On 22/03/18 10:10, Chunfeng Yun wrote:

Hi,
On Wed, 2018-03-21 at 13:30 +0200, Roger Quadros wrote:

quoted

Martin,

On 21/03/18 00:01, Martin Blumenstingl wrote:

quoted

Hi Roger, Hi Chunfeng,

On Tue, Mar 20, 2018 at 1:04 PM, Chunfeng Yun [off-list ref] wrote:

quoted

Hi Martin & Roger:

On Mon, 2018-03-19 at 17:12 +0100, Martin Blumenstingl wrote:

quoted

Hi Roger,

On Mon, Mar 19, 2018 at 9:49 AM, Roger Quadros [off-list ref] wrote:

quoted

Hi,

On 19/03/18 00:29, Martin Blumenstingl wrote:

quoted

Hi Roger,

On Fri, Mar 16, 2018 at 3:32 PM, Roger Quadros [off-list ref] wrote:

quoted

+some TI folks

Hi Martin,

On 18/02/18 20:44, Martin Blumenstingl wrote:

quoted

Many SoC platforms have separate devices for the USB PHY which are
registered through the generic PHY framework. These PHYs have to be
enabled to make the USB controller actually work. They also have to be
disabled again on shutdown/suspend.

Currently (at least) the following HCI platform drivers are using custom
code to obtain all PHYs via devicetree for the roothub/controller and
disable/enable them when required:
- ehci-platform.c has ehci_platform_power_{on,off}
- xhci-mtk.c has xhci_mtk_phy_{init,exit,power_on,power_off}
- ohci-platform.c has ohci_platform_power_{on,off}

With this new wrapper the USB PHYs can be specified directly in the
USB controller's devicetree node (just like on the drivers listed
above). This allows SoCs like the Amlogic Meson GXL family to operate
correctly once this is wired up correctly. These SoCs use a dwc3
controller and require all USB PHYs to be initialized (if one of the USB
PHYs it not initialized then none of USB port works at all).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
Tested-by: Yixun Lan <redacted>
Cc: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Cc: Chunfeng Yun <chunfeng.yun-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>

This patch is breaking low power cases on TI SoCs when USB is in host mode.
I'll explain why below.

based on your explanation and reading the TI PHY drivers I am assuming
that the affected SoCs are using the "phy-omap-usb2" driver

yes and phy-ti-pipe3 as well i.e. "ti,phy-usb3" and "ti,omap-usb3"

I missed that, thanks

quoted

quoted

quoted

quoted

---
 drivers/usb/core/Makefile |   2 +-
 drivers/usb/core/phy.c    | 158 ++++++++++++++++++++++++++++++++++++++++++++++
 drivers/usb/core/phy.h    |   7 ++
 3 files changed, 166 insertions(+), 1 deletion(-)
 create mode 100644 drivers/usb/core/phy.c
 create mode 100644 drivers/usb/core/phy.h

diff --git a/drivers/usb/core/Makefile b/drivers/usb/core/Makefile
index 92c9cefb4317..18e874b0441e 100644
--- a/drivers/usb/core/Makefile
+++ b/drivers/usb/core/Makefile

@@ -6,7 +6,7 @@
 usbcore-y := usb.o hub.o hcd.o urb.o message.o driver.o
 usbcore-y += config.o file.o buffer.o sysfs.o endpoint.o
 usbcore-y += devio.o notify.o generic.o quirks.o devices.o
-usbcore-y += port.o
+usbcore-y += phy.o port.o

 usbcore-$(CONFIG_OF)         += of.o
 usbcore-$(CONFIG_USB_PCI)            += hcd-pci.o

diff --git a/drivers/usb/core/phy.c b/drivers/usb/core/phy.c
new file mode 100644
index 000000000000..09b7c43c0ea4
--- /dev/null
+++ b/drivers/usb/core/phy.c

