[PATCH V5 0/7] Add QSPI and QUPv3 DT nodes for SC7280 SoC

Subsystems: arm/qualcomm chromebook support, arm/qualcomm mailing list, arm/qualcomm support, the rest · Maintainers: Bjorn Andersson, Konrad Dybcio, Linus Torvalds

Series: 7 patches touching 2 files, +1680/-16

STALE1880d SUPERSEDED

Status: Superseded by v10 (posted 2021-09-23). [go to v10]

Revision v5 (7 revisions archived).

Revisions (7)
  1. v4
  2. v5 current [diff against previous]
  3. v6 [diff against previous]
  4. v7 [diff against previous]
  5. v8 [diff against previous]
  6. v9 [diff against previous]
  7. v10 [diff against previous]

24 messages, 3 authors, 2021-09-03 · open the first message on its own page

[PATCH V5 0/7] Add QSPI and QUPv3 DT nodes for SC7280 SoC

From: Rajesh Patil <hidden>
Date: 2021-08-12 07:43:01 

Changes in V5:
 - As per Matthias' comments, I've split the patches as below:
   1. Add QSPI node
   2. Configure SPI-NOR FLASH for sc7280-idp
   3. Add QUPv3 wrapper_0 nodes
   4. Update QUPv3 UART5 DT node
   5. Configure debug uart for sc7280-idp
   6. Configure uart7 to support bluetooth on sc7280-idp
   7. Add QUPv3 wrapper_1 nodes

Changes in V4:
 - As per Stephen's comment updated spi-max-frequency to 37.5MHz, moved
   qspi_opp_table from /soc to / (root).
 - As per Bjorn's comment, added QUP Wrapper_0 nodes
   as separate patch and debug-uart node as separate patch.
 - Dropped interconnect votes for wrapper_0 and wrapper_1 node
 - Corrected QUP Wrapper_1 SE node's pin control functions like below
        QUP Wrapper_0: SE0-SE7 uses qup00 - qup07 pin-cntrl functions.
        QUP Wrapper_1: SE0-SE7 uses qup10 - qup17 pin-cntrl functions.
   
Changes in V3:
 - Broken the huge V2 patch into 3 smaller patches.
   1. QSPI DT nodes
   2. QUP wrapper_0 DT nodes
   3. QUP wrapper_1 DT nodes
   
Changes in V2:
 - As per Doug's comments removed pinmux/pinconf subnodes.
 - As per Doug's comments split of SPI, UART nodes has been done.
 - Moved QSPI node before aps_smmu as per the order.

Rajesh Patil (3):
  arm64: dts: sc7280: Configure SPI-NOR FLASH for sc7280-idp
  arm64: dts: sc7280: Configure debug uart for sc7280-idp
  arm64: dts: sc7280: Configure uart7 to support bluetooth on sc7280-idp

Roja Rani Yarubandi (4):
  arm64: dts: sc7280: Add QSPI node
  arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes
  arm64: dts: sc7280: Update QUPv3 UART5 DT node

10 more lines

[PATCH V5 3/7] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes

From: Rajesh Patil <hidden>
Date: 2021-08-12 07:42:49 

From: Roja Rani Yarubandi <redacted>

Add QUPv3 wrapper_0 DT nodes for SC7280 SoC.

Signed-off-by: Roja Rani Yarubandi <redacted>
Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 720 +++++++++++++++++++++++++++++++++++
 1 file changed, 720 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index f8dd5ff..e461395 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -533,6 +533,25 @@
 
 		};
 
+		qup_opp_table: qup-opp-table {
+			compatible = "operating-points-v2";
+
+			opp-75000000 {
+				opp-hz = /bits/ 64 <75000000>;
+				required-opps = <&rpmhpd_opp_low_svs>;
+			};
+
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+				required-opps = <&rpmhpd_opp_svs>;
+			};
+
+			opp-128000000 {
+				opp-hz = /bits/ 64 <128000000>;
+				required-opps = <&rpmhpd_opp_nom>;
+			};
+		};
+
 		qupv3_id_0: geniqup@9c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0 0x009c0000 0 0x2000>;
@@ -542,8 +561,305 @@
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
+			iommus = <&apps_smmu 0x123 0x0>;
 			status = "disabled";
 
+			i2c0: i2c@980000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c0_data_clk>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi0: spi@980000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>, <&qup_spi0_cs_gpio>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart0: serial@980000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart0_cts>, <&qup_uart0_rts>, <&qup_uart0_tx>, <&qup_uart0_rx>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c1: i2c@984000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00984000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c1_data_clk>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi1: spi@984000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00984000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>, <&qup_spi1_cs_gpio>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart1: serial@984000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00984000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart1_cts>, <&qup_uart1_rts>, <&qup_uart1_tx>, <&qup_uart1_rx>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c2: i2c@988000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00988000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c2_data_clk>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi2: spi@988000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00988000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>, <&qup_spi2_cs_gpio>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart2: serial@988000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00988000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart2_cts>, <&qup_uart2_rts>, <&qup_uart2_tx>, <&qup_uart2_rx>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c3: i2c@98c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0098c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c3_data_clk>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi3: spi@98c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0098c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>, <&qup_spi3_cs_gpio>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart3: serial@98c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x0098c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart3_cts>, <&qup_uart3_rts>, <&qup_uart3_tx>, <&qup_uart3_rx>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c4: i2c@990000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00990000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c4_data_clk>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi4: spi@990000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00990000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>, <&qup_spi4_cs_gpio>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart4: serial@990000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00990000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart4_cts>, <&qup_uart4_rts>, <&qup_uart4_tx>, <&qup_uart4_rx>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c5: i2c@994000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00994000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c5_data_clk>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi5: spi@994000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00994000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>, <&qup_spi5_cs_gpio>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
 			uart5: serial@994000 {
 				compatible = "qcom,geni-debug-uart";
 				reg = <0 0x00994000 0 0x4000>;
@@ -554,6 +870,110 @@
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
 			};
+
+			i2c6: i2c@998000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00998000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c6_data_clk>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi6: spi@998000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00998000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>, <&qup_spi6_cs_gpio>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart6: serial@998000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00998000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart6_cts>, <&qup_uart6_rts>, <&qup_uart6_tx>, <&qup_uart6_rx>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c7: i2c@99c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0099c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c7_data_clk>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi7: spi@99c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0099c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi7_data_clk>, <&qup_spi7_cs>, <&qup_spi7_cs_gpio>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart7: serial@99c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x0099c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart7_cts>, <&qup_uart7_rts>, <&qup_uart7_tx>, <&qup_uart7_rx>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
 		};
 
 		cnoc2: interconnect@1500000 {
@@ -1575,11 +1995,311 @@
 				function = "qspi_data";
 			};
 
