\
+	(LOONGSON2_I2C_SR1_BTF | LOONGSON2_I2C_SR1_ADDR | LOONGSON2_I2C_SR1_SB)
+#define LOONGSON2_I2C_SR1_ITBUFEN_MASK	(LOONGSON2_I2C_SR1_TXE | LOONGSON2_I2C_SR1_RXNE)
+#define LOONGSON2_I2C_SR1_ITERREN_MASK	\
+	(LOONGSON2_I2C_SR1_AF | LOONGSON2_I2C_SR1_ARLO | LOONGSON2_I2C_SR1_BERR)
+
+/* Bitfields of I2C status 2 register */
+#define LOONGSON2_I2C_SR2_MSL		BIT(0)	/* Master/slave */
+#define LOONGSON2_I2C_SR2_BUSY		BIT(1)	/* Bus busy */
+#define LOONGSON2_I2C_SR2_TRA		BIT(2)	/* Transmitter/receiver */
+#define LOONGSON2_I2C_SR2_GENCALL	BIT(4)	/* General call address (Slave mode) */
+
+/* Bitfields of I2C clock control register */
+#define LOONGSON2_I2C_CCR_CCR		GENMASK(11, 0)
+#define LOONGSON2_I2C_CCR_DUTY		BIT(14)
+#define LOONGSON2_I2C_CCR_FS		BIT(15)
+
+/* Bitfields of I2C trise register */
+#define LOONGSON2_I2C_TRISE_SCL		GENMASK(5, 0)
+
+#define LOONGSON2_I2C_FREE_SLEEP_US	10
+#define LOONGSON2_I2C_FREE_TIMEOUT_US	(2 * USEC_PER_MSEC)
+
+/**
+ * struct loongson2_i2c_msg - client specific data
+ * @buf: data buffer
+ * @count: number of bytes to be transferred
+ * @result: result of the transfer
+ * @addr: 8-bit slave addr, including r/w bit
+ * @stop: last I2C msg to be sent, i.e. STOP to be generated
+ */
+struct loongson2_i2c_msg {
+	u8	*buf;
+	u32	count;
+	int	result;
+	u8      addr;
+	bool	stop;
+};
+
+/**
+ * struct loongson2_i2c_priv - private data of the controller
+ * @adapter: I2C adapter for this controller
+ * @complete: completion of I2C message
+ * @clk: hw i2c clock
+ * @regmap: regmap of the I2C device
+ * @parent_rate_MHz: I2C clock parent rate in MHz
+ * @msg: I2C transfer information
+ */
+struct loongson2_i2c_priv {
+	struct i2c_adapter		adapter;
+	struct completion		complete;
+	struct clk			*clk;
+	struct regmap			*regmap;
+	unsigned long			parent_rate_MHz;
+	struct loongson2_i2c_msg	msg;
+};
+
+static void loongson2_i2c_disable_irq(struct loongson2_i2c_priv *priv)
+{
+	regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR2, LOONGSON2_I2C_CR2_INT_MASK, 0);
+}
+
+static void loongson2_i2c_read_msg(struct loongson2_i2c_priv *priv)
+{
+	struct loongson2_i2c_msg *msg = &priv->msg;
+	u32 rbuf;
+
+	regmap_read(priv->regmap, LOONGSON2_I2C_DR, &rbuf);
+	*msg->buf++ = rbuf;
+	msg->count--;
+}
+
+static void loongson2_i2c_write_msg(struct loongson2_i2c_priv *priv, u8 byte)
+{
+	regmap_write(priv->regmap, LOONGSON2_I2C_DR, byte);
+}
+
+static void loongson2_i2c_terminate_xfer(struct loongson2_i2c_priv *priv)
+{
+	struct loongson2_i2c_msg *msg = &priv->msg;
+
+	loongson2_i2c_disable_irq(priv);
+	regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR1, LOONGSON2_I2C_CR1_OP_MASK,
+			   msg->stop ? LOONGSON2_I2C_CR1_STOP : LOONGSON2_I2C_CR1_START);
+	complete(&priv->complete);
+}
+
+static void loongson2_i2c_handle_write(struct loongson2_i2c_priv *priv)
+{
+	struct loongson2_i2c_msg *msg = &priv->msg;
