On Thu, 2016-08-25 at 11:05 +0800, Chunfeng Yun wrote:

This patch adds support for the MediaTek USB3 controller
integrated into MT8173. It can be configured as Dual-Role
Device (DRD), Peripheral Only and Host Only (xHCI) modes.

+/**
+ * General Purpose Descriptor (GPD):
+ *	The format of TX GPD is a little different from RX one.
+ *	And the size of GPD is 16 bytes.
+ *
+ * @flag:
+ *	bit0: Hardware Own (HWO)
+ *	bit1: Buffer Descriptor Present (BDP), always 0, BD is not supported
+ *	bit2: Bypass (BPS), 1: HW skips this GPD if HWO = 1
+ *	bit7: Interrupt On Completion (IOC)
+ * @chksum: This is used to validate the contents of this GPD;
+ *	If TXQ_CS_EN / RXQ_CS_EN bit is set, an interrupt is issued
+ *	when checksum validation fails;
+ *	Checksum value is calculated over the 16 bytes of the GPD by default;
+ * @data_buf_len (RX ONLY): This value indicates the length of
+ *	the assigned data buffer
+ * @next_gpd: Physical address of the next GPD
+ * @buffer: Physical address of the data buffer
+ * @buf_len:
+ *	(TX): This value indicates the length of the assigned data buffer
+ *	(RX): The total length of data received
+ * @ext_len: reserved
+ * @ext_flag:
+ *	bit5 (TX ONLY): Zero Length Packet (ZLP),
+ */
+struct qmu_gpd {
+	u8 flag;
+	u8 chksum;
+	u16 data_buf_len;
+	u32 next_gpd;
+	u32 buffer;
+	u16 buf_len;
+	u8 ext_len;
+	u8 ext_flag;
+} __packed;

It looks like this is shared with hardware in memory.
But you leave the endianness of the bigger fields undeclared.

+/**
+* dma: physical base address of GPD segment
+* start: virtual base address of GPD segment
+* end: the last GPD element
+* enqueue: the first empty GPD to use
+* dequeue: the first completed GPD serviced by ISR
+* NOTE: the size of GPD ring should be >= 2
+*/
+struct mtu3_gpd_ring {
+	dma_addr_t dma;
+	struct qmu_gpd *start;
+	struct qmu_gpd *end;
+	struct qmu_gpd *enqueue;
+	struct qmu_gpd *dequeue;
+};
+
+/**
+* @vbus: vbus 5V used by host mode
+* @edev: external connector used to detect vbus and iddig changes
+* @vbus_nb: notifier for vbus detection
+* @vbus_nb: notifier for iddig(idpin) detection
+* @extcon_reg_dwork: delay work for extcon notifier register, waiting for
+*		xHCI driver initialization, it's necessary for system bootup
+*		as device.
+* @is_u3_drd: whether port0 supports usb3.0 dual-role device or not
+* @id_*: used to maually switch between host and device modes by idpin
+* @manual_drd_enabled: it's true when supports dual-role device by debugfs
+*		to switch host/device modes depending on user input.

Please use a common interface for this. The Intel people are introducing
one.

If you use the "f" option to dynamic debugging it will give you the
function name anyway. So why include __func__ ?

+/* enable/disable U3D SS function */
+static void mtu3_ss_func_set(struct mtu3 *mtu, bool enable)

Inline maybe ?

+{
+	/* If usb3_en==0, LTSSM will go to SS.Disable state */
+	if (enable)
+		mtu3_setbits(mtu->mac_base, U3D_USB3_CONFIG, USB3_EN);
+	else
+		mtu3_clrbits(mtu->mac_base, U3D_USB3_CONFIG, USB3_EN);
+
+	dev_dbg(mtu->dev, "USB3_EN = %d\n", !!enable);
+}
+

[..]

+int mtu3_config_ep(struct mtu3 *mtu, struct mtu3_ep *mep,
+			int interval, int burst, int mult)
+{
+	void __iomem *mbase = mtu->mac_base;
+	int epnum = mep->epnum;
+	u32 csr0, csr1, csr2;
+	int fifo_sgsz, fifo_addr;
+	int num_pkts;
+
+	fifo_addr = ep_fifo_alloc(mep, mep->maxp);
+	if (fifo_addr < 0) {
+		dev_err(mtu->dev, "alloc ep fifo failed(%d)\n", mep->maxp);
+		return -ENOMEM;
+	}
+	fifo_sgsz = ilog2(mep->fifo_seg_size);
+	dev_dbg(mtu->dev, "%s fifosz: %x(%x/%x)\n", __func__, fifo_sgsz,
+		mep->fifo_seg_size, mep->fifo_size);
+
+	if (mep->is_in) {
+		csr0 = TX_TXMAXPKTSZ(mep->maxp);
+		csr0 |= TX_DMAREQEN;
+
+		num_pkts = (burst + 1) * (mult + 1) - 1;
+		csr1 = TX_SS_BURST(burst) | TX_SLOT(mep->slot);
+		csr1 |= TX_MAX_PKT(num_pkts) | TX_MULT(mult);
+
+		csr2 = TX_FIFOADDR(fifo_addr >> 4);
+		csr2 |= TX_FIFOSEGSIZE(fifo_sgsz);
+
+		switch (mep->type) {
+		case USB_ENDPOINT_XFER_BULK:
+			csr1 |= TX_TYPE(TYPE_BULK);
+			break;
+		case USB_ENDPOINT_XFER_ISOC:
+			csr1 |= TX_TYPE(TYPE_ISO);
+			csr2 |= TX_BINTERVAL(interval);
+			break;
+		case USB_ENDPOINT_XFER_INT:
+			csr1 |= TX_TYPE(TYPE_INT);
+			csr2 |= TX_BINTERVAL(interval);
+			break;

And if it is control?