+			qup_i2c0_data_clk:qup-i2c0-data-clk {
+				pins = "gpio0", "gpio1";
+				function = "qup00";
+			};
+
+			qup_i2c1_data_clk:qup-i2c1-data-clk {
+				pins = "gpio4", "gpio5";
+				function = "qup01";
+			};
+
+			qup_i2c2_data_clk:qup-i2c2-data-clk {
+				pins = "gpio8", "gpio9";
+				function = "qup02";
+			};
+
+			qup_i2c3_data_clk:qup-i2c3-data-clk {
+				pins = "gpio12", "gpio13";
+				function = "qup03";
+			};
+
+			qup_i2c4_data_clk:qup-i2c4-data-clk {
+				pins = "gpio16", "gpio17";
+				function = "qup04";
+			};
+
+			qup_i2c5_data_clk:qup-i2c5-data-clk {
+				pins = "gpio20", "gpio21";
+				function = "qup05";
+			};
+
+			qup_i2c6_data_clk:qup-i2c6-data-clk {
+				pins = "gpio24", "gpio25";
+				function = "qup06";
+			};
+
+			qup_i2c7_data_clk:qup-i2c7-data-clk {
+				pins = "gpio28", "gpio29";
+				function = "qup07";
+			};
+
+			qup_spi0_data_clk: qup-spi0-data-clk {
+				pins = "gpio0", "gpio1", "gpio2";
+				function = "qup00";
+			};
+
+			qup_spi0_cs: qup-spi0-cs {
+				pins = "gpio3";
+				function = "qup00";
+			};
+
+			qup_spi0_cs_gpio: qup-spi0-cs_gpio {
+				pins = "gpio3";
+				function = "gpio";
+			};
+
+			qup_spi1_data_clk: qup-spi1-data-clk {
+				pins = "gpio4", "gpio5", "gpio6";
+				function = "qup01";
+			};
+
+			qup_spi1_cs: qup-spi1-cs {
+				pins = "gpio7";
+				function = "qup01";
+			};
+
+			qup_spi1_cs_gpio: qup-spi1-cs_gpio {
+				pins = "gpio7";
+				function = "gpio";
+			};
+
+			qup_spi2_data_clk: qup-spi2-data-clk {
+				pins = "gpio8", "gpio9", "gpio10";
+				function = "qup02";
+			};
+
+			qup_spi2_cs: qup-spi2-cs {
+				pins = "gpio11";
+				function = "qup02";
+			};
+
+			qup_spi2_cs_gpio: qup-spi2-cs_gpio {
+				pins = "gpio11";
+				function = "gpio";
+			};
+
+			qup_spi3_data_clk: qup-spi3-data-clk {
+				pins = "gpio12", "gpio13", "gpio14";
+				function = "qup03";
+			};
+
+			qup_spi3_cs: qup-spi3-cs {
+				pins = "gpio15";
+				function = "qup03";
+			};
+
+			qup_spi3_cs_gpio: qup-spi3-cs_gpio {
+				pins = "gpio15";
+				function = "gpio";
+			};
+
+			qup_spi4_data_clk: qup-spi4-data-clk {
+				pins = "gpio16", "gpio17", "gpio18";
+				function = "qup04";
+			};
+
+			qup_spi4_cs: qup-spi4-cs {
+				pins = "gpio19";
+				function = "qup04";
+			};
+
+			qup_spi4_cs_gpio: qup-spi4-cs_gpio {
+				pins = "gpio19";
+				function = "gpio";
+			};
+
+			qup_spi5_data_clk: qup-spi5-data-clk {
+				pins = "gpio20", "gpio21", "gpio22";
+				function = "qup05";
+			};
+
+			qup_spi5_cs: qup-spi5-cs {
+				pins = "gpio23";
+				function = "qup05";
+			};
+
+			qup_spi5_cs_gpio: qup-spi5-cs_gpio {
+				pins = "gpio23";
+				function = "gpio";
+			};
+
+			qup_spi6_data_clk: qup-spi6-data-clk {
+				pins = "gpio24", "gpio25", "gpio26";
+				function = "qup06";
+			};
+
+			qup_spi6_cs: qup-spi6-cs {
+				pins = "gpio27";
+				function = "qup06";
+			};
+
+			qup_spi6_cs_gpio: qup-spi6-cs_gpio {
+				pins = "gpio27";
+				function = "gpio";
+			};
+
+			qup_spi7_data_clk: qup-spi7-data-clk {
+				pins = "gpio28", "gpio29", "gpio30";
+				function = "qup07";
+			};
+
+			qup_spi7_cs: qup-spi7-cs {
+				pins = "gpio31";
+				function = "qup07";
+			};
+
+			qup_spi7_cs_gpio: qup-spi7-cs_gpio {
+				pins = "gpio31";
+				function = "gpio";
+			};
+
+			qup_uart0_cts: qup-uart0-cts {
+				pins = "gpio0";
+				function = "qup00";
+			};
+
+			qup_uart0_rts: qup-uart0-rts {
+				pins = "gpio1";
+				function = "qup00";
+			};
+
+			qup_uart0_tx: qup-uart0-tx {
+				pins = "gpio2";
+				function = "qup00";
+			};
+
+			qup_uart0_rx: qup-uart0-rx {
+				pins = "gpio3";
+				function = "qup00";
+			};
+
+			qup_uart1_cts: qup-uart1-cts {
+				pins = "gpio4";
+				function = "qup01";
+			};
+
+			qup_uart1_rts: qup-uart1-rts {
+				pins = "gpio5";
+				function = "qup01";
+			};
+
+			qup_uart1_tx: qup-uart1-tx {
+				pins = "gpio6";
+				function = "qup01";
+			};
+
+			qup_uart1_rx: qup-uart1-rx {
+				pins = "gpio7";
+				function = "qup01";
+			};
+
+			qup_uart2_cts: qup-uart2-cts {
+				pins = "gpio8";
+				function = "qup02";
+			};
+
+			qup_uart2_rts: qup-uart2-rts {
+				pins = "gpio9";
+				function = "qup02";
+			};
+
+			qup_uart2_tx: qup-uart2-tx {
+				pins = "gpio10";
+				function = "qup02";
+			};
+
+			qup_uart2_rx: qup-uart2-rx {
+				pins = "gpio11";
+				function = "qup02";
+			};
+
+			qup_uart3_cts: qup-uart3-cts {
+				pins = "gpio12";
+				function = "qup03";
+			};
+
+			qup_uart3_rts: qup-uart3-rts {
+				pins = "gpio13";
+				function = "qup03";
+			};
+
+			qup_uart3_tx: qup-uart3-tx {
+				pins = "gpio14";
+				function = "qup03";
+			};
+
+			qup_uart3_rx: qup-uart3-rx {
+				pins = "gpio15";
+				function = "qup03";
+			};
+
+			qup_uart4_cts: qup-uart4-cts {
+				pins = "gpio16";
+				function = "qup04";
+			};
+
+			qup_uart4_rts: qup-uart4-rts {
+				pins = "gpio17";
+				function = "qup04";
+			};
+
+			qup_uart4_tx: qup-uart4-tx {
+				pins = "gpio18";
+				function = "qup04";
+			};
+
+			qup_uart4_rx: qup-uart4-rx {
+				pins = "gpio19";
+				function = "qup04";
+			};
+
 			qup_uart5_default: qup-uart5-default {
 				pins = "gpio46", "gpio47";
 				function = "qup13";
 			};
 
+			qup_uart6_cts: qup-uart6-cts {
+				pins = "gpio24";
+				function = "qup06";
+			};
+
+			qup_uart6_rts: qup-uart6-rts {
+				pins = "gpio25";
+				function = "qup06";
+			};
+
+			qup_uart6_tx: qup-uart6-tx {
+				pins = "gpio26";
+				function = "qup06";
+			};
+
+			qup_uart6_rx: qup-uart6-rx {
+				pins = "gpio27";
+				function = "qup06";
+			};
+
+			qup_uart7_cts: qup-uart7-cts {
+				pins = "gpio28";
+				function = "qup07";
+			};
+
+			qup_uart7_rts: qup-uart7-rts {
+				pins = "gpio29";
+				function = "qup07";
+			};
+
+			qup_uart7_tx: qup-uart7-tx {
+				pins = "gpio30";
+				function = "qup07";
+			};
+
+			qup_uart7_rx: qup-uart7-rx {
+				pins = "gpio31";
+				function = "qup07";
+			};
+
 			sdc1_on: sdc1-on {
 				clk {
 					pins = "sdc1_clk";
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V5 6/7] arm64: dts: sc7280: Configure uart7 to support bluetooth on sc7280-idp

From: Rajesh Patil <hidden>
Date: 2021-08-12 07:42:52 

Add bluetooth uart pin configuration for sc7280-idp.

Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 85 ++++++++++++++++++++++++++++++++
 1 file changed, 85 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 53993b3..7c106c0 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -297,6 +297,16 @@
 	vdda18-supply = <&vreg_l1c_1p8>;
 };
 
+&uart7 {
+	status = "okay";
+
+	/delete-property/interrupts;
+	interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+				<&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+};
+
 /* PINCTRL - additions to nodes defined in sc7280.dtsi */
 
 &qspi_cs0 {
@@ -322,6 +332,81 @@
 	bias-pull-up;
 };
 
+&qup_uart7_cts {
+	/*
+	 * Configure a pull-down on CTS to match the pull of
+	 * the Bluetooth module.
+	 */
+	bias-pull-down;
+};
+
+&qup_uart7_rts {
+	/* We'll drive RTS, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_tx {
+	/* We'll drive TX, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_rx {
+	/*
+	 * Configure a pull-up on RX. This is needed to avoid
+	 * garbage data when the TX pin of the Bluetooth module is
+	 * in tri-state (module powered off or not driving the
+	 * signal yet).
+	 */
+	bias-pull-up;
+};
+
+&tlmm {
+	qup_uart7_sleep_cts: qup-uart7-sleep-cts {
+		pins = "gpio28";
+		function = "gpio";
+		/*
+		 * Configure a pull-down on CTS to match the pull of
+		 * the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_rts: qup-uart7-sleep-rts {
+		pins = "gpio29";
+		function = "gpio";
+		/*
+		 * Configure pull-down on RTS. As RTS is active low
+		 * signal, pull it low to indicate the BT SoC that it
+		 * can wakeup the system anytime from suspend state by
+		 * pulling RX low (by sending wakeup bytes).
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_tx: qup-uart7-sleep-tx {
+		pins = "gpio30";
+		function = "gpio";
+		/*
+		 * Configure pull-up on TX when it isn't actively driven
+		 * to prevent BT SoC from receiving garbage during sleep.
+		 */
+		bias-pull-up;
+	};
+
+	qup_uart7_sleep_rx: qup-uart7-sleep-rx {
+		pins = "gpio31";
+		function = "gpio";
+		/*
+		 * Configure a pull-up on RX. This is needed to avoid
+		 * garbage data when the TX pin of the Bluetooth module
+		 * is floating which may cause spurious wakeups.
+		 */
+		bias-pull-up;
+	};
+};
+
 &sdc1_on {
 	clk {
 		bias-disable;
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V5 4/7] arm64: dts: sc7280: Update QUPv3 UART5 DT node

From: Rajesh Patil <hidden>
Date: 2021-08-12 07:42:53 

From: Roja Rani Yarubandi <redacted>

Update the compatible string as "qcom,geni-uart".
Add interconnects and power-domains. Split the pinctrl
functions and correct the gpio pins.

Signed-off-by: Roja Rani Yarubandi <redacted>
Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 30 +++++++++++++++++++++++++-----
 1 file changed, 25 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index e461395..2dc7e8c 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -861,13 +861,18 @@
 			};
 
 			uart5: serial@994000 {
-				compatible = "qcom,geni-debug-uart";
+				compatible = "qcom,geni-uart";
 				reg = <0 0x00994000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
 				pinctrl-names = "default";
-				pinctrl-0 = <&qup_uart5_default>;
+				pinctrl-0 = <&qup_uart5_cts>, <&qup_uart5_rts>, <&qup_uart5_tx>, <&qup_uart5_rx>;
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
 				status = "disabled";
 			};
 
@@ -2255,9 +2260,24 @@
 				function = "qup04";
 			};
 
-			qup_uart5_default: qup-uart5-default {
-				pins = "gpio46", "gpio47";
-				function = "qup13";
+			qup_uart5_cts: qup-uart5-cts {
+				pins = "gpio20";
+				function = "qup05";
+			};
+
+			qup_uart5_rts: qup-uart5-rts {
+				pins = "gpio21";
+				function = "qup05";
+			};
+
+			qup_uart5_tx: qup-uart5-tx {
+				pins = "gpio22";
+				function = "qup05";
+			};
+
+			qup_uart5_rx: qup-uart5-rx {
+				pins = "gpio23";
+				function = "qup05";
 			};
 
 			qup_uart6_cts: qup-uart6-cts {
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V5 7/7] arm64: dts: sc7280: Add QUPv3 wrapper_1 nodes

From: Rajesh Patil <hidden>
Date: 2021-08-12 07:42:56 

From: Roja Rani Yarubandi <redacted>

Add QUPv3 wrapper_1 DT nodes for SC7280 SoC.

Signed-off-by: Roja Rani Yarubandi <redacted>
Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi |   4 +
 arch/arm64/boot/dts/qcom/sc7280.dtsi     | 749 +++++++++++++++++++++++++++++++
 2 files changed, 753 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 7c106c0..65126a7 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -225,6 +225,10 @@
 	status = "okay";
 };
 
+&qupv3_id_1 {
+	status = "okay";
+};
+
 &sdhc_1 {
 	status = "okay";
 
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 2dc7e8c..e29af91 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -981,6 +981,435 @@
 			};
 		};
 
+		qupv3_id_1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0 0x00ac0000 0 0x2000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			iommus = <&apps_smmu 0x43 0x0>;
+			status = "disabled";
+
+			i2c8: i2c@a80000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a80000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c8_data_clk>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi8: spi@a80000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a80000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>, <&qup_spi8_cs_gpio>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart8: serial@a80000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a80000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart8_cts>, <&qup_uart8_rts>, <&qup_uart8_tx>, <&qup_uart8_rx>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c9: i2c@a84000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a84000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c9_data_clk>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi9: spi@a84000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a84000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>, <&qup_spi9_cs_gpio>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart9: serial@a84000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a84000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart9_cts>, <&qup_uart9_rts>, <&qup_uart9_tx>, <&qup_uart9_rx>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c10: i2c@a88000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a88000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c10_data_clk>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi10: spi@a88000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a88000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>, <&qup_spi10_cs_gpio>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart10: serial@a88000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a88000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart10_cts>, <&qup_uart10_rts>, <&qup_uart10_tx>, <&qup_uart10_rx>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c11: i2c@a8c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a8c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c11_data_clk>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi11: spi@a8c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a8c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>, <&qup_spi11_cs_gpio>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart11: serial@a8c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a8c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart11_cts>, <&qup_uart11_rts>, <&qup_uart11_tx>, <&qup_uart11_rx>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c12: i2c@a90000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a90000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c12_data_clk>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi12: spi@a90000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a90000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>, <&qup_spi12_cs_gpio>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart12: serial@a90000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a90000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart12_cts>, <&qup_uart12_rts>, <&qup_uart12_tx>, <&qup_uart12_rx>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c13: i2c@a94000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a94000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c13_data_clk>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi13: spi@a94000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a94000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>, <&qup_spi13_cs_gpio>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart13: serial@a94000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a94000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart13_cts>, <&qup_uart13_rts>, <&qup_uart13_tx>, <&qup_uart13_rx>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c14: i2c@a98000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a98000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c14_data_clk>;
+				interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi14: spi@a98000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a98000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>, <&qup_spi14_cs_gpio>;
+				interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart14: serial@a98000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a98000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart14_cts>, <&qup_uart14_rts>, <&qup_uart14_tx>, <&qup_uart14_rx>;
+				interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c15: i2c@a9c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a9c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c15_data_clk>;
+				interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi15: spi@a9c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a9c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>, <&qup_spi15_cs_gpio>;
+				interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart15: serial@a9c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a9c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart15_cts>, <&qup_uart15_rts>, <&qup_uart15_tx>, <&qup_uart15_rx>;
+				interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+		};
+
 		cnoc2: interconnect@1500000 {
 			reg = <0 0x01500000 0 0x1000>;
 			compatible = "qcom,sc7280-cnoc2";
@@ -2040,6 +2469,46 @@
 				function = "qup07";
 			};
 
