[PATCH 15/20] dt-bindings:iio:adc:ad7768-1 yaml conversion
From: Jonathan Cameron <jic23@kernel.org>
Date: 2020-09-05 17:32:55
Also in:
linux-iio
Subsystem:
analog devices inc ad7768-1 driver, analog devices inc iio drivers, iio subsystem and drivers, open firmware and flattened device tree bindings, the rest · Maintainers:
Michael Hennerich, Lars-Peter Clausen, Jonathan Cameron, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds
From: Jonathan Cameron <Jonathan.Cameron@huawei.com> Fairly straight conversion. The one oddity in the original binding is that spi-cpha and spi-cpol were not marked as required, but were in the example. Looking at the datasheet, there isn't any documented flexibility in the possible SPI modes, so I have moved these to requires. For spi-max-frequency I have gone the other way. I absolutely agree that it is good to specify this in the dt-binding, but it's not strictly required. Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Stefan Popa <redacted> --- .../bindings/iio/adc/adi,ad7768-1.txt | 41 --------- .../bindings/iio/adc/adi,ad7768-1.yaml | 89 +++++++++++++++++++ 2 files changed, 89 insertions(+), 41 deletions(-)
diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt
deleted file mode 100644
index 9f5b88cf680d..000000000000
--- a/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt
+++ /dev/null@@ -1,41 +0,0 @@ -Analog Devices AD7768-1 ADC device driver - -Required properties for the AD7768-1: - -- compatible: Must be "adi,ad7768-1" -- reg: SPI chip select number for the device -- spi-max-frequency: Max SPI frequency to use - see: Documentation/devicetree/bindings/spi/spi-bus.txt -- clocks: phandle to the master clock (mclk) - see: Documentation/devicetree/bindings/clock/clock-bindings.txt -- clock-names: Must be "mclk". -- interrupts: IRQ line for the ADC - see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt -- vref-supply: vref supply can be used as reference for conversion -- adi,sync-in-gpios: must be the device tree identifier of the SYNC-IN pin. Enables - synchronization of multiple devices that require simultaneous sampling. - A pulse is always required if the configuration is changed in any way, for example - if the filter decimation rate changes. As the line is active low, it should - be marked GPIO_ACTIVE_LOW. - -Optional properties: - - - reset-gpios : GPIO spec for the RESET pin. If specified, it will be asserted during - driver probe. As the line is active low, it should be marked GPIO_ACTIVE_LOW. - -Example: - - adc@0 { - compatible = "adi,ad7768-1"; - reg = <0>; - spi-max-frequency = <2000000>; - spi-cpol; - spi-cpha; - vref-supply = <&adc_vref>; - interrupts = <25 IRQ_TYPE_EDGE_RISING>; - interrupt-parent = <&gpio>; - adi,sync-in-gpios = <&gpio 22 GPIO_ACTIVE_LOW>; - reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>; - clocks = <&ad7768_mclk>; - clock-names = "mclk"; - };
diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.yaml
new file mode 100644
index 000000000000..a2c559d0c947
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.yaml@@ -0,0 +1,89 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/adi,ad7768-1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD7768-1 ADC device driver + +maintainers: + - Stefan Popa <stefan.popa@analog.com> + +description: | + Datasheet at: + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7768-1.pdf + +properties: + compatible: + const: adi,ad7768-1 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: mclk + + interrupts: + maxItems: 1 + + vref-supply: + description: + ADC reference voltage supply + + adi,sync-in-gpios: + description: + Enables synchronization of multiple devices that require simultaneous + sampling. A pulse is always required if the configuration is changed + in any way, for example if the filter decimation rate changes. + As the line is active low, it should be marked GPIO_ACTIVE_LOW. + + reset-gpios: + maxItems: 1 + + spi-max-frequency: true + + spi-cpol: true + spi-cpha : true + + "#io-channel-cells": + const: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - vref-supply + - spi-cpol + - spi-cpha + - adi,sync-in-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "adi,ad7768-1"; + reg = <0>; + spi-max-frequency = <2000000>; + spi-cpol; + spi-cpha; + vref-supply = <&adc_vref>; + interrupts = <25 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&gpio>; + adi,sync-in-gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>; + clocks = <&ad7768_mclk>; + clock-names = "mclk"; + }; + }; +...
--
2.28.0