On Mon, 2021-08-02 at 14:46 -0600, Rob Herring wrote:

On Tue, Jul 27, 2021 at 11:03:15AM -0500, Eddie James wrote:

quoted

Some systems connect several PCA954x devices to a single reset
GPIO. For
these devices to get out of reset and probe successfully, each
device must
defer the probe until the GPIO has been hogged. Accomplish this by
attempting to grab a new "reset-shared-hogged" devicetree property,
but
expect it to fail with EPROBE_DEFER or EBUSY.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 drivers/i2c/muxes/i2c-mux-pca954x.c | 46 +++++++++++++++++++++++
------
 1 file changed, 37 insertions(+), 9 deletions(-)

diff --git a/drivers/i2c/muxes/i2c-mux-pca954x.c

b/drivers/i2c/muxes/i2c-mux-pca954x.c
index 4ad665757dd8..376b54ffb590 100644

--- a/drivers/i2c/muxes/i2c-mux-pca954x.c
+++ b/drivers/i2c/muxes/i2c-mux-pca954x.c

@@ -434,15 +434,43 @@ static int pca954x_probe(struct i2c_client

*client,
 	i2c_set_clientdata(client, muxc);
 	data->client = client;
 
-	/* Reset the mux if a reset GPIO is specified. */
-	gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
-	if (IS_ERR(gpio))
-		return PTR_ERR(gpio);
-	if (gpio) {
-		udelay(1);
-		gpiod_set_value_cansleep(gpio, 0);
-		/* Give the chip some time to recover. */
-		udelay(1);
+	/*
+	 * Grab the shared, hogged gpio that controls the mux reset. We
expect
+	 * this to fail with either EPROBE_DEFER or EBUSY. The only
purpose of
+	 * trying to get it is to make sure the gpio controller has
probed up
+	 * and hogged the line to take the mux out of reset, meaning
that the
+	 * mux is ready to be probed up. Don't try and set the line any
way; in
+	 * the event we actually successfully get the line (if it
wasn't
+	 * hogged) then we immediately release it, since there is no
way to
+	 * sync up the line between muxes.
+	 */
+	gpio = gpiod_get_optional(dev, "reset-shared-hogged", 0);
+	if (IS_ERR(gpio)) {
+		ret = PTR_ERR(gpio);
+		if (ret != -EBUSY)
+			return ret;

Why can't you just do this with the existing 'reset-gpios' property? 
What's the usecase where you'd want to fail probe because EBUSY
other 
than an error in your DT.

Hi, thanks for the reply.

Are you suggesting I use "reset-gpios" and change the driver to ignore
EBUSY? I don't know any other usecase, I just didn't think it would be
acceptable to ignore EBUSY on that, but perhaps it is a better
solution.

Thanks,
Eddie

quoted

+	} else {
+		if (gpio) {
+			/* This is really a problem since now we don't
know the
+			 * state of the gpio. Log a warning and keep
trying to
+			 * probe the mux just in case it works.
+			 */
+			dev_warn(dev, "got hogged reset line, expect
error\n");
+			gpiod_put(gpio);
+		} else {
+			/* Reset the mux if a reset GPIO is specified.
*/
+			gpio = devm_gpiod_get_optional(dev, "reset",
+						       GPIOD_OUT_HIGH);
+			if (IS_ERR(gpio))
+				return PTR_ERR(gpio);
+
+			if (gpio) {
+				udelay(1);
+				gpiod_set_value_cansleep(gpio, 0);
+				/* Give the chip some time to recover.
*/
+				udelay(1);
+			}
+		}
 	}
 
 	data->chip = device_get_match_data(dev);
-- 
2.27.0