+			qup_i2c8_data_clk:qup-i2c8-data-clk {
+				pins = "gpio32", "gpio33";
+				function = "qup10";
+			};
+
+			qup_i2c9_data_clk:qup-i2c9-data-clk {
+				pins = "gpio36", "gpio37";
+				function = "qup11";
+			};
+
+			qup_i2c10_data_clk:qup-i2c10-data-clk {
+				pins = "gpio40", "gpio41";
+				function = "qup12";
+			};
+
+			qup_i2c11_data_clk:qup-i2c11-data-clk {
+				pins = "gpio44", "gpio45";
+				function = "qup13";
+			};
+
+			qup_i2c12_data_clk:qup-i2c12-data-clk {
+				pins = "gpio48", "gpio49";
+				function = "qup14";
+			};
+
+			qup_i2c13_data_clk:qup-i2c13-data-clk {
+				pins = "gpio52", "gpio53";
+				function = "qup15";
+			};
+
+			qup_i2c14_data_clk:qup-i2c14-data-clk {
+				pins = "gpio56", "gpio57";
+				function = "qup16";
+			};
+
+			qup_i2c15_data_clk:qup-i2c15-data-clk {
+				pins = "gpio60", "gpio61";
+				function = "qup17";
+			};
+
 			qup_spi0_data_clk: qup-spi0-data-clk {
 				pins = "gpio0", "gpio1", "gpio2";
 				function = "qup00";
@@ -2160,6 +2629,126 @@
 				function = "gpio";
 			};
 
+			qup_spi8_data_clk: qup-spi8-data-clk {
+				pins = "gpio32", "gpio33", "gpio34";
+				function = "qup10";
+			};
+
+			qup_spi8_cs: qup-spi8-cs {
+				pins = "gpio35";
+				function = "qup10";
+			};
+
+			qup_spi8_cs_gpio: qup-spi8-cs_gpio {
+				pins = "gpio35";
+				function = "gpio";
+			};
+
+			qup_spi9_data_clk: qup-spi9-data-clk {
+				pins = "gpio36", "gpio37", "gpio38";
+				function = "qup11";
+			};
+
+			qup_spi9_cs: qup-spi9-cs {
+				pins = "gpio39";
+				function = "qup11";
+			};
+
+			qup_spi9_cs_gpio: qup-spi9-cs_gpio {
+				pins = "gpio39";
+				function = "gpio";
+			};
+
+			qup_spi10_data_clk: qup-spi10-data-clk {
+				pins = "gpio40", "gpio41", "gpio42";
+				function = "qup12";
+			};
+
+			qup_spi10_cs: qup-spi10-cs {
+				pins = "gpio43";
+				function = "qup12";
+			};
+
+			qup_spi10_cs_gpio: qup-spi10-cs_gpio {
+				pins = "gpio43";
+				function = "gpio";
+			};
+
+			qup_spi11_data_clk: qup-spi11-data-clk {
+				pins = "gpio44", "gpio45", "gpio46";
+				function = "qup13";
+			};
+
+			qup_spi11_cs: qup-spi11-cs {
+				pins = "gpio47";
+				function = "qup13";
+			};
+
+			qup_spi11_cs_gpio: qup-spi11-cs_gpio {
+				pins = "gpio47";
+				function = "gpio";
+			};
+
+			qup_spi12_data_clk: qup-spi12-data-clk {
+				pins = "gpio48", "gpio49", "gpio50";
+				function = "qup14";
+			};
+
+			qup_spi12_cs: qup-spi12-cs {
+				pins = "gpio51";
+				function = "qup14";
+			};
+
+			qup_spi12_cs_gpio: qup-spi12-cs_gpio {
+				pins = "gpio51";
+				function = "gpio";
+			};
+
+			qup_spi13_data_clk: qup-spi13-data-clk {
+				pins = "gpio52", "gpio53", "gpio54";
+				function = "qup15";
+			};
+
+			qup_spi13_cs: qup-spi13-cs {
+				pins = "gpio55";
+				function = "qup15";
+			};
+
+			qup_spi13_cs_gpio: qup-spi13-cs_gpio {
+				pins = "gpio55";
+				function = "gpio";
+			};
+
+			qup_spi14_data_clk: qup-spi14-data-clk {
+				pins = "gpio56", "gpio57", "gpio58";
+				function = "qup16";
+			};
+
+			qup_spi14_cs: qup-spi14-cs {
+				pins = "gpio59";
+				function = "qup16";
+			};
+
+			qup_spi14_cs_gpio: qup-spi14-cs_gpio {
+				pins = "gpio59";
+				function = "gpio";
+			};
+
+			qup_spi15_data_clk: qup-spi15-data-clk {
+				pins = "gpio60", "gpio61", "gpio62";
+				function = "qup17";
+			};
+
+			qup_spi15_cs: qup-spi15-cs {
+				pins = "gpio63";
+				function = "qup17";
+			};
+
+			qup_spi15_cs_gpio: qup-spi15-cs_gpio {
+				pins = "gpio63";
+				function = "gpio";
+			};
+
 			qup_uart0_cts: qup-uart0-cts {
 				pins = "gpio0";
 				function = "qup00";
@@ -2400,6 +2989,166 @@
 					bias-bus-hold;
 				};
 			};
+
+			qup_uart8_cts: qup-uart8-cts {
+				pins = "gpio32";
+				function = "qup10";
+			};
+
+			qup_uart8_rts: qup-uart8-rts {
+				pins = "gpio33";
+				function = "qup10";
+			};
+
+			qup_uart8_tx: qup-uart8-tx {
+				pins = "gpio34";
+				function = "qup10";
+			};
+
+			qup_uart8_rx: qup-uart8-rx {
+				pins = "gpio35";
+				function = "qup10";
+			};
+
+			qup_uart9_cts: qup-uart9-cts {
+				pins = "gpio36";
+				function = "qup11";
+			};
+
+			qup_uart9_rts: qup-uart9-rts {
+				pins = "gpio37";
+				function = "qup11";
+			};
+
+			qup_uart9_tx: qup-uart9-tx {
+				pins = "gpio38";
+				function = "qup11";
+			};
+
+			qup_uart9_rx: qup-uart9-rx {
+				pins = "gpio39";
+				function = "qup11";
+			};
+
+			qup_uart10_cts: qup-uart10-cts {
+				pins = "gpio40";
+				function = "qup12";
+			};
+
+			qup_uart10_rts: qup-uart10-rts {
+				pins = "gpio41";
+				function = "qup12";
+			};
+
+			qup_uart10_tx: qup-uart10-tx {
+				pins = "gpio42";
+				function = "qup12";
+			};
+
+			qup_uart10_rx: qup-uart10-rx {
+				pins = "gpio43";
+				function = "qup12";
+			};
+
+			qup_uart11_cts: qup-uart11-cts {
+				pins = "gpio44";
+				function = "qup13";
+			};
+
+			qup_uart11_rts: qup-uart11-rts {
+				pins = "gpio45";
+				function = "qup13";
+			};
+
+			qup_uart11_tx: qup-uart11-tx {
+				pins = "gpio46";
+				function = "qup13";
+			};
+
+			qup_uart11_rx: qup-uart11-rx {
+				pins = "gpio47";
+				function = "qup13";
+			};
+
+			qup_uart12_cts: qup-uart12-cts {
+				pins = "gpio48";
+				function = "qup14";
+			};
+
+			qup_uart12_rts: qup-uart12-rts {
+				pins = "gpio49";
+				function = "qup14";
+			};
+
+			qup_uart12_tx: qup-uart12-tx {
+				pins = "gpio50";
+				function = "qup14";
+			};
+
+			qup_uart12_rx: qup-uart12-rx {
+				pins = "gpio51";
+				function = "qup14";
+			};
+
+			qup_uart13_cts: qup-uart13-cts {
+				pins = "gpio52";
+				function = "qup15";
+			};
+
+			qup_uart13_rts: qup-uart13-rts {
+				pins = "gpio53";
+				function = "qup15";
+			};
+
+			qup_uart13_tx: qup-uart13-tx {
+				pins = "gpio54";
+				function = "qup15";
+			};
+
+			qup_uart13_rx: qup-uart13-rx {
+				pins = "gpio55";
+				function = "qup15";
+			};
+
+			qup_uart14_cts: qup-uart14-cts {
+				pins = "gpio56";
+				function = "qup16";
+			};
+
+			qup_uart14_rts: qup-uart14-rts {
+				pins = "gpio57";
+				function = "qup16";
+			};
+
+			qup_uart14_tx: qup-uart14-tx {
+				pins = "gpio58";
+				function = "qup16";
+			};
+
+			qup_uart14_rx: qup-uart14-rx {
+				pins = "gpio59";
+				function = "qup16";
+			};
+
+			qup_uart15_cts: qup-uart15-cts {
+				pins = "gpio60";
+				function = "qup17";
+			};
+
+			qup_uart15_rts: qup-uart15-rts {
+				pins = "gpio61";
+				function = "qup17";
+			};
+
+			qup_uart15_tx: qup-uart15-tx {
+				pins = "gpio62";
+				function = "qup17";
+			};
+
+			qup_uart15_rx: qup-uart15-rx {
+				pins = "gpio63";
+				function = "qup17";
+			};
 		};
 
