Thread (7 messages) 7 messages, 3 authors, 2024-08-06

RE: [PATCH v3 2/2] arm64: dts: Add support for Kontron i.MX93 OSM-S SoM and BL carrier board

From: Peng Fan <peng.fan@nxp.com>
Date: 2024-08-01 02:10:32
Also in: imx, linux-arm-kernel, lkml

quoted hunk ↗ jump to hunk
Subject: [PATCH v3 2/2] arm64: dts: Add support for Kontron i.MX93
OSM-S SoM and BL carrier board

From: Frieder Schrempf <redacted>

This adds support for the Kontron Electronics OSM-S i.MX93 SoM and
the matching baseboard BL i.MX93.

The SoM hardware complies to the Open Standard Module (OSM) 1.1
specification, size S

Signed-off-by: Frieder Schrempf <redacted>
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx93-kontron-bl-osm-s.dts  | 165 ++++++
 .../dts/freescale/imx93-kontron-osm-s.dtsi    | 547
++++++++++++++++++
 3 files changed, 713 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx93-kontron-
bl-osm-s.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx93-kontron-
osm-s.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile
b/arch/arm64/boot/dts/freescale/Makefile
index f04c22b7de72e..c6e82dfe37576 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -238,6 +238,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qxp-
tqma8xqp-mba8xx.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8ulp-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx93-9x9-qsb.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx93-11x11-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx93-kontron-bl-osm-s.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx93-phyboard-segin.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxca.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxla.dtb diff --
git a/arch/arm64/boot/dts/freescale/imx93-kontron-bl-osm-s.dts
b/arch/arm64/boot/dts/freescale/imx93-kontron-bl-osm-s.dts
new file mode 100644
index 0000000000000..2dfa2381f4691
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx93-kontron-bl-osm-s.dts
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2024 Kontron Electronics GmbH  */
+
+/dts-v1/;
+
+#include "imx93-kontron-osm-s.dtsi"
+
+/ {
+	model = "Kontron BL i.MX93 OSM-S";
+	compatible = "kontron,imx93-bl-osm-s", "kontron,imx93-osm-
s",
+"fsl,imx93";
+
+	aliases {
+		ethernet0 = &fec;
+		ethernet1 = &eqos;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	pwm-beeper {
+		compatible = "pwm-beeper";
+		pwms = <&tpm6 1 5000 0>;
+	};
+
+	reg_vcc_panel: regulator-vcc-panel {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 3 GPIO_ACTIVE_HIGH>;
"enable-active-high" should be put under gpio property.
quoted hunk ↗ jump to hunk
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VCC_PANEL";
+	};
+};
+
+&lpspi8 {
+	status = "okay";
+	assigned-clocks = <&clk IMX93_CLK_LPSPI8>;
+	assigned-clock-parents = <&clk
IMX93_CLK_SYS_PLL_PFD0_DIV2>;
+	assigned-clock-rates = <100000000>;
+
+	eeram@0 {
+		compatible = "microchip,48l640";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&eqos {	/* Second ethernet (OSM-S ETH_B) */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos_rgmii>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-id4f51.e91b";
+			reg = <1>;
+			reset-assert-us = <10000>;
+			reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&fec { /* First ethernet (OSM-S ETH_A) */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet_rgmii>;
+	phy-connection-type = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-id4f51.e91b";
+			reg = <1>;
+			reset-assert-us = <10000>;
+			reset-gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&flexcan1 {
+	status = "okay";
+};
+
+&lpi2c2 {
+	status = "okay";
+
+	gpio_expander_dio: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "DIO1_OUT","DIO1_IN",
"DIO2_OUT","DIO2_IN",
+				  "DIO3_OUT","DIO3_IN",
"DIO4_OUT","DIO4_IN";
+		interrupt-parent = <&gpio4>;
+		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&lpuart1 {
+	status = "okay";
+};
+
+&lpuart7 {
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&lpuart6 {
+	linux,rs485-enabled-at-boot-time;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&tpm6 {
+	status = "okay";
+};
+
+&usbotg1 {
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	usb1@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+	};
+};
+
+&usbotg2 {
+	adp-disable;
+	hnp-disable;
+	srp-disable;
+
+	disable-over-current;
+	dr_mode = "otg";
+	usb-role-switch;
+	status = "okay";
+};
+
+&usdhc2 {
+	vmmc-supply = <&reg_vdd_3v3>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx93-kontron-osm-s.dtsi
b/arch/arm64/boot/dts/freescale/imx93-kontron-osm-s.dtsi
new file mode 100644
index 0000000000000..926c622d380ee
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx93-kontron-osm-s.dtsi
@@ -0,0 +1,547 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2024 Kontron Electronics GmbH  */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx93.dtsi"
+
+/ {
+	model = "Kontron OSM-S i.MX93";
+	compatible = "kontron,imx93-osm-s", "fsl,imx93";
+
+	aliases {
+		rtc0 = &rv3028;
+		rtc1 = &bbnsm_rtc;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	chosen {
+		stdout-path = &lpuart1;
+	};
+
+	reg_usdhc2_vcc: regulator-usdhc2-vcc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vcc>;
+		enable-active-high;
+		gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
"enable-active-high" put under "gpio".

