Convert the Renesas DRIF bindings to DT schema and update
MAINTAINERS accordingly.

Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
v3->v4:
* Replace "if" statement with "else" statement for the branch
  rejecting pinctrl-0 and pinctrl-names properties, as suggested
  by Geert
v2->v3:
* Removed the definition of pinctrl-0 and pinctrl-names, as
  suggested by Geert
* Added "power-domains" to the list of required properties,
  as suggested by Geert
v1->v2:
* s/controller/Controller/ in the title of renesas,drif.yaml
  as suggested by Laurent.

 .../bindings/media/renesas,drif.txt           | 177 -----------
 .../bindings/media/renesas,drif.yaml          | 277 ++++++++++++++++++
 MAINTAINERS                                   |   2 +-
 3 files changed, 278 insertions(+), 178 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/media/renesas,drif.txt
 create mode 100644 Documentation/devicetree/bindings/media/renesas,drif.yaml

diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt b/Documentation/devicetree/bindings/media/renesas,drif.txt
deleted file mode 100644
index 0d8974aa8b38..000000000000
--- a/Documentation/devicetree/bindings/media/renesas,drif.txt
+++ /dev/null

@@ -1,177 +0,0 @@
-Renesas R-Car Gen3 Digital Radio Interface controller (DRIF)
-------------------------------------------------------------
-
-R-Car Gen3 DRIF is a SPI like receive only slave device. A general
-representation of DRIF interfacing with a master device is shown below.
-
-+---------------------+                +---------------------+
-|                     |-----SCK------->|CLK                  |
-|       Master        |-----SS-------->|SYNC  DRIFn (slave)  |
-|                     |-----SD0------->|D0                   |
-|                     |-----SD1------->|D1                   |
-+---------------------+                +---------------------+
-
-As per datasheet, each DRIF channel (drifn) is made up of two internal
-channels (drifn0 & drifn1). These two internal channels share the common
-CLK & SYNC. Each internal channel has its own dedicated resources like
-irq, dma channels, address space & clock. This internal split is not
-visible to the external master device.
-
-The device tree model represents each internal channel as a separate node.
-The internal channels sharing the CLK & SYNC are tied together by their
-phandles using a property called "renesas,bonding". For the rest of
-the documentation, unless explicitly stated, the word channel implies an
-internal channel.
-
-When both internal channels are enabled they need to be managed together
-as one (i.e.) they cannot operate alone as independent devices. Out of the
-two, one of them needs to act as a primary device that accepts common
-properties of both the internal channels. This channel is identified by a
-property called "renesas,primary-bond".
-
-To summarize,
-   - When both the internal channels that are bonded together are enabled,
-     the zeroth channel is selected as primary-bond. This channels accepts
-     properties common to all the members of the bond.
-   - When only one of the bonded channels need to be enabled, the property
-     "renesas,bonding" or "renesas,primary-bond" will have no effect. That
-     enabled channel can act alone as any other independent device.
-
-Required properties of an internal channel:
--------------------------------------------
-- compatible:	"renesas,r8a7795-drif" if DRIF controller is a part of R8A7795 SoC.
-		"renesas,r8a7796-drif" if DRIF controller is a part of R8A7796 SoC.
-		"renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible device.
-
-		When compatible with the generic version, nodes must list the
-		SoC-specific version corresponding to the platform first
-		followed by the generic version.
-
-- reg: offset and length of that channel.
-- interrupts: associated with that channel.
-- clocks: phandle and clock specifier of that channel.
-- clock-names: clock input name string: "fck".
-- dmas: phandles to the DMA channels.
-- dma-names: names of the DMA channel: "rx".
-- renesas,bonding: phandle to the other channel.
-
-Optional properties of an internal channel:
--------------------------------------------
-- power-domains: phandle to the respective power domain.
-
-Required properties of an internal channel when:
-	- It is the only enabled channel of the bond (or)
-	- If it acts as primary among enabled bonds
---------------------------------------------------------
-- pinctrl-0: pin control group to be used for this channel.
-- pinctrl-names: must be "default".
-- renesas,primary-bond: empty property indicating the channel acts as primary
-			among the bonded channels.
-- port: child port node corresponding to the data input, in accordance with
-	the video interface bindings defined in
-	Documentation/devicetree/bindings/media/video-interfaces.txt. The port
-	node must contain at least one endpoint.
-
-Optional endpoint property:
----------------------------
-- sync-active: Indicates sync signal polarity, 0/1 for low/high respectively.
-	       This property maps to SYNCAC bit in the hardware manual. The
-	       default is 1 (active high).
-
-Example:
---------
-
-(1) Both internal channels enabled:
------------------------------------
-
-When interfacing with a third party tuner device with two data pins as shown
-below.
-
-+---------------------+                +---------------------+
-|                     |-----SCK------->|CLK                  |
-|       Master        |-----SS-------->|SYNC  DRIFn (slave)  |
-|                     |-----SD0------->|D0                   |
-|                     |-----SD1------->|D1                   |
-+---------------------+                +---------------------+
-
-	drif00: rif@e6f40000 {
-		compatible = "renesas,r8a7795-drif",
-			     "renesas,rcar-gen3-drif";
-		reg = <0 0xe6f40000 0 0x64>;
-		interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cpg CPG_MOD 515>;
-		clock-names = "fck";
-		dmas = <&dmac1 0x20>, <&dmac2 0x20>;
-		dma-names = "rx", "rx";
-		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
-		renesas,bonding = <&drif01>;
-		renesas,primary-bond;
-		pinctrl-0 = <&drif0_pins>;
-		pinctrl-names = "default";
-		port {
-			drif0_ep: endpoint {
-			     remote-endpoint = <&tuner_ep>;
-			};
-		};
-	};
-
-	drif01: rif@e6f50000 {
-		compatible = "renesas,r8a7795-drif",
-			     "renesas,rcar-gen3-drif";
-		reg = <0 0xe6f50000 0 0x64>;
-		interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cpg CPG_MOD 514>;
-		clock-names = "fck";
-		dmas = <&dmac1 0x22>, <&dmac2 0x22>;
-		dma-names = "rx", "rx";
-		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
-		renesas,bonding = <&drif00>;
-	};
-
-
-(2) Internal channel 1 alone is enabled:
-----------------------------------------
-
-When interfacing with a third party tuner device with one data pin as shown
-below.
-
-+---------------------+                +---------------------+
-|                     |-----SCK------->|CLK                  |
-|       Master        |-----SS-------->|SYNC  DRIFn (slave)  |
-|                     |                |D0 (unused)          |
-|                     |-----SD-------->|D1                   |
-+---------------------+                +---------------------+
-
-	drif00: rif@e6f40000 {
-		compatible = "renesas,r8a7795-drif",
-			     "renesas,rcar-gen3-drif";
-		reg = <0 0xe6f40000 0 0x64>;
-		interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cpg CPG_MOD 515>;
-		clock-names = "fck";
-		dmas = <&dmac1 0x20>, <&dmac2 0x20>;
-		dma-names = "rx", "rx";
-		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
-		renesas,bonding = <&drif01>;
-	};
-
-	drif01: rif@e6f50000 {
-		compatible = "renesas,r8a7795-drif",
-			     "renesas,rcar-gen3-drif";
-		reg = <0 0xe6f50000 0 0x64>;
-		interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cpg CPG_MOD 514>;
-		clock-names = "fck";
-		dmas = <&dmac1 0x22>, <&dmac2 0x22>;
-		dma-names = "rx", "rx";
-		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
-		renesas,bonding = <&drif00>;
-		pinctrl-0 = <&drif0_pins>;
-		pinctrl-names = "default";
-		port {
-			drif0_ep: endpoint {
-			     remote-endpoint = <&tuner_ep>;
-			     sync-active = <0>;
-			};
-		};
-	};