+
+	if (msg->count) {
+		loongson2_i2c_write_msg(priv, *msg->buf++);
+		if (!--msg->count)
+			regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR2,
+					   LOONGSON2_I2C_CR2_ITBUFEN, 0);
+	} else {
+		loongson2_i2c_terminate_xfer(priv);
+	}
+}
+
+static void loongson2_i2c_handle_rx_addr(struct loongson2_i2c_priv *priv)
+{
+	struct loongson2_i2c_msg *msg = &priv->msg;
+
+	switch (msg->count) {
+	case 0:
+		loongson2_i2c_terminate_xfer(priv);
+		break;
+	case 1:
+		/* Enable NACK and reset POS (Acknowledge position) */
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR1,
+				   LOONGSON2_I2C_CR1_ACK | LOONGSON2_I2C_CR1_POS, 0);
+		/* Set STOP or RepSTART */
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR1, LOONGSON2_I2C_CR1_OP_MASK,
+				   msg->stop ? LOONGSON2_I2C_CR1_STOP : LOONGSON2_I2C_CR1_START);
+		break;
+	case 2:
+		/* Enable NACK */
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR1, LOONGSON2_I2C_CR1_ACK, 0);
+		/* Set POS (NACK position) */
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR1, LOONGSON2_I2C_CR1_POS,
+				   LOONGSON2_I2C_CR1_POS);
+		break;
+
+	default:
+		/* Enable ACK */
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR1, LOONGSON2_I2C_CR1_ACK,
+				   LOONGSON2_I2C_CR1_ACK);
+		/* Reset POS (ACK position) */
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR1, LOONGSON2_I2C_CR1_POS, 0);
+		break;
+	}
+}
+
+static void loongson2_i2c_isr_error(u32 status, void *data)
+{
+	struct loongson2_i2c_priv *priv = data;
+	struct loongson2_i2c_msg *msg = &priv->msg;
+
+	/* Arbitration lost */
+	if (status & LOONGSON2_I2C_SR1_ARLO) {
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_SR1, LOONGSON2_I2C_SR1_ARLO, 0);
+		msg->result = -EAGAIN;
+		goto out;
+	}
+
+	/*
+	 * Acknowledge failure:
+	 * In master transmitter mode a Stop must be generated by software
+	 */
+	if (status & LOONGSON2_I2C_SR1_AF) {
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR1, LOONGSON2_I2C_CR1_STOP,
+				   LOONGSON2_I2C_CR1_STOP);
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_SR1, LOONGSON2_I2C_SR1_AF, 0);
+		msg->result = -EIO;
+		goto out;
+	}
+
+	/* Bus error */
+	if (status & LOONGSON2_I2C_SR1_BERR) {
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_SR1, LOONGSON2_I2C_SR1_BERR, 0);
+		msg->result = -EIO;
+		goto out;
+	}
+
+out:
+	loongson2_i2c_disable_irq(priv);
+	complete(&priv->complete);
+}
+
+static void loongson2_i2c_handle_read(struct loongson2_i2c_priv *priv)
+{
+	struct loongson2_i2c_msg *msg = &priv->msg;
+
+	switch (msg->count) {
+	case 1:
+		loongson2_i2c_disable_irq(priv);
+		loongson2_i2c_read_msg(priv);
+		complete(&priv->complete);
+		break;
+	case 2:
+	case 3:
+		/*
+		 * For 2-byte/3-byte reception and for N-byte reception with N > 3, we have to
+		 * wait for byte transferred finished event before reading data.
