[PATCH 2/3] Arm: dts: aspeed-g6: Add sgpio node
From: Billy Tsai <hidden>
Date: 2020-10-12 03:33:18
Also in:
linux-arm-kernel, linux-aspeed, linux-gpio, lkml, openbmc
Subsystem:
gpio subsystem, open firmware and flattened device tree bindings, the rest · Maintainers:
Linus Walleij, Bartosz Golaszewski, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds
This patch is used to add sgpiom and sgpios nodes and add compatiable string for sgpiom. Signed-off-by: Billy Tsai <redacted> --- .../devicetree/bindings/gpio/sgpio-aspeed.txt | 8 +-- arch/arm/boot/dts/aspeed-g6.dtsi | 52 +++++++++++++++++++ 2 files changed, 57 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt b/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt
index d4d83916c09d..815d9b5167a5 100644
--- a/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt
+++ b/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt@@ -1,8 +1,10 @@ Aspeed SGPIO controller Device Tree Bindings -------------------------------------------- -This SGPIO controller is for ASPEED AST2500 SoC, it supports up to 80 full -featured Serial GPIOs. Each of the Serial GPIO pins can be programmed to +This SGPIO controller is for ASPEED AST2500/AST2600 SoC, it supports 2 master. +One is up to 128 SGPIO input ports and 128 output ports concurrently(after AST2600A1) +and Second one is up to 80. +Each of the Serial GPIO pins can be programmed to support the following options: - Support interrupt option for each input port and various interrupt sensitivity option (level-high, level-low, edge-high, edge-low)
@@ -14,7 +16,7 @@ support the following options: Required properties: - compatible : Should be one of - "aspeed,ast2400-sgpio", "aspeed,ast2500-sgpio" + "aspeed,ast2400-sgpio", "aspeed,ast2500-sgpio", "aspeed,ast2600-sgpiom" - #gpio-cells : Should be 2, see gpio.txt - reg : Address and length of the register set for the device - gpio-controller : Marks the device node as a GPIO controller
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi
index ad19dce038ea..cb053a996e87 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6.dtsi@@ -366,6 +366,58 @@ #interrupt-cells = <2>; }; + sgpiom0: sgpiom@1e780500 { + #gpio-cells = <2>; + gpio-controller; + compatible = "aspeed,ast2600-sgpiom"; + reg = <0x1e780500 0x100>; + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; + ngpios = <128>; + clocks = <&syscon ASPEED_CLK_APB2>; + interrupt-controller; + bus-frequency = <12000000>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sgpm1_default>; + status = "disabled"; + }; + + sgpiom1: sgpiom@1e780600 { + #gpio-cells = <2>; + gpio-controller; + compatible = "aspeed,ast2600-sgpiom"; + reg = <0x1e780600 0x100>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + ngpios = <80>; + clocks = <&syscon ASPEED_CLK_APB2>; + interrupt-controller; + bus-frequency = <12000000>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sgpm2_default>; + status = "disabled"; + }; + + sgpios0: sgpios@1e780700 { + #gpio-cells = <2>; + gpio-controller; + compatible = "aspeed,ast2600-sgpios"; + reg = <0x1e780700 0x40>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&syscon ASPEED_CLK_APB2>; + status = "disabled"; + }; + + sgpios1: sgpios@1e780740 { + #gpio-cells = <2>; + gpio-controller; + compatible = "aspeed,ast2600-sgpios"; + reg = <0x1e780740 0x40>; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&syscon ASPEED_CLK_APB2>; + status = "disabled"; + }; + gpio1: gpio@1e780800 { #gpio-cells = <2>; gpio-controller;
--
2.17.1