[PATCH v6 0/5] add support for FRAM

@@ -180,6 +180,7 @@ static const char * const nvmem_type_str[] = {
 	[NVMEM_TYPE_EEPROM] = "EEPROM",
 	[NVMEM_TYPE_OTP] = "OTP",
 	[NVMEM_TYPE_BATTERY_BACKED] = "Battery backed",
+	[NVMEM_TYPE_FRAM] = "FRAM",
 };
 
 #ifdef CONFIG_DEBUG_LOCK_ALLOC

@@ -359,6 +360,9 @@ static int nvmem_sysfs_setup_compat(struct nvmem_device *nvmem,
 	if (!config->base_dev)
 		return -EINVAL;
 
+	if (config->type == NVMEM_TYPE_FRAM)
+		bin_attr_nvmem_eeprom_compat.attr.name = "fram";
+
 	nvmem->eeprom = bin_attr_nvmem_eeprom_compat;
 	nvmem->eeprom.attr.mode = nvmem_bin_attr_get_umode(nvmem);
 	nvmem->eeprom.size = nvmem->size;

@@ -25,6 +25,7 @@ enum nvmem_type {
 	NVMEM_TYPE_EEPROM,
 	NVMEM_TYPE_OTP,
 	NVMEM_TYPE_BATTERY_BACKED,
+	NVMEM_TYPE_FRAM,
 };
 
 #define NVMEM_DEVID_NONE	(-1)

@@ -32,12 +32,13 @@ config EEPROM_AT24
 	  will be called at24.
 
 config EEPROM_AT25
-	tristate "SPI EEPROMs from most vendors"
+	tristate "SPI EEPROMs (FRAMs) from most vendors"
 	depends on SPI && SYSFS
 	select NVMEM
 	select NVMEM_SYSFS
 	help
-	  Enable this driver to get read/write support to most SPI EEPROMs,
+	  Enable this driver to get read/write support to most SPI EEPROMs
+	  and Cypress FRAMs,
 	  after you configure the board init code to know about each eeprom
 	  on your target board.
 

@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 /*
  * at25.c -- support most SPI EEPROMs, such as Atmel AT25 models
+ *	     and Cypress FRAMs FM25 models
  *
  * Copyright (C) 2006 David Brownell
  */

@@ -16,6 +17,9 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/eeprom.h>
 #include <linux/property.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/math.h>
 
 /*
  * NOTE: this is an *EEPROM* driver.  The vagaries of product naming

@@ -34,6 +38,7 @@ struct at25_data {
 	unsigned		addrlen;
 	struct nvmem_config	nvmem_config;
 	struct nvmem_device	*nvmem;
+	int has_sernum;
 };
 
 #define	AT25_WREN	0x06		/* latch the write enable */

@@ -42,6 +47,9 @@ struct at25_data {
 #define	AT25_WRSR	0x01		/* write status register */
 #define	AT25_READ	0x03		/* read byte(s) */
 #define	AT25_WRITE	0x02		/* write byte(s)/sector */
+#define	FM25_SLEEP	0xb9		/* enter sleep mode */
+#define	FM25_RDID	0x9f		/* read device ID */
+#define	FM25_RDSN	0xc3		/* read S/N */
 
 #define	AT25_SR_nRDY	0x01		/* nRDY = write-in-progress */
 #define	AT25_SR_WEN	0x02		/* write enable (latched) */

@@ -51,6 +59,9 @@ struct at25_data {
 
 #define	AT25_INSTR_BIT3	0x08		/* Additional address bit in instr */
 
+#define	FM25_ID_LEN	9		/* ID length */
+#define	FM25_SN_LEN	8		/* serial number length */
+
 #define EE_MAXADDRLEN	3		/* 24 bit addresses, up to 2 MBytes */
 
 /* Specs often allow 5 msec for a page write, sometimes 20 msec;

@@ -58,6 +69,9 @@ struct at25_data {
  */
 #define	EE_TIMEOUT	25
 
+#define	IS_EEPROM	0
+#define	IS_FRAM		1
+
 /*-------------------------------------------------------------------------*/
 
 #define	io_limit	PAGE_SIZE	/* bytes */

@@ -129,6 +143,36 @@ static int at25_ee_read(void *priv, unsigned int offset,
 	return status;
 }
 
+/*
+ * read extra registers as ID or serial number
+ */
+static int fm25_aux_read(struct at25_data *at25, char *buf, uint8_t command,
+			 int len)
+{
+	int status;
+	struct spi_transfer t[2];
+	struct spi_message m;
+
+	spi_message_init(&m);
+	memset(t, 0, sizeof(t));
+
+	t[0].tx_buf = &command;
+	t[0].len = 1;
+	spi_message_add_tail(&t[0], &m);
+
+	t[1].rx_buf = buf;
+	t[1].len = len;
+	spi_message_add_tail(&t[1], &m);
+
+	mutex_lock(&at25->lock);
+
+	status = spi_sync(at25->spi, &m);
+	dev_dbg(&at25->spi->dev, "read %d aux bytes --> %d\n", len, status);
+
+	mutex_unlock(&at25->lock);
+	return status;
+}
+
 static int at25_ee_write(void *priv, unsigned int off, void *val, size_t count)
 {
 	struct at25_data *at25 = priv;

@@ -303,34 +347,37 @@ static int at25_fw_to_chip(struct device *dev, struct spi_eeprom *chip)
 	return 0;
 }
 
+static const struct of_device_id at25_of_match[] = {
+	{ .compatible = "atmel,at25", .data = (const void *)IS_EEPROM },
+	{ .compatible = "cypress,fm25", .data = (const void *)IS_FRAM },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, at25_of_match);
+
 static int at25_probe(struct spi_device *spi)
 {
 	struct at25_data	*at25 = NULL;
 	struct spi_eeprom	chip;
 	int			err;
 	int			sr;
-	int			addrlen;
+	char id[FM25_ID_LEN];
+	const struct of_device_id *match;
+	int is_fram = 0;
+
+	match = of_match_device(of_match_ptr(at25_of_match), &spi->dev);
+	if (match)
+		is_fram = (int)(uintptr_t)match->data;
 
 	/* Chip description */
 	if (!spi->dev.platform_data) {
-		err = at25_fw_to_chip(&spi->dev, &chip);
-		if (err)
-			return err;
+		if (!is_fram) {
+			err = at25_fw_to_chip(&spi->dev, &chip);
+			if (err)
+				return err;
+		}
 	} else
 		chip = *(struct spi_eeprom *)spi->dev.platform_data;
 
-	/* For now we only support 8/16/24 bit addressing */
-	if (chip.flags & EE_ADDR1)
-		addrlen = 1;
-	else if (chip.flags & EE_ADDR2)
-		addrlen = 2;
-	else if (chip.flags & EE_ADDR3)
-		addrlen = 3;
-	else {
-		dev_dbg(&spi->dev, "unsupported address type\n");
-		return -EINVAL;
-	}
-
 	/* Ping the chip ... the status register is pretty portable,
 	 * unlike probing manufacturer IDs.  We do expect that system
 	 * firmware didn't write it in the past few milliseconds!

@@ -349,9 +396,49 @@ static int at25_probe(struct spi_device *spi)
 	at25->chip = chip;
 	at25->spi = spi;
 	spi_set_drvdata(spi, at25);
-	at25->addrlen = addrlen;
 
-	at25->nvmem_config.type = NVMEM_TYPE_EEPROM;
+	if (is_fram) {
+		/* Get ID of chip */
+		fm25_aux_read(at25, id, FM25_RDID, FM25_ID_LEN);
+		if (id[6] != 0xc2) {
+			dev_err(&spi->dev,
+				"Error: no Cypress FRAM (id %02x)\n", id[6]);
+			return -ENODEV;
+		}
+		/* set size found in ID */
+		if (id[7] < 0x21 || id[7] > 0x26) {
+			dev_err(&spi->dev, "Error: unsupported size (id %02x)\n", id[7]);
+			return -ENODEV;
+		}
+		chip.byte_len = int_pow(2, id[7] - 0x21 + 4) * 1024;
+
+		if (at25->chip.byte_len > 64 * 1024)
+			at25->chip.flags |= EE_ADDR3;
+		else
+			at25->chip.flags |= EE_ADDR2;
+
+		if (id[8])
+			at25->has_sernum = 1;
+		else
+			at25->has_sernum = 0;
+
+		at25->chip.page_size = PAGE_SIZE;
+		strncpy(at25->chip.name, "fm25", sizeof(at25->chip.name));
+	}
+
+	/* For now we only support 8/16/24 bit addressing */
+	if (at25->chip.flags & EE_ADDR1)
+		at25->addrlen = 1;
+	else if (at25->chip.flags & EE_ADDR2)
+		at25->addrlen = 2;
+	else if (at25->chip.flags & EE_ADDR3)
+		at25->addrlen = 3;
+	else {
+		dev_dbg(&spi->dev, "unsupported address type\n");
+		return -EINVAL;
+	}
+
+	at25->nvmem_config.type = is_fram ? NVMEM_TYPE_FRAM : NVMEM_TYPE_EEPROM;
 	at25->nvmem_config.name = dev_name(&spi->dev);
 	at25->nvmem_config.dev = &spi->dev;
 	at25->nvmem_config.read_only = chip.flags & EE_READONLY;

@@ -370,23 +457,17 @@ static int at25_probe(struct spi_device *spi)
 	if (IS_ERR(at25->nvmem))
 		return PTR_ERR(at25->nvmem);
 
-	dev_info(&spi->dev, "%d %s %s eeprom%s, pagesize %u\n",
-		(chip.byte_len < 1024) ? chip.byte_len : (chip.byte_len / 1024),
-		(chip.byte_len < 1024) ? "Byte" : "KByte",
-		at25->chip.name,
-		(chip.flags & EE_READONLY) ? " (readonly)" : "",
-		at25->chip.page_size);
+	dev_info(&spi->dev, "%d %s %s %s%s, pagesize %u\n",
+		 (chip.byte_len < 1024) ? chip.byte_len : (chip.byte_len / 1024),
+		 (chip.byte_len < 1024) ? "Byte" : "KByte",
+		 at25->chip.name, is_fram ? "fram" : "eeprom",
+		 (chip.flags & EE_READONLY) ? " (readonly)" : "",
+		 at25->chip.page_size);
 	return 0;
 }
 
