[PATCH v4 2/7] net: phy: Add 10-BaseT1L registers
From: <hidden>
Date: 2021-12-10 10:53:24
Also in:
lkml, netdev
Subsystem:
ethernet phy library, the rest · Maintainers:
Andrew Lunn, Heiner Kallweit, Linus Torvalds
From: Alexandru Tachici <redacted> The 802.3gc specification defines the 10-BaseT1L link mode for ethernet trafic on twisted wire pair. PMA status register can be used to detect if the phy supports 2.4 V TX level and PCS control register can be used to enable/disable PCS level loopback. Signed-off-by: Alexandru Tachici <redacted> --- include/uapi/linux/mdio.h | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+)
diff --git a/include/uapi/linux/mdio.h b/include/uapi/linux/mdio.h
index c54e6eae5366..0b2eba36dd7c 100644
--- a/include/uapi/linux/mdio.h
+++ b/include/uapi/linux/mdio.h@@ -67,6 +67,9 @@ #define MDIO_PCS_10GBRT_STAT2 33 /* 10GBASE-R/-T PCS status 2 */ #define MDIO_AN_10GBT_CTRL 32 /* 10GBASE-T auto-negotiation control */ #define MDIO_AN_10GBT_STAT 33 /* 10GBASE-T auto-negotiation status */ +#define MDIO_B10L_PMA_CTRL 2294 /* 10BASE-T1L PMA control */ +#define MDIO_PMA_10T1L_STAT 2295 /* 10BASE-T1L PMA status */ +#define MDIO_PCS_10T1L_CTRL 2278 /* 10BASE-T1L PCS control */ /* LASI (Link Alarm Status Interrupt) registers, defined by XENPAK MSA. */ #define MDIO_PMA_LASI_RXCTRL 0x9000 /* RX_ALARM control */
@@ -268,6 +271,28 @@ #define MDIO_AN_10GBT_STAT_MS 0x4000 /* Master/slave config */ #define MDIO_AN_10GBT_STAT_MSFLT 0x8000 /* Master/slave config fault */ +/* 10BASE-T1L PMA control */ +#define MDIO_PMA_10T1L_CTRL_LB_EN 0x0001 /* Enable loopback mode */ +#define MDIO_PMA_10T1L_CTRL_EEE_EN 0x0400 /* Enable EEE mode */ +#define MDIO_PMA_10T1L_CTRL_LOW_POWER 0x0800 /* Low-power mode */ +#define MDIO_PMA_10T1L_CTRL_2V4_EN 0x1000 /* Enable 2.4 Vpp operating mode */ +#define MDIO_PMA_10T1L_CTRL_TX_DIS 0x4000 /* Transmit disable */ +#define MDIO_PMA_10T1L_CTRL_PMA_RST 0x8000 /* MA reset */ + +/* 10BASE-T1L PMA status register. */ +#define MDIO_PMA_10T1L_STAT_LINK 0x0001 /* PMA receive link up */ +#define MDIO_PMA_10T1L_STAT_FAULT 0x0002 /* Fault condition detected */ +#define MDIO_PMA_10T1L_STAT_POLARITY 0x0004 /* Receive polarity is reversed */ +#define MDIO_PMA_10T1L_STAT_RECV_FAULT 0x0200 /* Able to detect fault on receive path */ +#define MDIO_PMA_10T1L_STAT_EEE 0x0400 /* PHY has EEE ability */ +#define MDIO_PMA_10T1L_STAT_LOW_POWER 0x0800 /* PMA has low-power ability */ +#define MDIO_PMA_10T1L_STAT_2V4_ABLE 0x1000 /* PHY has 2.4 Vpp operating mode ability */ +#define MDIO_PMA_10T1L_STAT_LB_ABLE 0x2000 /* PHY has loopback ability */ + +/* 10BASE-T1L PCS control register. */ +#define MDIO_PCS_10T1L_CTRL_LB 0x4000 /* Enable PCS level loopback mode */ +#define MDIO_PCS_10T1L_CTRL_RESET 0x8000 /* PCS reset */ + /* EEE Supported/Advertisement/LP Advertisement registers. * * EEE capability Register (3.20), Advertisement (7.60) and
--
2.25.1