@@ -0,0 +1,158 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * A wrapper for multiple PHYs which passes all phy_* function calls to
+ * multiple (actual) PHY devices. This is comes handy when initializing
+ * all PHYs on a HCD and to keep them all in the same state.
+ *
+ * Copyright (C) 2018 Martin Blumenstingl <martin.blumenstingl-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
+ */
+
+#include <linux/device.h>
+#include <linux/list.h>
+#include <linux/phy/phy.h>
+#include <linux/of.h>
+
+#include "phy.h"
+
+struct usb_phy_roothub {
+     struct phy              *phy;
+     struct list_head        list;
+};
+
+static struct usb_phy_roothub *usb_phy_roothub_alloc(struct device *dev)
+{
+     struct usb_phy_roothub *roothub_entry;
+
+     roothub_entry = devm_kzalloc(dev, sizeof(*roothub_entry), GFP_KERNEL);
+     if (!roothub_entry)
+             return ERR_PTR(-ENOMEM);
+
+     INIT_LIST_HEAD(&roothub_entry->list);
+
+     return roothub_entry;
+}
+
+static int usb_phy_roothub_add_phy(struct device *dev, int index,
+                                struct list_head *list)
+{
+     struct usb_phy_roothub *roothub_entry;
+     struct phy *phy = devm_of_phy_get_by_index(dev, dev->of_node, index);
+
+     if (IS_ERR_OR_NULL(phy)) {
+             if (!phy || PTR_ERR(phy) == -ENODEV)
+                     return 0;
+             else
+                     return PTR_ERR(phy);
+     }
+
+     roothub_entry = usb_phy_roothub_alloc(dev);
+     if (IS_ERR(roothub_entry))
+             return PTR_ERR(roothub_entry);
+
+     roothub_entry->phy = phy;
+
+     list_add_tail(&roothub_entry->list, list);
+
+     return 0;
+}
+
+struct usb_phy_roothub *usb_phy_roothub_init(struct device *dev)
+{
+     struct usb_phy_roothub *phy_roothub;
+     struct usb_phy_roothub *roothub_entry;
+     struct list_head *head;
+     int i, num_phys, err;
+
+     num_phys = of_count_phandle_with_args(dev->of_node, "phys",
+                                           "#phy-cells");
+     if (num_phys <= 0)
+             return NULL;
+
+     phy_roothub = usb_phy_roothub_alloc(dev);
+     if (IS_ERR(phy_roothub))
+             return phy_roothub;
+
+     for (i = 0; i < num_phys; i++) {
+             err = usb_phy_roothub_add_phy(dev, i, &phy_roothub->list);
+             if (err)
+                     goto err_out;
+     }
+
+     head = &phy_roothub->list;
+
+     list_for_each_entry(roothub_entry, head, list) {
+             err = phy_init(roothub_entry->phy);

The phy_init() function actually enables the PHY clocks.
It should be moved to the usb_phy_roothub_exit() routine just before calling phy_power_on().

do you mean that phy_init should be moved to usb_phy_roothub_power_on
(just before phy_power_on is called within usb_phy_roothub_power_on)?

Yes.

quoted

an earlier version of my patch did exactly this, but it caused
problems during a suspend/resume cycle on Mediatek devices
Chunfeng Yun reported that issue here [0], quote from that mail for
easier reading:
"In order to keep link state on mt8173, we just power off all phys(not
exit) when system enter suspend, then power on them again (needn't
init, otherwise device will be disconnected) when system resume, this
can avoid re-enumerating device."

quoted

quoted

+             if (err)
+                     goto err_exit_phys;
+     }
+
+     return phy_roothub;
+
+err_exit_phys:
+     list_for_each_entry_continue_reverse(roothub_entry, head, list)
+             phy_exit(roothub_entry->phy);
+
+err_out:
+     return ERR_PTR(err);
+}
+EXPORT_SYMBOL_GPL(usb_phy_roothub_init);
+
+int usb_phy_roothub_exit(struct usb_phy_roothub *phy_roothub)
+{
+     struct usb_phy_roothub *roothub_entry;
+     struct list_head *head;
+     int err, ret = 0;
+
+     if (!phy_roothub)
+             return 0;
+
+     head = &phy_roothub->list;
+
+     list_for_each_entry(roothub_entry, head, list) {
+             err = phy_exit(roothub_entry->phy);
+             if (err)
+                     ret = ret;
+     }

phy_exit() should be moved to usb_phy_roothub_poweroff() just after calling phy_power_off().

if I understood Chunfeng Yun correctly this will require
re-enumeration of the USB devices after a suspend/resume cycle on
Mediatek SoCs

OK. I suppose that there are 2 cases
1) Mediatek's case: USB controller context retained across suspend/resume.
Remote wakeup probably required.
No re-enumeration preferred after resume. phy_exit()/phy_init() must not be called
during suspend/resume to keep PHY link active.

Documentation/devicetree/bindings/usb/mediatek,mtu3.txt indeed shows
that the parent of the USB controller can be marked as "wakeup-source"

quoted

2) TI's case: low power important: USB context is lost, OK to re-enumerate.
phy_exit()/phy_init() must be called during suspend/resume.