+		 * Just disable buffer interrupt in order to avoid another system preemption due
+		 * to RX not empty event.
+		 */
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR2, LOONGSON2_I2C_CR2_ITBUFEN, 0);
+		break;
+	default:
+		/*
+		 * For N byte reception with N > 3 we directly read data register
+		 * until N-2 data.
+		 */
+		loongson2_i2c_read_msg(priv);
+		break;
+	}
+}
+
+static void loongson2_i2c_handle_rx_done(struct loongson2_i2c_priv *priv)
+{
+	struct loongson2_i2c_msg *msg = &priv->msg;
+
+	switch (msg->count) {
+	case 2:
+		/*
+		 * The STOP/START bit has to be set before reading the last two bytes.
+		 * After that, we could read the last two bytes.
+		 */
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR1, LOONGSON2_I2C_CR1_OP_MASK,
+				   msg->stop ? LOONGSON2_I2C_CR1_STOP : LOONGSON2_I2C_CR1_START);
+
+		for (unsigned int i = msg->count; i > 0; i--)
+			loongson2_i2c_read_msg(priv);
+
+		loongson2_i2c_disable_irq(priv);
+
+		complete(&priv->complete);
+		break;
+	case 3:
+		/*
+		 * In order to generate the NACK after the last received data byte, enable NACK
+		 * before reading N-2 data
+		 */
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR1, LOONGSON2_I2C_CR1_ACK, 0);
+		loongson2_i2c_read_msg(priv);
+		break;
+	default:
+		loongson2_i2c_read_msg(priv);
+		break;
+	}
+}
+
+static irqreturn_t loongson2_i2c_isr_event(int irq, void *data)
+{
+	struct loongson2_i2c_priv *priv = data;
+	struct device *dev = priv->adapter.dev.parent;
+	struct loongson2_i2c_msg *msg = &priv->msg;
+	u32 status, ien, event, cr2, possible_status;
+
+	regmap_read(priv->regmap, LOONGSON2_I2C_SR1, &status);
+	if (status & LOONGSON2_I2C_SR1_ITERREN_MASK) {
+		loongson2_i2c_isr_error(status, data);
+		return IRQ_NONE;
+	}
+
+	regmap_read(priv->regmap, LOONGSON2_I2C_CR2, &cr2);
+	ien = cr2 & LOONGSON2_I2C_CR2_INT_MASK;
+
+	/* Update possible_status if buffer interrupt is enabled */
+	possible_status = LOONGSON2_I2C_SR1_ITEVTEN_MASK;
+	if (ien & LOONGSON2_I2C_CR2_ITBUFEN)
+		possible_status |= LOONGSON2_I2C_SR1_ITBUFEN_MASK;
+
+	event = status & possible_status;
+	if (!event) {
+		dev_dbg(dev, "spurious evt irq (status=0x%08x, ien=0x%08x)\n", status, ien);
+		return IRQ_NONE;
+	}
+
+	/* Start condition generated */
+	if (event & LOONGSON2_I2C_SR1_SB)
+		loongson2_i2c_write_msg(priv, msg->addr);
+
+	/* I2C Address sent */
+	if (event & LOONGSON2_I2C_SR1_ADDR) {
+		if (msg->addr & I2C_M_RD)
+			loongson2_i2c_handle_rx_addr(priv);
+		/* Clear ADDR flag */
+		regmap_read(priv->regmap, LOONGSON2_I2C_SR2, &status);
+		/* Enable buffer interrupts for RX/TX not empty events */
+		regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR2, LOONGSON2_I2C_CR2_ITBUFEN,
+				   LOONGSON2_I2C_CR2_ITBUFEN);
+	}
+
+	/* TX empty */
+	if ((event & LOONGSON2_I2C_SR1_TXE) && !(msg->addr & I2C_M_RD))
+		loongson2_i2c_handle_write(priv);