diff --git a/Documentation/devicetree/bindings/media/renesas,drif.yaml b/Documentation/devicetree/bindings/media/renesas,drif.yaml
new file mode 100644
index 000000000000..3832ce837553
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/renesas,drif.yaml

@@ -0,0 +1,277 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/renesas,drif.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas R-Car Gen3 Digital Radio Interface Controller (DRIF)
+
+maintainers:
+  - Ramesh Shanmugasundaram <rashanmu@gmail.com>
+  - Fabrizio Castro <fabrizio.castro.jz@renesas.com>
+
+description: |
+  R-Car Gen3 DRIF is a SPI like receive only slave device. A general
+  representation of DRIF interfacing with a master device is shown below.
+
+  +---------------------+                +---------------------+
+  |                     |-----SCK------->|CLK                  |
+  |       Master        |-----SS-------->|SYNC  DRIFn (slave)  |
+  |                     |-----SD0------->|D0                   |
+  |                     |-----SD1------->|D1                   |
+  +---------------------+                +---------------------+
+
+  As per datasheet, each DRIF channel (drifn) is made up of two internal
+  channels (drifn0 & drifn1). These two internal channels share the common
+  CLK & SYNC. Each internal channel has its own dedicated resources like
+  irq, dma channels, address space & clock. This internal split is not
+  visible to the external master device.
+
+  The device tree model represents each internal channel as a separate node.
+  The internal channels sharing the CLK & SYNC are tied together by their
+  phandles using a property called "renesas,bonding". For the rest of
+  the documentation, unless explicitly stated, the word channel implies an
+  internal channel.
+
+  When both internal channels are enabled they need to be managed together
+  as one (i.e.) they cannot operate alone as independent devices. Out of the
+  two, one of them needs to act as a primary device that accepts common
+  properties of both the internal channels. This channel is identified by a
+  property called "renesas,primary-bond".
+
+  To summarize,
+     * When both the internal channels that are bonded together are enabled,
+       the zeroth channel is selected as primary-bond. This channels accepts
+       properties common to all the members of the bond.
+     * When only one of the bonded channels need to be enabled, the property
+       "renesas,bonding" or "renesas,primary-bond" will have no effect. That
+       enabled channel can act alone as any other independent device.
+
+properties:
+  compatible:
+    items:
+      - enum:
+        - renesas,r8a7795-drif        # R-Car H3
+        - renesas,r8a7796-drif        # R-Car M3-W