 		apps_smmu: iommu@15000000 {
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V5 2/7] arm64: dts: sc7280: Configure SPI-NOR FLASH for sc7280-idp

From: Rajesh Patil <hidden>
Date: 2021-08-12 07:42:58 

Add spi-nor flash node and pinctrl configurations for the same.

Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 371a2a9..c41c2d0 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -207,6 +207,20 @@
 	};
 };
 
+&qspi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <37500000>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+	};
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
@@ -284,6 +298,19 @@
 
 /* PINCTRL - additions to nodes defined in sc7280.dtsi */
 
+&qspi_cs0 {
+	bias-disable;
+};
+
+&qspi_clk {
+	bias-disable;
+};
+
+&qspi_data01 {
+	/* High-Z when no transfers; nice to park the lines */
+	bias-pull-up;
+};
+
 &qup_uart5_default {
 	tx {
 		pins = "gpio46";
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V5 5/7] arm64: dts: sc7280: Configure debug uart for sc7280-idp

From: Rajesh Patil <hidden>
Date: 2021-08-12 07:42:59 

Configure uart5 as debug uart and split the pinctrl functions
to match with SoC dt.

Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 19 ++++++++-----------
 1 file changed, 8 insertions(+), 11 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index c41c2d0..53993b3 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -254,6 +254,7 @@
 };
 
 &uart5 {
+	compatible = "qcom,geni-debug-uart";
 	status = "okay";
 };
 
@@ -311,18 +312,14 @@
 	bias-pull-up;
 };
 
-&qup_uart5_default {
-	tx {
-		pins = "gpio46";
-		drive-strength = <2>;
-		bias-disable;
-	};
+&qup_uart5_tx {
+	drive-strength = <2>;
+	bias-disable;
+};
 
-	rx {
-		pins = "gpio47";
-		drive-strength = <2>;
-		bias-pull-up;
-	};
+&qup_uart5_rx {
+	drive-strength = <2>;
+	bias-pull-up;
 };
 
 &sdc1_on {
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V5 1/7] arm64: dts: sc7280: Add QSPI node

From: Rajesh Patil <hidden>
Date: 2021-08-12 07:43:03 

From: Roja Rani Yarubandi <redacted>

Add QSPI DT node and qspi_opp_table for SC7280 SoC.

Signed-off-by: Roja Rani Yarubandi <redacted>
Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 62 ++++++++++++++++++++++++++++++++++++
 1 file changed, 62 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 53a21d0..f8dd5ff 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -415,6 +415,25 @@
 		method = "smc";
 	};
 
+	qspi_opp_table: qspi-opp-table {
+		compatible = "operating-points-v2";
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-150000000 {
+			opp-hz = /bits/ 64 <150000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+	};
+
 	soc: soc@0 {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -1318,6 +1337,24 @@
 			};
 		};
 
+		qspi: spi@88dc000 {
+			compatible = "qcom,qspi-v1";
+			reg = <0 0x088dc000 0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+				 <&gcc GCC_QSPI_CORE_CLK>;
+			clock-names = "iface", "core";
+			interconnects = <&gem_noc MASTER_APPSS_PROC 0
+					&cnoc2 SLAVE_QSPI_0 0>;
+			interconnect-names = "qspi-config";
+			power-domains = <&rpmhpd SC7280_CX>;
+			operating-points-v2 = <&qspi_opp_table>;
+			status = "disabled";
+
+		};
+
 		dc_noc: interconnect@90e0000 {
 			reg = <0 0x090e0000 0 0x5080>;
 			compatible = "qcom,sc7280-dc-noc";
@@ -1513,6 +1550,31 @@
 			gpio-ranges = <&tlmm 0 0 175>;
 			wakeup-parent = <&pdc>;
 
+			qspi_clk: qspi-clk {
+				pins = "gpio14";
+				function = "qspi_clk";
+			};
+
+			qspi_cs0: qspi-cs0 {
+				pins = "gpio15";
+				function = "qspi_cs";
+			};
+
+			qspi_cs1: qspi-cs1 {
+				pins = "gpio19";
+				function = "qspi_cs";
+			};
+
+			qspi_data01: qspi-data01 {
+				pins = "gpio12", "gpio13";
+				function = "qspi_data";
+			};
+
+			qspi_data12: qspi-data12 {
+				pins = "gpio16", "gpio17";
+				function = "qspi_data";
+			};
+
 			qup_uart5_default: qup-uart5-default {
 				pins = "gpio46", "gpio47";
 				function = "qup13";
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

Re: [PATCH V5 1/7] arm64: dts: sc7280: Add QSPI node

From: Matthias Kaehlcke <mka@chromium.org>
Date: 2021-08-12 13:09:11 

On Thu, Aug 12, 2021 at 01:11:12PM +0530, Rajesh Patil wrote:
quoted hunk
From: Roja Rani Yarubandi <redacted>

Add QSPI DT node and qspi_opp_table for SC7280 SoC.