+
+	/* RX not empty */
+	if ((event & LOONGSON2_I2C_SR1_RXNE) && (msg->addr & I2C_M_RD))
+		loongson2_i2c_handle_read(priv);
+
+	/*
+	 * The BTF (Byte Transfer finished) event occurs when:
+	 * - in reception : a new byte is received in the shift register
+	 * but the previous byte has not been read yet from data register
+	 * - in transmission: a new byte should be sent but the data register
+	 * has not been written yet
+	 */
+	if (event & LOONGSON2_I2C_SR1_BTF) {
+		if (msg->addr & I2C_M_RD)
+			loongson2_i2c_handle_rx_done(priv);
+		else
+			loongson2_i2c_handle_write(priv);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int loongson2_i2c_xfer_msg(struct loongson2_i2c_priv *priv, struct i2c_msg *msg,
+				  bool is_stop)
+{
+	struct loongson2_i2c_msg *l_msg = &priv->msg;
+	unsigned long timeout;
+
+	l_msg->addr   = i2c_8bit_addr_from_msg(msg);
+	l_msg->buf    = msg->buf;
+	l_msg->count  = msg->len;
+	l_msg->stop   = is_stop;
+	l_msg->result = 0;
+
+	reinit_completion(&priv->complete);
+
+	/* Enable events and errors interrupts */
+	regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR2,
+			   LOONGSON2_I2C_CR2_ITEVTEN | LOONGSON2_I2C_CR2_ITERREN,
+			   LOONGSON2_I2C_CR2_ITEVTEN | LOONGSON2_I2C_CR2_ITERREN);
+
+	timeout = wait_for_completion_timeout(&priv->complete, priv->adapter.timeout);
+	if (!timeout)
+		return -ETIMEDOUT;
+
+	return l_msg->result;
+}
+
+static int loongson2_i2c_xfer(struct i2c_adapter *i2c_adap, struct i2c_msg msgs[], int num)
+{
+	struct loongson2_i2c_priv *priv = i2c_get_adapdata(i2c_adap);
+	struct device *dev = priv->adapter.dev.parent;
+	unsigned int status;
+	int ret;
+
+	/* Wait I2C bus free */
+	ret = regmap_read_poll_timeout(priv->regmap, LOONGSON2_I2C_SR2, status,
+				       !(status & LOONGSON2_I2C_SR2_BUSY),
+				       LOONGSON2_I2C_FREE_SLEEP_US,
+				       LOONGSON2_I2C_FREE_TIMEOUT_US);
+	if (ret) {
+		dev_dbg(dev, "The I2C bus is busy now.\n");
+		return ret;
+	}
+
+	/* Start generation */
+	regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR1, LOONGSON2_I2C_CR1_START,
+			   LOONGSON2_I2C_CR1_START);
+
+	for (unsigned int i = 0; i < num; i++) {
+		ret = loongson2_i2c_xfer_msg(priv, &msgs[i], i == num - 1);
+		if (ret < 0)
+			return ret;
+	}
+
+	return num;
+}
+
+static u32 loongson2_i2c_func(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+static const struct i2c_algorithm loongson2_i2c_algo = {
+	.xfer		= loongson2_i2c_xfer,
+	.functionality	= loongson2_i2c_func,
+};
+
+static int loongson2_i2c_adjust_bus_speed(struct loongson2_i2c_priv *priv)
+{
+	struct device *dev = priv->adapter.dev.parent;
+	struct i2c_timings i2c_t;
+	u32 val, freq_MHz, ccr;
+
+	i2c_parse_fw_timings(dev, &i2c_t, true);
+	priv->parent_rate_MHz = clk_get_rate(priv->clk);
+
+	if (i2c_t.bus_freq_hz == I2C_MAX_STANDARD_MODE_FREQ) {
+		 /* Select Standard mode */
