On Thu, Aug 11, 2016 at 04:34:05PM -0500, Timur Tabi wrote:

Add supports for ethernet controller HW on Qualcomm Technologies, Inc. SoC.
This driver supports the following features:
1) Checksum offload.
2) Interrupt coalescing support.
3) SGMII phy.
4) phylib interface for external phy

Based on original work by
	Niranjana Vishwanathapura [off-list ref]
	Gilad Avidov [off-list ref]

Signed-off-by: Timur Tabi <redacted>
---

v8:
 - Remove "phy-version" property, use different compatible strings to
   differentiate EMAC versions instead.
 - fully unmap all DMA mappings upon any single DMA mapping error
 - add support for 32-bit DMA masks
 - Make reads/writes to hardware data structures endian-safe
 - emac_mac_stop already disables interrupts, so don't do it in emac_mac_reset
 - Set adpt->rxbuf_size only when initializing the MAC, not when changing MTU
 - Fix the calculation of the # of free descriptors required
 - Always stop the PHY before disconnecting it
 - Miscellaneous cleanups (removing unused definitions, fix typos and spacing,
   use unsized ints, etc).

v7:
 - add "phy-version" to DT docs
 - remove emac_status_bits, use mutexes instead of polling a status bit
 - test return code from dma_map_single() calls
 - use __netdev_alloc_skb_ip_align instead of dev_alloc_skb
 - add a missing free_irq on an error path
 - return an error code from emac_reinit_locked
 - support setting the MTU even when the interface is down
 - use a spinlock not a mutex in emac_get_stats64
 - don't redundantly set the ethernet device name
 - remove all hardware timestamp code, since it's incomplete
 - remove redundant 'reset' param to emac_mac_down()
 - handle queue throttling properly

v6:
 - Properly ordered local variables
 - use built-in GEN_MASK instead of BITS_MASK
 - remove redundant call to emac_rx_mode_set from emac_mac_up
 - removed emac_rfd structure, use dma_addr_t directly instead
 - removed emac_mac_speed enun, replaced with macros
 - removed superfluous phy_stop from emac_mac_down(), which prevented reloading module
 - add missing netif_napi_del
 - set the DMA mask

v5:
 - changed author to Timur, added MAINTAINERS entry
 - use phylib, replacing internal phy code
 - added support for EMAC internal SGMII v2
 - fix ~DIS_INT warning
 - update DT bindings, including removing unused properties
 - removed interrupt handler for internal sgmii
 - removed link status check handler/state (replaced with phylib)
 - removed periodic timer handler (replaced with phylib)
 - removed power management code (will be rewritten later)
 - external phy is now required, not optional
 - removed redundant EMAC_STATUS_DOWN status flag
 - removed redundant link status and speed variables
 - removed redundant status bits (vlan strip, promiscuous, loopback, etc)
 - removed useless watchdog status
 - removed command-line parameters
 - cleaned up probe messages
 - removed redundant params from emac_sgmii_link_init()
 - always call netdev_completed_queue() (per review comment)
 - fix emac_napi_rtx() (per review comment)
 - removed max_ints loop in interrupt handler
 - removed redundant mutex around phy read/write calls
 - added lock for reading emac status (per review comment)
 - generate random MAC address if it can't be read from firmware
 - replace EMAC_DMA_ADDR_HI/LO with upper/lower_32_bits
 - don't test return value from platform_get_resource (per review comment)
 - use net_warn_ratelimited (per review comment)
 - don't set the dma masks (will be set by DT or IORT code)
 - remove unused emac_tx_tpd_ts_save()
 - removed redundant local MTU variable

v4:
 - add missing ipv6 header file
 - correct compatible string
 - fix spacing in emac_reg_write arrays
 - drop unnecessary cell-index property
 - remove unsupported DT properties from docs
 - remove GPIO initialization and update docs

v3:
 - remove most of the memory barriers by using the non xxx_relaxed() api.
 - remove RSS and WOL support.
 - correct comments from physical address to dma address.
 - rearrange structs to make them packed.
 - replace polling loops with readl_poll_timeout().
 - remove unnecessary wrapper functions from phy layer.
 - add blank line before return statements.
 - set to null clocks after clk_put().
 - use module_platform_driver() and dma_set_mask_and_coherent()
 - replace long hex bitmasks with BIT() macro.

v2:
 - replace hw bit fields to macros with bitwise operations.
 - change all iterators to unsized types (int)
 - some minor code flow improvements.
 - change return type to void for functions which return value is never
   used.
 - replace instance of xxxxl_relaxed() io followed by mb() with a
   readl()/writel().

 .../devicetree/bindings/net/qcom-emac.txt          |   64 +

Acked-by: Rob Herring <robh@kernel.org>

 MAINTAINERS                                        |    6 +
 drivers/net/ethernet/qualcomm/Kconfig              |   11 +
 drivers/net/ethernet/qualcomm/Makefile             |    2 +
 drivers/net/ethernet/qualcomm/emac/Makefile        |    7 +
 drivers/net/ethernet/qualcomm/emac/emac-mac.c      | 1532 ++++++++++++++++++++
 drivers/net/ethernet/qualcomm/emac/emac-mac.h      |  250 ++++
 drivers/net/ethernet/qualcomm/emac/emac-phy.c      |  201 +++
 drivers/net/ethernet/qualcomm/emac/emac-phy.h      |   32 +
 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c    |  693 +++++++++
 drivers/net/ethernet/qualcomm/emac/emac-sgmii.h    |   24 +
 drivers/net/ethernet/qualcomm/emac/emac.c          |  796 ++++++++++
 drivers/net/ethernet/qualcomm/emac/emac.h          |  335 +++++
 13 files changed, 3953 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/qcom-emac.txt
 create mode 100644 drivers/net/ethernet/qualcomm/emac/Makefile
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-mac.c
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-mac.h
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-phy.c
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-phy.h
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii.h
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac.c
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac.h