Signed-off-by: Roja Rani Yarubandi <redacted>
Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 62 ++++++++++++++++++++++++++++++++++++
 1 file changed, 62 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 53a21d0..f8dd5ff 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -415,6 +415,25 @@
 		method = "smc";
 	};
 
+	qspi_opp_table: qspi-opp-table {
+		compatible = "operating-points-v2";
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-150000000 {
+			opp-hz = /bits/ 64 <150000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+	};
+
From v3:

roja> Can we move this "qspi_opp_table" to / from /soc?

bjorn> If you have made a proper attempt to convince Rob and Mark that
bjorn> a child "opp-table" in a SPI master is not a SPI device - and the
bjorn> conclusion is that this is not a good idea...then yes it should live
bjorn> outside /soc.

I didn't see a follow up on this, was such an attempt made? Is there a
link to the discussion?

Re: [PATCH V5 2/7] arm64: dts: sc7280: Configure SPI-NOR FLASH for sc7280-idp

From: Matthias Kaehlcke <mka@chromium.org>
Date: 2021-08-12 13:15:12 

On Thu, Aug 12, 2021 at 01:11:13PM +0530, Rajesh Patil wrote:
Add spi-nor flash node and pinctrl configurations for the same.
nit: better name SC7280 IDP explicitly rather than saying 'the same'.

Signed-off-by: Rajesh Patil <redacted>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH V5 3/7] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes

From: Matthias Kaehlcke <mka@chromium.org>
Date: 2021-08-12 14:14:13 

On Thu, Aug 12, 2021 at 01:11:14PM +0530, Rajesh Patil wrote:
quoted hunk
From: Roja Rani Yarubandi <redacted>

Add QUPv3 wrapper_0 DT nodes for SC7280 SoC.

Signed-off-by: Roja Rani Yarubandi <redacted>
Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 720 +++++++++++++++++++++++++++++++++++
 1 file changed, 720 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index f8dd5ff..e461395 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -533,6 +533,25 @@
 
 		};
 
+		qup_opp_table: qup-opp-table {
+			compatible = "operating-points-v2";
+
+			opp-75000000 {
+				opp-hz = /bits/ 64 <75000000>;
+				required-opps = <&rpmhpd_opp_low_svs>;
+			};
+
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+				required-opps = <&rpmhpd_opp_svs>;
+			};
+
+			opp-128000000 {
+				opp-hz = /bits/ 64 <128000000>;
+				required-opps = <&rpmhpd_opp_nom>;
+			};
+		};
+
Shouldn't the OPP table live outside of /soc, analogous to the discussion
about the QSPI OPP table (https://lkml.org/lkml/2021/7/19/3063)?
quoted hunk
 		qupv3_id_0: geniqup@9c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0 0x009c0000 0 0x2000>;
@@ -542,8 +561,305 @@
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
+			iommus = <&apps_smmu 0x123 0x0>;
 			status = "disabled";
 
+			i2c0: i2c@980000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
nit: the general convention seems to be 'clocks' followed by 'clock-names'.
Applicable to all nodes if you decide to change it.
quoted hunk
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c0_data_clk>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi0: spi@980000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>, <&qup_spi0_cs_gpio>;
What is the story behind 'qup_spiN_cs' and 'qup_spiN_cs_gpio'? Both configure
the CS pin with a different function:

  qup_spi0_cs: qup-spi0-cs {
  	pins = "gpio3";
  	function = "qup00";
  };

  qup_spi0_cs_gpio: qup-spi0-cs_gpio {
  	pins = "gpio3";
  	function = "gpio";
  };
quoted hunk
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart0: serial@980000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart0_cts>, <&qup_uart0_rts>, <&qup_uart0_tx>, <&qup_uart0_rx>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c1: i2c@984000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00984000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c1_data_clk>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;

364 more quoted lines

  > +			qup_i2c3_data_clk:qup-i2c3-data-clk {
quoted hunk
+				pins = "gpio12", "gpio13";
+				function = "qup03";
+			};
+
+			qup_i2c4_data_clk:qup-i2c4-data-clk {
+				pins = "gpio16", "gpio17";
+				function = "qup04";
+			};
+
+			qup_i2c5_data_clk:qup-i2c5-data-clk {
+				pins = "gpio20", "gpio21";
+				function = "qup05";
+			};
+
+			qup_i2c6_data_clk:qup-i2c6-data-clk {
+				pins = "gpio24", "gpio25";
+				function = "qup06";
+			};
+
+			qup_i2c7_data_clk:qup-i2c7-data-clk {
+				pins = "gpio28", "gpio29";
+				function = "qup07";
+			};
+
+			qup_spi0_data_clk: qup-spi0-data-clk {
+				pins = "gpio0", "gpio1", "gpio2";
+				function = "qup00";
+			};
+
+			qup_spi0_cs: qup-spi0-cs {
+				pins = "gpio3";
+				function = "qup00";
+			};
+
+			qup_spi0_cs_gpio: qup-spi0-cs_gpio {
+				pins = "gpio3";
+				function = "gpio";
+			};
+
+			qup_spi1_data_clk: qup-spi1-data-clk {

208 more quoted lines

Wait, why does uart5 use the pins of qup13? Is see this is
'fixed' by '[4/7] arm64: dts: sc7280: Update QUPv3 UART5 DT
node' but I'm still surprised ...

Doesn't 'fixing' this break devices that are currently using
'uart5'? It seems those devices would need to change from
'uart5' to 'uart11'.

Re: [PATCH V5 4/7] arm64: dts: sc7280: Update QUPv3 UART5 DT node

From: Matthias Kaehlcke <mka@chromium.org>
Date: 2021-08-12 15:46:10 

On Thu, Aug 12, 2021 at 01:11:15PM +0530, Rajesh Patil wrote:
quoted hunk
From: Roja Rani Yarubandi <redacted>

Update the compatible string as "qcom,geni-uart".
Add interconnects and power-domains. Split the pinctrl
functions and correct the gpio pins.

Signed-off-by: Roja Rani Yarubandi <redacted>
Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 30 +++++++++++++++++++++++++-----
 1 file changed, 25 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index e461395..2dc7e8c 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -861,13 +861,18 @@
 			};
 
 			uart5: serial@994000 {
-				compatible = "qcom,geni-debug-uart";
+				compatible = "qcom,geni-uart";
 				reg = <0 0x00994000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
 				pinctrl-names = "default";
-				pinctrl-0 = <&qup_uart5_default>;
+				pinctrl-0 = <&qup_uart5_cts>, <&qup_uart5_rts>, <&qup_uart5_tx>, <&qup_uart5_rx>;
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
 				status = "disabled";
 			};
 
@@ -2255,9 +2260,24 @@
 				function = "qup04";
 			};

4 more quoted lines

sc7280-idp.dtsi references this node, so if this patch is applied the SC7280
IDP DT would be broken, unless "[5/7] arm64: dts: sc7280: Configure debug
uart for sc7280-idp" is also applied. I think you need to squash the two
patches.

Re: [PATCH V5 5/7] arm64: dts: sc7280: Configure debug uart for sc7280-idp

From: Matthias Kaehlcke <mka@chromium.org>
Date: 2021-08-12 16:05:56 

On Thu, Aug 12, 2021 at 01:11:16PM +0530, Rajesh Patil wrote:
Configure uart5 as debug uart and split the pinctrl functions
to match with SoC dt.