ACK

quoted

quoted

quoted

With that there is nothing else being done here. Shouldn't we be doing the equivalent of
usb_phy_roothub_del_phy() and usb_phy_roothub_free() here?

quoted

+
+     return ret;
+}
+EXPORT_SYMBOL_GPL(usb_phy_roothub_exit);
+
+int usb_phy_roothub_power_on(struct usb_phy_roothub *phy_roothub)
+{
+     struct usb_phy_roothub *roothub_entry;
+     struct list_head *head;
+     int err;
+
+     if (!phy_roothub)
+             return 0;
+
+     head = &phy_roothub->list;
+
+     list_for_each_entry(roothub_entry, head, list) {
+             err = phy_power_on(roothub_entry->phy);
+             if (err)
+                     goto err_out;
+     }
+
+     return 0;
+
+err_out:
+     list_for_each_entry_continue_reverse(roothub_entry, head, list)
+             phy_power_off(roothub_entry->phy);
+
+     return err;
+}
+EXPORT_SYMBOL_GPL(usb_phy_roothub_power_on);
+
+void usb_phy_roothub_power_off(struct usb_phy_roothub *phy_roothub)
+{
+     struct usb_phy_roothub *roothub_entry;
+
+     if (!phy_roothub)
+             return;
+
+     list_for_each_entry_reverse(roothub_entry, &phy_roothub->list, list)
+             phy_power_off(roothub_entry->phy);

Not doing the phy_exit() here leaves the clocks enabled on our SoC and
we're no longer able to reach low power states on system suspend.

I'm not sure where this problem should be solved:
- set skip_phy_initialization in struct usb_hcd to 1 for the affected
TI platforms

Many TI platforms are affected, omap5*, dra7*, am43*

quoted

- fix this in the usb_phy_roothub code

I'd vote for fixing it in the usb_phy_roothub code. How?
How about using the device_can_wakeup() to decide if we should call phy_exit()/init() or not?
If the USB device can't wakeup the system there is no point in keeping it powered/clocked right?

@Chunfeng: can you confirm Roger's idea that we could call phy_exit if
the controller is *NOT* marked as "wakeup-source"?
I am also not sure if it would work, since the "wakeup-source"
property is defined on the USB controller's parent node in case of the
Mediatek MTU3 (Mediatek USB3.0 DRD) controller

Very sorry, I forgot that MTU3 & xHCI drivers always set them as wakeup
devices by device_init_wakeup(dev, true),but not dependent on
"wakeup-source" property, so maybe we can use device_can_wakeup() to
decide whether call phy_exit()/init() or not.

the 64-bit Amlogic Meson GXL/GXM SoCs don't support suspend/resume
yet, so I cannot test this
based on this suggestion I threw up two patches which are *compile
tested only* based on Greg's usb-next branch
you can find them here: [0] (as well as attached to this mail)

@Chunfeng: can you please test this on one of your Mediatek SoCs?
@Roger: can you please test this on a TI SoC?

(apologies in advance if these patches don't work)

please note that I won't have access to my computer until Saturday.
if these patches need to be rewritten/replaced/etc. then feel free to
send your own version to the list

Had to do the following to build

diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index 6d4a419..2884607 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c

@@ -2262,7 +2262,7 @@ int hcd_bus_suspend(struct usb_device *rhdev, pm_message_t msg)
 		hcd->state = HC_STATE_SUSPENDED;
 
 		if (!PMSG_IS_AUTO(msg))
-			usb_phy_roothub_suspend(hcd->phy_roothub);
+			usb_phy_roothub_suspend(&rhdev->dev, hcd->phy_roothub);

Try to use hcd->self.controller instead of &rhdev->dev;

Actually it should be hcd->self.sysdev.

quoted

 
 		/* Did we race with a root-hub wakeup event? */
 		if (rhdev->do_remote_wakeup) {

@@ -2302,7 +2302,7 @@ int hcd_bus_resume(struct usb_device *rhdev, pm_message_t msg)
 	}
 
 	if (!PMSG_IS_AUTO(msg)) {
-		status = usb_phy_roothub_resume(hcd->phy_roothub);
+		status = usb_phy_roothub_resume(&rhdev->dev, hcd->phy_roothub);

ditto

quoted

 		if (status)
 			return status;
 	}

@@ -2344,7 +2344,7 @@ int hcd_bus_resume(struct usb_device *rhdev, pm_message_t msg)
 		}
 	} else {
 		hcd->state = old_state;
-		usb_phy_roothub_suspend(hcd->phy_roothub);
+		usb_phy_roothub_suspend(&rhdev->dev, hcd->phy_roothub);

ditto

quoted

 		dev_dbg(&rhdev->dev, "bus %s fail, err %d\n",
 				"resume", status);
 		if (status != -ESHUTDOWN)


And the following to fix runtime issues

diff --git a/drivers/usb/core/phy.c b/drivers/usb/core/phy.c
index 2eca371..8598906 100644
--- a/drivers/usb/core/phy.c
+++ b/drivers/usb/core/phy.c

