[PATCH v4 1/2] dt-bindings: usb: dwc3-xilinx: Add documentation for Versal DWC3 Controller
From: Manish Narani <hidden>
Date: 2021-03-17 06:54:21
Also in:
linux-arm-kernel, linux-usb, lkml
Subsystem:
open firmware and flattened device tree bindings, the rest, usb subsystem · Maintainers:
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds, Greg Kroah-Hartman
Add documentation for Versal DWC3 controller. Add required property 'reg' for the same. Also add optional properties for snps,dwc3. Signed-off-by: Manish Narani <redacted> Reviewed-by: Rob Herring <robh@kernel.org> --- .../devicetree/bindings/usb/dwc3-xilinx.txt | 28 ++++++++++++++++++++-- 1 file changed, 26 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt b/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt
index a668f43..04813a4 100644
--- a/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt
+++ b/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt@@ -1,32 +1,56 @@ Xilinx SuperSpeed DWC3 USB SoC controller Required properties: -- compatible: Should contain "xlnx,zynqmp-dwc3" +- compatible: May contain "xlnx,zynqmp-dwc3" or "xlnx,versal-dwc3" +- reg: Base address and length of the register control block - clocks: A list of phandles for the clocks listed in clock-names - clock-names: Should contain the following: "bus_clk" Master/Core clock, have to be >= 125 MHz for SS operation and >= 60MHz for HS operation "ref_clk" Clock source to core during PHY power down +- resets: A list of phandles for resets listed in reset-names +- reset-names: + "usb_crst" USB core reset + "usb_hibrst" USB hibernation reset + "usb_apbrst" USB APB reset Required child node: A child node must exist to represent the core DWC3 IP block. The name of the node is not important. The content of the node is defined in dwc3.txt. +Optional properties for snps,dwc3: +- dma-coherent: Enable this flag if CCI is enabled in design. Adding this + flag configures Global SoC bus Configuration Register and + Xilinx USB 3.0 IP - USB coherency register to enable CCI. +- interrupt-names: Should contain the following: + "dwc_usb3" USB gadget mode interrupts + "otg" USB OTG mode interrupts + "hiber" USB hibernation interrupts + Example device node: usb@0 { #address-cells = <0x2>; #size-cells = <0x1>; compatible = "xlnx,zynqmp-dwc3"; + reg = <0x0 0xff9d0000 0x0 0x100>; clock-names = "bus_clk", "ref_clk"; clocks = <&clk125>, <&clk125>; + resets = <&zynqmp_reset ZYNQMP_RESET_USB1_CORERESET>, + <&zynqmp_reset ZYNQMP_RESET_USB1_HIBERRESET>, + <&zynqmp_reset ZYNQMP_RESET_USB1_APB>; + reset-names = "usb_crst", "usb_hibrst", "usb_apbrst"; ranges; dwc3@fe200000 { compatible = "snps,dwc3"; reg = <0x0 0xfe200000 0x40000>; - interrupts = <0x0 0x41 0x4>; + interrupt-names = "dwc_usb3", "otg", "hiber"; + interrupts = <0 65 4>, <0 69 4>, <0 75 4>; + phys = <&psgtr 2 PHY_TYPE_USB3 0 2>; + phy-names = "usb3-phy"; dr_mode = "host"; + dma-coherent; }; };
--
2.1.1