Signed-off-by: Rajesh Patil <redacted>
As I mentioned on '[4/7] arm64: dts: sc7280: Update QUPv3 UART5 DT node',
I think you need to squash the two patches to avoid breaking (temporarily)
the SC7280 IDP DT due to the undefined node 'qup_uart5_default'

Re: [PATCH V5 3/7] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes

From: Matthias Kaehlcke <mka@chromium.org>
Date: 2021-08-12 16:22:37 

On Thu, Aug 12, 2021 at 07:14:07AM -0700, Matthias Kaehlcke wrote:
On Thu, Aug 12, 2021 at 01:11:14PM +0530, Rajesh Patil wrote:
quoted
 			qup_uart5_default: qup-uart5-default {
 				pins = "gpio46", "gpio47";
 				function = "qup13";
 			};
Wait, why does uart5 use the pins of qup13? Is see this is
'fixed' by '[4/7] arm64: dts: sc7280: Update QUPv3 UART5 DT
node' but I'm still surprised ...

Doesn't 'fixing' this break devices that are currently using
'uart5'? It seems those devices would need to change from
'uart5' to 'uart11'.
Apparently the above configuration is bogus. I checked the schematic
of the IDP which uses uart5, the debug UART is on pins 22 and 23, aka
qup05. It seems uart5 works in spite of the bogus pinconf because the
default for the pins is their QUP function.





  

    
Re: [PATCH V5 6/7] arm64: dts: sc7280: Configure uart7 to support bluetooth on sc7280-idp

    

      From: Matthias Kaehlcke <mka@chromium.org>

      Date: 2021-08-12 19:22:43 
    

  

  
On Thu, Aug 12, 2021 at 01:11:17PM +0530, Rajesh Patil wrote:
Add bluetooth uart pin configuration for sc7280-idp.

Signed-off-by: Rajesh Patil <redacted>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>





  

    
Re: [PATCH V5 3/7] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes

    

      From: Doug Anderson <dianders@chromium.org>

      Date: 2021-08-19 00:04:39 
    

  

  
Hi,

On Thu, Aug 12, 2021 at 12:42 AM Rajesh Patil [off-list ref] wrote:
quoted hunk
@@ -542,8 +561,305 @@
                        #address-cells = <2>;
                        #size-cells = <2>;
                        ranges;
+                       iommus = <&apps_smmu 0x123 0x0>;
                        status = "disabled";

+                       i2c0: i2c@980000 {
Not a full review of your patch (I think Matthias has already looked
in a bunch of detail), but can I also request that you add i2c and spi
aliases in your next spin (I think you have to spin this anyway,
right?) Add these under the "aliases" mode before the mmc ones (to
keep sort order good):

i2c0 = &i2c0;
i2c1 = &i2c1;
i2c2 = &i2c2;
i2c3 = &i2c3;
i2c4 = &i2c4;
i2c5 = &i2c5;
i2c6 = &i2c6;
i2c7 = &i2c7;
i2c8 = &i2c8;
i2c9 = &i2c9;
i2c10 = &i2c10;
i2c11 = &i2c11;
i2c12 = &i2c12;
i2c13 = &i2c13;
i2c14 = &i2c14;
i2c15 = &i2c15;

...and these after:

spi0 = &spi0;
spi1 = &spi1;
spi2 = &spi2;
spi3 = &spi3;
spi4 = &spi4;
spi5 = &spi5;
spi6 = &spi6;
spi7 = &spi7;
spi8 = &spi8;
spi9 = &spi9;
spi10 = &spi10;
spi11 = &spi11;
spi12 = &spi12;
spi13 = &spi13;
10 more lines





  

    
Re: [PATCH V5 2/7] arm64: dts: sc7280: Configure SPI-NOR FLASH for sc7280-idp

    

      From: <hidden>

      Date: 2021-08-23 11:44:13 
    

  

  
On 2021-08-12 18:45, Matthias Kaehlcke wrote:
On Thu, Aug 12, 2021 at 01:11:13PM +0530, Rajesh Patil wrote:
quoted
Add spi-nor flash node and pinctrl configurations for the same.
nit: better name SC7280 IDP explicitly rather than saying 'the same'.
ok.I will change it

quoted
Signed-off-by: Rajesh Patil <redacted>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>





  

    
Re: [PATCH V5 3/7] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes

    

      From: <hidden>

      Date: 2021-08-26 12:53:50 
    

  

  
On 2021-08-19 05:34, Doug Anderson wrote:
Hi,

On Thu, Aug 12, 2021 at 12:42 AM Rajesh Patil [off-list ref] wrote:
quoted
@@ -542,8 +561,305 @@
                        #address-cells = <2>;
                        #size-cells = <2>;
                        ranges;
+                       iommus = <&apps_smmu 0x123 0x0>;
                        status = "disabled";

+                       i2c0: i2c@980000 {
Not a full review of your patch (I think Matthias has already looked
in a bunch of detail), but can I also request that you add i2c and spi
aliases in your next spin (I think you have to spin this anyway,
right?) Add these under the "aliases" mode before the mmc ones (to
keep sort order good):
ok I will add them.

Thanks
Rajesh

i2c0 = &i2c0;
i2c1 = &i2c1;
i2c2 = &i2c2;
i2c3 = &i2c3;
i2c4 = &i2c4;
i2c5 = &i2c5;
i2c6 = &i2c6;
i2c7 = &i2c7;
i2c8 = &i2c8;
i2c9 = &i2c9;
i2c10 = &i2c10;
i2c11 = &i2c11;
i2c12 = &i2c12;
i2c13 = &i2c13;
i2c14 = &i2c14;
i2c15 = &i2c15;

...and these after:

spi0 = &spi0;
spi1 = &spi1;
spi2 = &spi2;
spi3 = &spi3;
spi4 = &spi4;
spi5 = &spi5;
spi6 = &spi6;
spi7 = &spi7;
spi8 = &spi8;
spi9 = &spi9;
spi10 = &spi10;
spi11 = &spi11;
spi12 = &spi12;
spi13 = &spi13;
spi14 = &spi14;
spi15 = &spi15;

The "Quad SPI" doesn't get an alias, but that's OK. It doesn't have a
well-defined number in the manual and it's fine to have it be
auto-assigned. It's really just confusing when there's something with
a well-defined number in the manual and it's a _different_ one in the
3 more quoted lines





  

    
Re: [PATCH V5 1/7] arm64: dts: sc7280: Add QSPI node

    

      From: <hidden>

      Date: 2021-08-26 12:59:45 
    

  

  
On 2021-08-12 18:39, Matthias Kaehlcke wrote:
On Thu, Aug 12, 2021 at 01:11:12PM +0530, Rajesh Patil wrote:
quoted
From: Roja Rani Yarubandi <redacted>

Add QSPI DT node and qspi_opp_table for SC7280 SoC.

Signed-off-by: Roja Rani Yarubandi <redacted>
Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 62 ++++++++++++++++++++++++++++++++++++
 1 file changed, 62 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 53a21d0..f8dd5ff 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -415,6 +415,25 @@
 		method = "smc";
 	};

+	qspi_opp_table: qspi-opp-table {
+		compatible = "operating-points-v2";
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-150000000 {
+			opp-hz = /bits/ 64 <150000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+	};
+
From v3:
10 more quoted lines
For now I am keeping qspi_opp_table  and qup_opp_table outside the SoC and posting V6.
I will continue the discussion with DT folks and once concluded I will update as required.





  

    
Re: [PATCH V5 3/7] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes

    

      From: <hidden>

      Date: 2021-08-26 13:07:09 
    

  

  
On 2021-08-12 19:44, Matthias Kaehlcke wrote:
On Thu, Aug 12, 2021 at 01:11:14PM +0530, Rajesh Patil wrote:
quoted
From: Roja Rani Yarubandi <redacted>

Add QUPv3 wrapper_0 DT nodes for SC7280 SoC.