@@ -32,9 +32,9 @@ static int usb_phy_roothub_add_phy(struct device *dev, int index,
 			return PTR_ERR(phy);
 	}
 
-	roothub_entry = usb_phy_roothub_alloc(dev);
-	if (IS_ERR(roothub_entry))
-		return PTR_ERR(roothub_entry);
+	roothub_entry = devm_kzalloc(dev, sizeof(*roothub_entry), GFP_KERNEL);
+	if (!roothub_entry)
+		return -ENOMEM;
 
 	roothub_entry->phy = phy;
 

@@ -162,7 +162,7 @@ int usb_phy_roothub_suspend(struct device *dev,
 	usb_phy_roothub_power_off(phy_roothub);
 
 	/* keep the PHYs initialized so the device can wake up the system */
-	if (device_can_wakeup(dev))
+	if (device_may_wakeup(dev))

It's ok

I had to additionally fix usb_phy_roothub_resume() from
	if (device_can_wakeup(dev))
to
	if (!device_may_wakeup(dev))

quoted

 		return 0;
 
 	return usb_phy_roothub_exit(phy_roothub);


Here are my obervations
- if wakeup is disabled it works fine as expected, phy_exit() is called and I'm able to reach
low power states.

- if wakeup is enabled (/sys/bus/usb/device/usb2/power/wakeup), then hcd_bus_suspend() is never called
and so phy_power_off won't be called either.

This means that the device_may_wakeup() check is redundant. Sorry for suggesting this.

You maybe use a wrong device.

Yes, after using the correct device I don't see the problem.

Can you please try the below patch on top of the 2 Patches that Martin sent and the new patch you sent?
Once you confirm it works for you I can send the 2 patches officially.

diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index 6d4a419..04cc453 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c

@@ -2262,7 +2262,7 @@ int hcd_bus_suspend(struct usb_device *rhdev, pm_message_t msg)
 		hcd->state = HC_STATE_SUSPENDED;
 
 		if (!PMSG_IS_AUTO(msg))
-			usb_phy_roothub_suspend(hcd->phy_roothub);
+			usb_phy_roothub_suspend(hcd->self.sysdev, hcd->phy_roothub);
 
 		/* Did we race with a root-hub wakeup event? */
 		if (rhdev->do_remote_wakeup) {

@@ -2302,7 +2302,7 @@ int hcd_bus_resume(struct usb_device *rhdev, pm_message_t msg)
 	}
 
 	if (!PMSG_IS_AUTO(msg)) {
-		status = usb_phy_roothub_resume(hcd->phy_roothub);
+		status = usb_phy_roothub_resume(hcd->self.sysdev, hcd->phy_roothub);
 		if (status)
 			return status;
 	}

@@ -2344,7 +2344,7 @@ int hcd_bus_resume(struct usb_device *rhdev, pm_message_t msg)
 		}
 	} else {
 		hcd->state = old_state;
-		usb_phy_roothub_suspend(hcd->phy_roothub);
+		usb_phy_roothub_suspend(hcd->self.sysdev, hcd->phy_roothub);
 		dev_dbg(&rhdev->dev, "bus %s fail, err %d\n",
 				"resume", status);
 		if (status != -ESHUTDOWN)

diff --git a/drivers/usb/core/phy.c b/drivers/usb/core/phy.c
index 2eca371..25fe729 100644
--- a/drivers/usb/core/phy.c
+++ b/drivers/usb/core/phy.c

@@ -32,9 +32,9 @@ static int usb_phy_roothub_add_phy(struct device *dev, int index,
 			return PTR_ERR(phy);
 	}
 
-	roothub_entry = usb_phy_roothub_alloc(dev);
-	if (IS_ERR(roothub_entry))
-		return PTR_ERR(roothub_entry);
+	roothub_entry = devm_kzalloc(dev, sizeof(*roothub_entry), GFP_KERNEL);
+	if (!roothub_entry)
+		return -ENOMEM;
 
 	roothub_entry->phy = phy;
 

@@ -162,7 +162,7 @@ int usb_phy_roothub_suspend(struct device *dev,
 	usb_phy_roothub_power_off(phy_roothub);
 
 	/* keep the PHYs initialized so the device can wake up the system */
-	if (device_can_wakeup(dev))
+	if (device_may_wakeup(dev))
 		return 0;
 
 	return usb_phy_roothub_exit(phy_roothub);

@@ -175,7 +175,7 @@ int usb_phy_roothub_resume(struct device *dev,
 	int err;
 
 	/* if the device can't wake up the system _exit was called */
-	if (device_can_wakeup(dev)) {
+	if (!device_may_wakeup(dev)) {
 		err = usb_phy_roothub_init(phy_roothub);
 		if (err)
 			return err;

-- 
cheers,
-roger

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki