[RESEND PATCH v3 1/5] dt-bindings: i2c-stm32: Document the STM32F7 I2C bindings
From: Pierre-Yves MORDRET <hidden>
Date: 2017-09-01 07:35:24
Also in:
linux-arm-kernel, linux-i2c, lkml
Subsystem:
i2c subsystem host drivers, open firmware and flattened device tree bindings, the rest · Maintainers:
Andi Shyti, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds
This patch adds the documentation of device tree bindings for STM32F7 I2C
Signed-off-by: M'boumba Cedric Madianga <redacted>
Signed-off-by: Pierre-Yves MORDRET <redacted>
Acked-by: Rob Herring <robh@kernel.org>
---
Version history:
v3:
* None
v2:
* Remove i2c-timing binding in order to use generic bindings SCL
Rising and Falling time instead
---
---
.../devicetree/bindings/i2c/i2c-stm32.txt | 29 +++++++++++++++++++---
1 file changed, 26 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
index 78eaf7b..3b54899 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt@@ -1,7 +1,9 @@ * I2C controller embedded in STMicroelectronics STM32 I2C platform Required properties : -- compatible : Must be "st,stm32f4-i2c" +- compatible : Must be one of the following + - "st,stm32f4-i2c" + - "st,stm32f7-i2c" - reg : Offset and length of the register set for the device - interrupts : Must contain the interrupt id for I2C event and then the interrupt id for I2C error.
@@ -14,8 +16,16 @@ Required properties : Optional properties : - clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, - the default 100 kHz frequency will be used. As only Normal and Fast modes - are supported, possible values are 100000 and 400000. + the default 100 kHz frequency will be used. + For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are + 100000 and 400000. + For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, + possible values are 100000, 400000 and 1000000. +- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board + (default: 25) +- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board + (default: 10) + I2C Timings are derived from these 2 values Example :
@@ -31,3 +41,16 @@ Example : pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>; pinctrl-names = "default"; }; + + i2c@40005400 { + compatible = "st,stm32f7-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40005400 0x400>; + interrupts = <31>, + <32>; + resets = <&rcc STM32F7_APB1_RESET(I2C1)>; + clocks = <&rcc 1 CLK_I2C1>; + pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>; + pinctrl-names = "default"; + };
--
2.7.4