Hi, Gregory,

The last series was v5. I will rebase on top of Linus 5.13-rcx and then post new v6 set.

Regards
Kosta

-----Original Message-----
From: Gregory CLEMENT <gregory.clement@bootlin.com>
Sent: Thursday, June 17, 2021 18:40
To: Kostya Porotchkin <redacted>; linux-kernel@vger.kernel.org;
devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org
Cc: vladimir.vid@sartura.hr; tmn505@gmail.com; luka.kovacic@sartura.hr;
sebastian.hesselbarth@gmail.com; andrew@lunn.ch; robh+dt@kernel.org;
vkoul@kernel.org; kishon@ti.com; miquel.raynal@bootlin.com;
mw@semihalf.com; jaz@semihalf.com; Nadav Haklai
[off-list ref]; Stefan Chulski [off-list ref]; Ben Peled
[off-list ref]; Kostya Porotchkin [off-list ref]
Subject: [EXT] Re: [PATCH v4 0/5] DTS updates for Marvell Armada CN913x
platforms

External Email

----------------------------------------------------------------------
Hello,

quoted

From: Konstantin Porotchkin <redacted>

This patch series contains the following changes/fixes:
1. Add support for Armada CN913x Development Board topology "B"
2. Add support for Armada CN913x Reference Design boards (CRB) 3.
Fixes the CP11X references in PHY binding document 4. Fixes the NAND
paritioninig scheme in DTS eliminating gap between consecutive
partitions All above changes are already intergated into Marvell
official SDK sources

v2:
- extract common nodes from DB boards to separate DTSI files
- disable eth2 on CRB boards until the required phy mode support is
added
- mention the switch part ID in CRB board description

v3:
- do not rename setup A DTS files for DB variants
- fix a couple of wrong include names

v4:
- Rebase on top of Linus master branch (v5.11-rc7)
- Remove HS400 timing from CRB AP SDHCI (not supported by connected
eMMC)
- Add cd-gpio entry to CP0 SDHCI for SD card support
- Add a comment to CN9130-CRB patch about the required defconfig
  changes for supporting the onboard i2c expander
- Add Stefan's patch to enable 10G port on CN9130-DB platforms

Grzegorz Jaszczyk (1):
  Documentation/bindings: phy: update references to cp11x

Konstantin Porotchkin (3):
  arch/arm64/boot/dts/marvell: fix NAND partitioning scheme
  arm64: dts: cn913x: add device trees for topology B boards
  arm64: dts: add support for Marvell cn9130-crb platform

Stefan Chulski (1):
  dts: marvell: Enable 10G interface on 9130-DB board

I've applied patches 1 and 2, but I have issue with patch 3, there was some
changes around the phys and I am not sure of the correct way to modify the
patch.

Could you rebase it on v5.13-c1 and fix the merge issue ?

Thanks,

Gregory

quoted

 .../bindings/phy/phy-mvebu-comphy.txt         |  12 +-
 arch/arm64/boot/dts/marvell/Makefile          |   5 +
 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts  |  38 ++
arch/arm64/boot/dts/marvell/cn9130-crb-B.dts  |  46 ++
 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi   | 221 ++++++++++
 arch/arm64/boot/dts/marvell/cn9130-db-B.dts   |  22 +
 arch/arm64/boot/dts/marvell/cn9130-db.dts     | 393 +----------------
 arch/arm64/boot/dts/marvell/cn9130-db.dtsi    | 402 ++++++++++++++++++
 arch/arm64/boot/dts/marvell/cn9131-db-B.dts   |  22 +
 arch/arm64/boot/dts/marvell/cn9131-db.dts     | 192 +--------
 arch/arm64/boot/dts/marvell/cn9131-db.dtsi    | 201 +++++++++
 arch/arm64/boot/dts/marvell/cn9132-db-B.dts   |  22 +
 arch/arm64/boot/dts/marvell/cn9132-db.dts     | 211 +--------
 arch/arm64/boot/dts/marvell/cn9132-db.dtsi    | 220 ++++++++++
 14 files changed, 1223 insertions(+), 784 deletions(-)  create mode
100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi

--
2.17.1

--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
https://urldefense.proofpoint.com/v2/url?u=http-
3A__bootlin.com&d=DwIBAg&c=nKjWec2b6R0mOyPaz7xtfQ&r=-
N9sN4p5NSr0JGQoQ_2UCOgAqajG99W1EbSOww0WU8o&m=yb2JOcVicfAZRe
thZJoDE-
wbwtupb3tk_D7VGKCNsqc&s=4oskkLywYJujfGQ4XpFfP6n4ybkC0722K_8qH3xz
bK8&e=