+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "VCC_SDIO_A";
+	};
+
+	reg_vdd_carrier: regulator-vdd-carrier {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_vdd_carrier>;
+		enable-active-high;
+		gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
Ditto.

+		regulator-always-on;
+		regulator-boot-on;
+		regulator-name = "VDD_CARRIER";
+
+		regulator-state-standby {
+			regulator-on-in-suspend;
+		};
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+
+		regulator-state-disk {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&lpspi1 { /* OSM-S SPI_A */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpspi1>;
+	cs-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; };
+
+&lpspi8 { /* OSM-S SPI_B */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpspi8>;
+	cs-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; };
+
+&flexcan1 { /* OSM-S CAN_A */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+};
+
+&flexcan2 { /* OSM-S CAN_B */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>;
+	gpio-line-names = "", "", "I2C_A_SCL", "I2C_A_SDA",
+			  "UART_CON_RX", "UART_CON_TX",
"UART_C_RX", "UART_C_TX",
+			  "CAN_A_TX", "CAN_A_RX", "GPIO_A_0",
"SPI_A_CS0",
+			  "SPI_A_SDI", "SPI_A_SCK","SPI_A_SDO"; };
+
+&gpio2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio2>;
+	gpio-line-names = "I2C_B_SDA", "I2C_B_SCL", "GPIO_B_1",
"GPIO_A_2",
+			  "UART_B_TX", "UART_B_RX", "UART_B_RTS",
"UART_B_CTS",
+			  "UART_A_TX", "UART_A_RX", "UART_A_RTS",
"UART_A_CTS",
+			  "SPI_B_CS0", "SPI_B_SDI", "SPI_B_SDO",
"SPI_B_SCK",
+			  "I2S_BITCLK", "I2S_MCLK", "GPIO_A_1",
"I2S_A_DATA_OUT",
+			  "I2S_A_DATA_IN", "PWM_2", "GPIO_A_3",
"PWM_1",
+			  "PWM_0", "CAN_B_TX", "I2S_LRCLK",
"CAN_B_RX", "GPIO_A_4",
+			  "GPIO_A_5";
+};
+
+&gpio3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio3>;
+	gpio-line-names = "SDIO_A_CD", "SDIO_A_CLK",
"SDIO_A_CMD", "SDIO_A_D0",
+			  "SDIO_A_D1", "SDIO_A_D2", "SDIO_A_D3",
"SDIO_A_PWR_EN",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "SDIO_B_CLK", "SDIO_B_CMD",
"SDIO_B_D0", "SDIO_B_D1",
+			  "SDIO_B_D2", "SDIO_B_D3", "GPIO_A_6",
"GPIO_A_7"; };
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio4>;
+	gpio-line-names = "ETH_B_MDC", "ETH_B_MDIO",
"ETH_B_TXD4", "ETH_B_TXD3",
+			  "ETH_B_TXD2", "ETH_B_TXD1",
"ETH_B_TX_EN", "ETH_B_TX_CLK",
+			  "ETH_B_RX_CTL", "ETH_B_RX_CLK",
"ETH_B_RXD0", "ETH_B_RXD1",
+			  "ETH_B_RXD2", "ETH_B_RXD3", "ETH_MDC",
"ETH_MDIO",
+			  "ETH_A_TXD3", "ETH_A_TXD2",
"ETH_A_TXD1", "ETH_A_TXD0",
+			  "ETH_A_TX_EN", "ETH_A_TX_CLK",
"ETH_A_RX_CTL", "ETH_A_RX_CLK",
+			  "ETH_A_RXD0", "ETH_A_RXD1",
"ETH_A_RXD2", "ETH_A_RXD3",
+			  "GPIO_B_0", "CARRIER_PWR_EN";
+};
+
+&lpi2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c1>;
+	status = "okay";
+
+	pca9451: pmic@25 {
+		compatible = "nxp,pca9451a";
+		reg = <0x25>;
+		nxp,i2c-lt-enable;
+
+		regulators {
+			reg_vdd_soc: BUCK1 { /* dual phase with
BUCK3 */
+				regulator-name = "+0V8_VDD_SOC
(BUCK1)";
