Hi Prabhakar,

On Mon, 2021-07-26 at 19:28 +0100, Lad Prabhakar wrote:

Add ADC driver support for Renesas RZ/G2L A/D converter in SW
trigger mode.

A/D Converter block is a successive approximation analog-to-digital
converter with a 12-bit accuracy and supports a maximum of 8 input
channels.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
---
 MAINTAINERS                 |   8 +
 drivers/iio/adc/Kconfig     |  10 +
 drivers/iio/adc/Makefile    |   1 +
 drivers/iio/adc/rzg2l_adc.c | 595 ++++++++++++++++++++++++++++++++++++
 4 files changed, 614 insertions(+)
 create mode 100644 drivers/iio/adc/rzg2l_adc.c

[...]

[...]

+static void rzg2l_adc_pm_runtime_disable(void *data)
+{
+	struct iio_dev *indio_dev = data;
+
+	pm_runtime_disable(indio_dev->dev.parent);
+}
+
+static void rzg2l_adc_reset_assert(void *data)
+{
+	struct reset_control *reset = data;
+
+	reset_control_assert(reset);
+}
+
+static int rzg2l_adc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct iio_dev *indio_dev;
+	struct rzg2l_adc *adc;
+	int ret;
+	int irq;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*adc));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	adc = iio_priv(indio_dev);
+
+	ret = rzg2l_adc_parse_properties(pdev, adc);
+	if (ret)
+		return ret;
+
+	adc->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(adc->base))
+		return PTR_ERR(adc->base);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "no irq resource\n");
+		return irq;
+	}
+
+	adc->pclk = devm_clk_get(dev, "pclk");
+	if (IS_ERR(adc->pclk)) {
+		dev_err(dev, "Failed to get pclk");
+		return PTR_ERR(adc->pclk);
+	}
+
+	adc->adclk = devm_clk_get(dev, "adclk");
+	if (IS_ERR(adc->adclk)) {
+		dev_err(dev, "Failed to get adclk");
+		return PTR_ERR(adc->adclk);
+	}
+
+	adc->adrstn = devm_reset_control_get_exclusive(dev, "adrst-n");
+	if (IS_ERR(adc->adrstn)) {
+		dev_err(dev, "failed to get adrstn\n");
+		return PTR_ERR(adc->adrstn);
+	}

I'd request the "presetn" control up here, so if that fails we don't
touch the "adrst-n" reset line.

+	ret = devm_add_action_or_reset(&pdev->dev,
+				       rzg2l_adc_reset_assert, adc->adrstn);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to register adrstn assert devm action, %d\n",
+			ret);
+		return ret;
+	}

This is the wrong way around. Installing devres actions should be done
after the thing they are supposed to revert in case of error. You should
move this down below the reset_control_deassert(adc->adrstn).

+
+	adc->presetn = devm_reset_control_get_exclusive(dev, "presetn");
+	if (IS_ERR(adc->presetn)) {
+		dev_err(dev, "failed to get presetn\n");
+		return PTR_ERR(adc->presetn);
+	}
+
+	ret = devm_add_action_or_reset(&pdev->dev,
+				       rzg2l_adc_reset_assert, adc->presetn);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to register presetn assert devm action, %d\n",
+			ret);
+		return ret;
+	}

Same as above, this belongs after the presetn deassert below.

+
+	ret = reset_control_deassert(adc->adrstn);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to deassert adrstn pin, %d\n", ret);
+		return ret;
+	}

Here is the place to install the adrstn assert action.

+	ret = reset_control_deassert(adc->presetn);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to deassert presetn pin, %d\n", ret);
+		return ret;
+	}

And here is the place to install the presetn assert action.

regards
Philipp