 /*-------------------------------------------------------------------------*/
 
-static const struct of_device_id at25_of_match[] = {
-	{ .compatible = "atmel,at25", },
-	{ }
-};
-MODULE_DEVICE_TABLE(of, at25_of_match);
-
 static struct spi_driver at25_driver = {
 	.driver = {
 		.name		= "at25",

@@ -4,14 +4,16 @@
 $id: "http://devicetree.org/schemas/eeprom/at25.yaml#"
 $schema: "http://devicetree.org/meta-schemas/core.yaml#"
 
-title: SPI EEPROMs compatible with Atmel's AT25
+title: SPI EEPROMs or FRAMs compatible with Atmel's AT25
 
 maintainers:
   - Christian Eggers <ceggers@arri.de>
 
 properties:
   $nodename:
-    pattern: "^eeprom@[0-9a-f]{1,2}$"
+    anyOf:
+      - pattern: "^eeprom@[0-9a-f]{1,2}$"
+      - pattern: "^fram@[0-9a-f]{1,2}$"
 
   # There are multiple known vendors who manufacture EEPROM chips compatible
   # with Atmel's AT25. The compatible string requires two items where the

@@ -31,6 +33,7 @@ properties:
               - microchip,25lc040
               - st,m95m02
               - st,m95256
+              - cypress,fm25
 
           - const: atmel,at25
 

@@ -48,7 +51,7 @@ properties:
     $ref: /schemas/types.yaml#/definitions/uint32
     enum: [1, 8, 16, 32, 64, 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768, 65536, 131072]
     description:
-      Size of the eeprom page.
+      Size of the eeprom page. FRAMs don't have pages.
 
   size:
     $ref: /schemas/types.yaml#/definitions/uint32

@@ -101,9 +104,19 @@ required:
   - compatible
   - reg
   - spi-max-frequency
-  - pagesize
-  - size
-  - address-width
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          not:
+            contains:
+              const: cypress,fm25
+    then:
+      required:
+        - pagesize
+        - size
+        - address-width
 
 additionalProperties: false
 

@@ -126,4 +139,10 @@ examples:
             size = <32768>;
             address-width = <16>;
         };
+
+        fram@1 {
+            compatible = "cypress,fm25", "atmel,at25";
+            reg = <1>;
+            spi-max-frequency = <40000000>;
+        };
     };

@@ -39,6 +39,7 @@ struct at25_data {
 	struct nvmem_config	nvmem_config;
 	struct nvmem_device	*nvmem;
 	int has_sernum;
+	char *sernum;
 };
 
 #define	AT25_WREN	0x06		/* latch the write enable */

@@ -173,6 +174,25 @@ static int fm25_aux_read(struct at25_data *at25, char *buf, uint8_t command,
 	return status;
 }
 
+static ssize_t sernum_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct at25_data *at25;
+	int i;
+
+	at25 = dev_get_drvdata(dev);
+	for (i = FM25_SN_LEN - 1; i >= 0; i--)
+		buf += sprintf(buf, "%02x", at25->sernum[i]);
+	sprintf(buf, "\n");
+	return (2 * FM25_SN_LEN + 1);
+}
+static DEVICE_ATTR(sernum, 0440, sernum_show, NULL);
+
+static struct attribute *sernum_attrs[] = {
+	&dev_attr_sernum.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(sernum);
+
 static int at25_ee_write(void *priv, unsigned int off, void *val, size_t count)
 {
 	struct at25_data *at25 = priv;

@@ -417,8 +437,13 @@ static int at25_probe(struct spi_device *spi)
 		else
 			at25->chip.flags |= EE_ADDR2;
 
-		if (id[8])
+		if (id[8]) {
 			at25->has_sernum = 1;
+			at25->sernum = kzalloc(FM25_SN_LEN, GFP_KERNEL);
+			if (!at25->sernum)
+				return -ENOMEM;
+			fm25_aux_read(at25, at25->sernum, FM25_RDSN, FM25_SN_LEN);
+		}
 		else
 			at25->has_sernum = 0;
 

@@ -472,6 +497,7 @@ static struct spi_driver at25_driver = {
 	.driver = {
 		.name		= "at25",
 		.of_match_table = at25_of_match,
+		.dev_groups	= sernum_groups,
 	},
 	.probe		= at25_probe,
 };

@@ -0,0 +1,6 @@
+What:		/sys/class/spi_master/spi<bus>/spi<bus>.<dev>/sernum
+Date:		May 2021
+KernelVersion:	5.12.1
+Contact:	Jiri Prchal <jiri.prchal@aksignal.cz>
+Description:
+		Exports serial number of Cypress FRAM (FM25VN). 8 bytes as is in chip in hex string.