Signed-off-by: Roja Rani Yarubandi <redacted>
Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 720 +++++++++++++++++++++++++++++++++++
 1 file changed, 720 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index f8dd5ff..e461395 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -533,6 +533,25 @@

 		};

+		qup_opp_table: qup-opp-table {
+			compatible = "operating-points-v2";
+
+			opp-75000000 {
+				opp-hz = /bits/ 64 <75000000>;
+				required-opps = <&rpmhpd_opp_low_svs>;
+			};
+
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+				required-opps = <&rpmhpd_opp_svs>;
+			};
+
+			opp-128000000 {
+				opp-hz = /bits/ 64 <128000000>;
+				required-opps = <&rpmhpd_opp_nom>;
+			};
+		};
+
Shouldn't the OPP table live outside of /soc, analogous to the discussion
1 more quoted lines
Ok

quoted
 		qupv3_id_0: geniqup@9c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0 0x009c0000 0 0x2000>;
@@ -542,8 +561,305 @@
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
+			iommus = <&apps_smmu 0x123 0x0>;
 			status = "disabled";

+			i2c0: i2c@980000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
nit: the general convention seems to be 'clocks' followed by 'clock-names'.
Applicable to all nodes if you decide to change it.
Ok

quoted
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c0_data_clk>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi0: spi@980000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>, <&qup_spi0_cs_gpio>;
What is the story behind 'qup_spiN_cs' and 'qup_spiN_cs_gpio'? Both configure
the CS pin with a different function:
As per discussion here [1], we have split like this.

[1] https://lore.kernel.org/patchwork/patch/1393353/#1591826


  qup_spi0_cs: qup-spi0-cs {
  	pins = "gpio3";
  	function = "qup00";
  };

  qup_spi0_cs_gpio: qup-spi0-cs_gpio {
  	pins = "gpio3";
  	function = "gpio";
  };

quoted
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart0: serial@980000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart0_cts>, <&qup_uart0_rts>, <&qup_uart0_tx>, <&qup_uart0_rx>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c1: i2c@984000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00984000 0 0x4000>;
631 more quoted lines





  

    
Re: [PATCH V5 5/7] arm64: dts: sc7280: Configure debug uart for sc7280-idp

    

      From: <hidden>

      Date: 2021-08-26 13:08:39 
    

  

  
On 2021-08-12 21:35, Matthias Kaehlcke wrote:
On Thu, Aug 12, 2021 at 01:11:16PM +0530, Rajesh Patil wrote:
quoted
Configure uart5 as debug uart and split the pinctrl functions
to match with SoC dt.

Signed-off-by: Rajesh Patil <redacted>
As I mentioned on '[4/7] arm64: dts: sc7280: Update QUPv3 UART5 DT node',
I think you need to squash the two patches to avoid breaking (temporarily)
the SC7280 IDP DT due to the undefined node 'qup_uart5_default'
Okay





  

    
Re: [PATCH V5 3/7] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes

    

      From: Matthias Kaehlcke <mka@chromium.org>

      Date: 2021-08-26 19:51:39 
    

  

  
On Thu, Aug 26, 2021 at 06:37:02PM +0530, rajpat@codeaurora.org wrote:
On 2021-08-12 19:44, Matthias Kaehlcke wrote:
quoted
On Thu, Aug 12, 2021 at 01:11:14PM +0530, Rajesh Patil wrote:
quoted
From: Roja Rani Yarubandi <redacted>

Add QUPv3 wrapper_0 DT nodes for SC7280 SoC.

Signed-off-by: Roja Rani Yarubandi <redacted>
Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 720
+++++++++++++++++++++++++++++++++++
 1 file changed, 720 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi
b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index f8dd5ff..e461395 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi

...

+			spi0: spi@980000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>,
<&qup_spi0_cs_gpio>;
What is the story behind 'qup_spiN_cs' and 'qup_spiN_cs_gpio'? Both
configure
the CS pin with a different function:
As per discussion here [1], we have split like this.

[1] https://lore.kernel.org/patchwork/patch/1393353/#1591826
IIUC that's only about having separate configs for each pin, instead of
groups like 'qup-spi0-default'. What you are doing above with 'qup_spi0_cs'
and 'qup_spi0_cs_gpio' is to configure the same pin (GPIO 3) both as SPI
chip select and as GPIO. Which one is it?

I imagine we want to have both pinctrl definitions to allow a board to
configure the pin either as SPI CS or GPIO. However it should be only one
of the two at a time, and the SoC .dtsi should provide a reasonable
default, which probably is SPI CS.

Maybe I'm missing something, if so please provide details on why it is
necessary to have this config.





  

    
Re: [PATCH V5 3/7] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes

    

      From: <hidden>

      Date: 2021-09-01 07:07:13 
    

  

  
On 2021-08-27 01:21, Matthias Kaehlcke wrote:
On Thu, Aug 26, 2021 at 06:37:02PM +0530, rajpat@codeaurora.org wrote:
quoted
On 2021-08-12 19:44, Matthias Kaehlcke wrote:
quoted
On Thu, Aug 12, 2021 at 01:11:14PM +0530, Rajesh Patil wrote:
quoted
From: Roja Rani Yarubandi <redacted>

Add QUPv3 wrapper_0 DT nodes for SC7280 SoC.

Signed-off-by: Roja Rani Yarubandi <redacted>
Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 720
+++++++++++++++++++++++++++++++++++
 1 file changed, 720 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi
b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index f8dd5ff..e461395 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi

...

+			spi0: spi@980000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>,
<&qup_spi0_cs_gpio>;
What is the story behind 'qup_spiN_cs' and 'qup_spiN_cs_gpio'? Both
configure
the CS pin with a different function:
As per discussion here [1], we have split like this.

[1] https://lore.kernel.org/patchwork/patch/1393353/#1591826
10 more quoted lines
I agree. Will remove it in next version.

Maybe I'm missing something, if so please provide details on why it is
necessary to have this config.





  

    
Re: [PATCH V5 1/7] arm64: dts: sc7280: Add QSPI node

    

      From: Matthias Kaehlcke <mka@chromium.org>

      Date: 2021-09-03 15:46:51 
    

  

  
On Thu, Aug 26, 2021 at 06:29:41PM +0530, rajpat@codeaurora.org wrote:
On 2021-08-12 18:39, Matthias Kaehlcke wrote:
quoted
On Thu, Aug 12, 2021 at 01:11:12PM +0530, Rajesh Patil wrote:
quoted
From: Roja Rani Yarubandi <redacted>

Add QSPI DT node and qspi_opp_table for SC7280 SoC.

Signed-off-by: Roja Rani Yarubandi <redacted>
Signed-off-by: Rajesh Patil <redacted>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 62
++++++++++++++++++++++++++++++++++++
 1 file changed, 62 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi
b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 53a21d0..f8dd5ff 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -415,6 +415,25 @@
 		method = "smc";
 	};

+	qspi_opp_table: qspi-opp-table {
+		compatible = "operating-points-v2";
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-150000000 {
+			opp-hz = /bits/ 64 <150000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+	};
19 more quoted lines
Do you have a link to that discussion so that people can follow along or
chime in?




    
  

  
    

      

        Keyboard shortcuts
      

      

        
          
hback out one level

          
jnext message in thread

          
kprevious message in thread

          
ldrill in

          
Escclose help / fold thread tree

          
?toggle this help