+				regulator-min-microvolt = <650000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vddq_ddr: BUCK2 {
+				regulator-name = "+0V6_VDDQ_DDR
(BUCK2)";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <600000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vdd_3v3: BUCK4 {
+				regulator-name = "+3V3 (BUCK4)";
+				regulator-min-microvolt =
<3300000>;
+				regulator-max-microvolt =
<3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_1v8: BUCK5 {
+				regulator-name = "+1V8 (BUCK5)";
+				regulator-min-microvolt =
<1800000>;
+				regulator-max-microvolt =
<1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_dram: BUCK6 {
+				regulator-name =
"+1V1_NVCC_DRAM (BUCK6)";
+				regulator-min-microvolt =
<1100000>;
+				regulator-max-microvolt =
<1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_snvs: LDO1 {
+				regulator-name = "+1V8_NVCC_SNVS
(LDO1)";
+				regulator-min-microvolt =
<1800000>;
+				regulator-max-microvolt =
<1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_ana: LDO4 {
+				regulator-name = "+0V8_VDD_ANA
(LDO4)";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_sd: LDO5 {
+				regulator-name = "NVCC_SD (LDO5)";
+				regulator-min-microvolt =
<1800000>;
+				regulator-max-microvolt =
<3300000>;
+			};
+		};
+	};
+
+	eeprom@50 {
+		compatible = "onnn,n24s64b", "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+		size = <8192>;
+		num-addresses = <1>;
+	};
+
+	rv3028: rtc@52 {
+		compatible = "microcrystal,rv3028";
+		reg = <0x52>;
+	};
+};
+
+&lpi2c2 { /* OSM-S I2C_A */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c2>;
+};
+
+&lpi2c3 { /* OSM-S I2C_B */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c3>;
+};
+
+&tpm3 { /* OSM-S PWM_0 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_tpm3>;
+};
+
+&tpm4 { /* OSM-S PWM_2 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_tpm4>;
+};
+
+&tpm6 { /* OSM-S PWM_1 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_tpm6>;
+};
+
+&lpuart1 { /* OSM-S UART_CON */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart1>;
+};
+
+&lpuart2 { /* OSM-S UART_C */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart2>;
+};
+
+&lpuart6 { /* OSM-S UART_B */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart6>;
+};
+
+&lpuart7 { /* OSM-S UART_A */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart7>;
+};
+
+&usdhc1 { /* eMMC */
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1>;
+	pinctrl-2 = <&pinctrl_usdhc1>;
Same pad settings?

+	vmmc-supply = <&reg_vdd_3v3>;
+	vqmmc-supply = <&reg_vdd_1v8>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 { /* OSM-S SDIO_A */
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
Ditto.

+	vmmc-supply = <&reg_usdhc2_vcc>;
+	cd-gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; };
+
+&usdhc3 { /* OSM-S SDIO_B */
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3>;
+	pinctrl-2 = <&pinctrl_usdhc3>;
Ditto.

Regards,
Peng.
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help