On 09/08/2021 15:10, Christian Hewitt wrote:

Drop this one and directly use vcc_1v8 regulator

+
+	dc_in: regulator-dc_in {
+		compatible = "regulator-fixed";
+		regulator-name = "DC_IN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	}

The name is AO_5V on the Schematics

+
+	vcc_1v8: regulator-vcc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_5V";

The name is "HDMI_PW" on the Schematics

+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_in>;
+
+		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+		enable-active-low;

As the Schematics, the HDMI 5v is always on, no need for a GPIO control here,
please replace with regulator-always-on;

+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_in>;
+		regulator-always-on;
+	};
+
+	vddcpu: regulator-vddcpu {
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <721000>;
+		regulator-max-microvolt = <1022000>;
+
+		vin-supply = <&dc_in>;
+
+		pwms = <&pwm_AO_cd 1 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "RADXA-ZERO";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu2 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu3 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "disabled";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddao_1v8>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	/* WiFi firmware requires power to be kept while in suspend */
+	keep-power-in-suspend;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_1v8>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupts = <&gpio GPIOX_7 GPIO_ACTIVE_HIGH>;
+		interrupt-names = "host-wake";
+	};
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&flash_1v8>;
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
+
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+		max-speed = <2000000>;
+		clocks = <&wifi32k>;
+		clock-names = "lpo";
+	};
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "host";
+};

Type-C controller is missing, something like was done on libretech-pc:

	typec2_vbus: regulator-typec2_vbus {
		typec2_vbus: regulator-typec2_vbus {
		compatible = "regulator-fixed";
		regulator-name = "TYPEC2_VBUS";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		vin-supply = <&vcc5v>;

		gpio = <&gpio_ao GPIOAO_7 GPIO_ACTIVE_HIGH>;
		enable-active-high;
	};


&ao_pinctrl {
	/*
	 * Make sure the irq pin of the TYPE C controller is not driven
	 * by the SoC.
	 */
	fusb302_irq_pins: fusb302_irq {
		mux {
			groups = "GPIOAO_5";
			function = "gpio_aobus";
			bias-pull-up;
			output-disable;
		};
	};
};

&i2c3 {
	status = "okay";
	pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
	pinctrl-names = "default";

	fusb302@22 {
		compatible = "fcs,fusb302";
		reg = <0x22>;

		pinctrl-0 = <&fusb302_irq_pins>;
		pinctrl-names = "default";
		interrupt-parent = <&gpio_intc>;
		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;

		vbus-supply = <&typec2_vbus>;

		status = "okay";
	};
};

&usb2_phy0 {
	phy-supply = <&typec2_vbus>;
};

&usb3_pcie_phy {
	phy-supply = <&typec2_vbus>;
};

But, seems polarity swapping via GPIO is not implemented in drivers/usb/typec/tcpm/fusb302.c so no idea how to handle GPIOAO_6 for USB3 polarity control...
 717 static int tcpm_set_polarity(struct tcpc_dev *dev,
 718                              enum typec_cc_polarity polarity)
 719 {
 720         return 0;
 721 }

Repost with regulator changes, TypeC stuff is not mandatory for v1.

Thanks,
Neil