+		ccr = 0;
+		val = DIV_ROUND_UP(priv->parent_rate_MHz, i2c_t.bus_freq_hz * 2);
+	} else if (i2c_t.bus_freq_hz == I2C_MAX_FAST_MODE_FREQ) {
+		/* Select Fast mode */
+		ccr = LOONGSON2_I2C_CCR_FS;
+		val = DIV_ROUND_UP(priv->parent_rate_MHz, i2c_t.bus_freq_hz * 3);
+	} else {
+		return dev_err_probe(dev, -EINVAL, "Unsupported speed (%uHz)\n", i2c_t.bus_freq_hz);
+	}
+
+	FIELD_MODIFY(LOONGSON2_I2C_CCR_CCR, &ccr, val);
+	regmap_write(priv->regmap, LOONGSON2_I2C_CCR, ccr);
+
+	freq_MHz = DIV_ROUND_UP(priv->parent_rate_MHz, HZ_PER_MHZ);
+	regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR2, LOONGSON2_I2C_CR2_FREQ,
+			   FIELD_GET(LOONGSON2_I2C_CR2_FREQ, freq_MHz));
+
+	regmap_update_bits(priv->regmap, LOONGSON2_I2C_TRISE, LOONGSON2_I2C_TRISE_SCL,
+			   LOONGSON2_I2C_TRISE_SCL);
+
+	/* Enable I2C */
+	regmap_update_bits(priv->regmap, LOONGSON2_I2C_CR1, LOONGSON2_I2C_CR1_PE,
+			   LOONGSON2_I2C_CR1_PE);
+
+	return 0;
+}
+
+static const struct regmap_config loongson2_i2c_regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = LOONGSON2_I2C_TRISE,
+};
+
+static int loongson2_i2c_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct loongson2_i2c_priv *priv;
+	struct i2c_adapter *adap;
+	void __iomem *base;
+	int irq, ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	priv->regmap = devm_regmap_init_mmio(dev, base, &loongson2_i2c_regmap_config);
+	if (IS_ERR(priv->regmap))
+		return dev_err_probe(dev, PTR_ERR(priv->regmap), "Failed to init regmap.\n");
+
+	priv->clk = devm_clk_get_enabled(dev, NULL);
+	if (IS_ERR(priv->clk))
+		return dev_err_probe(dev, PTR_ERR(priv->clk), "Failed to enable clock.\n");
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	adap = &priv->adapter;
+	adap->retries = 5;
+	adap->nr = pdev->id;
+	adap->dev.parent = dev;
+	adap->owner = THIS_MODULE;
+	adap->algo = &loongson2_i2c_algo;
+	adap->timeout = 2 * HZ;
+	device_set_node(&adap->dev, dev_fwnode(dev));
+	i2c_set_adapdata(adap, priv);
+	strscpy(adap->name, pdev->name);
+	init_completion(&priv->complete);
+	platform_set_drvdata(pdev, priv);
+
+	ret = loongson2_i2c_adjust_bus_speed(priv);
+	if (ret)
+		return ret;
+
+	ret = devm_request_irq(dev, irq, loongson2_i2c_isr_event, IRQF_SHARED, pdev->name, priv);
+	if (ret)
+		return ret;
+
+	return devm_i2c_add_adapter(dev, adap);
+}
+
+static const struct of_device_id loongson2_i2c_id_table[] = {
+	{ .compatible = "loongson,ls2k0300-i2c" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, loongson2_i2c_id_table);
+
+static struct platform_driver loongson2_i2c_driver = {
+	.driver = {
+		.name = "loongson2-i2c-v2",
+		.of_match_table = loongson2_i2c_id_table,
+	},
+	.probe = loongson2_i2c_probe,
+};
+module_platform_driver(loongson2_i2c_driver);
+
+MODULE_DESCRIPTION("Loongson-2K0300 I2C bus driver");
+MODULE_AUTHOR("Loongson Technology Corporation Limited");
+MODULE_LICENSE("GPL");