+		}
+
+		/* Enable QMU Done interrupt */
+		mtu3_setbits(mbase, U3D_QIESR0, QMU_TX_DONE_INT(epnum));
+
+		mtu3_writel(mbase, MU3D_EP_TXCR0(epnum), csr0);
+		mtu3_writel(mbase, MU3D_EP_TXCR1(epnum), csr1);
+		mtu3_writel(mbase, MU3D_EP_TXCR2(epnum), csr2);
+
+		dev_dbg(mtu->dev, "U3D_TX%d CSR0:%#x, CSR1:%#x, CSR2:%#x\n",
+			epnum, mtu3_readl(mbase, MU3D_EP_TXCR0(epnum)),
+			mtu3_readl(mbase, MU3D_EP_TXCR1(epnum)),
+			mtu3_readl(mbase, MU3D_EP_TXCR2(epnum)));
+	} else {
+		csr0 = RX_RXMAXPKTSZ(mep->maxp);
+		csr0 |= RX_DMAREQEN;
+
+		num_pkts = (burst + 1) * (mult + 1) - 1;
+		csr1 = RX_SS_BURST(burst) | RX_SLOT(mep->slot);
+		csr1 |= RX_MAX_PKT(num_pkts) | RX_MULT(mult);
+
+		csr2 = RX_FIFOADDR(fifo_addr >> 4);
+		csr2 |= RX_FIFOSEGSIZE(fifo_sgsz);
+
+		switch (mep->type) {
+		case USB_ENDPOINT_XFER_BULK:
+			csr1 |= RX_TYPE(TYPE_BULK);
+			break;
+		case USB_ENDPOINT_XFER_ISOC:
+			csr1 |= RX_TYPE(TYPE_ISO);
+			csr2 |= RX_BINTERVAL(interval);
+			break;
+		case USB_ENDPOINT_XFER_INT:
+			csr1 |= RX_TYPE(TYPE_INT);
+			csr2 |= RX_BINTERVAL(interval);
+			break;

Again: control endpoints?

+		}
+
+		/*Enable QMU Done interrupt */
+		mtu3_setbits(mbase, U3D_QIESR0, QMU_RX_DONE_INT(epnum));
+
+		mtu3_writel(mbase, MU3D_EP_RXCR0(epnum), csr0);
+		mtu3_writel(mbase, MU3D_EP_RXCR1(epnum), csr1);
+		mtu3_writel(mbase, MU3D_EP_RXCR2(epnum), csr2);
+
+		dev_dbg(mtu->dev, "U3D_RX%d CSR0:%#x, CSR1:%#x, CSR2:%#x\n",
+			epnum, mtu3_readl(mbase, MU3D_EP_RXCR0(epnum)),
+			mtu3_readl(mbase, MU3D_EP_RXCR1(epnum)),
+			mtu3_readl(mbase, MU3D_EP_RXCR2(epnum)));
+	}
+
+	dev_dbg(mtu->dev, "csr0:%#x, csr1:%#x, csr2:%#x\n", csr0, csr1, csr2);
+	dev_dbg(mtu->dev, "%s: %s, fifo-addr:%#x, fifo-size:%#x(%#x/%#x)\n",
+		__func__, mep->name, mep->fifo_addr, mep->fifo_size,
+		fifo_sgsz, mep->fifo_seg_size);
+
+	return 0;
+}
+

[..]

+static void mtu3_set_speed(struct mtu3 *mtu)
+{
+	void __iomem *mbase = mtu->mac_base;
+
+	if (!mtu->is_u3_ip && (mtu->max_speed > USB_SPEED_HIGH))
+		mtu->max_speed = USB_SPEED_HIGH;

You are missing the checks for USB_SPEED_WIRELESS in general.
Can you just ignore it?

+
+	if (mtu->max_speed == USB_SPEED_FULL) {
+		/* disable U3 SS function */
+		mtu3_clrbits(mbase, U3D_USB3_CONFIG, USB3_EN);
+		/* disable HS function */
+		mtu3_clrbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
+	} else if (mtu->max_speed == USB_SPEED_HIGH) {
+		mtu3_clrbits(mbase, U3D_USB3_CONFIG, USB3_EN);
+		/* HS/FS detected by HW */
+		mtu3_setbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
+	}
+	dev_info(mtu->dev, "max_speed: %s\n",
+		usb_speed_string(mtu->max_speed));
+}

[..]

+static irqreturn_t mtu3_link_isr(struct mtu3 *mtu)
+{
+	void __iomem *mbase = mtu->mac_base;
+	enum usb_device_speed udev_speed;
+	u32 maxpkt = 64;
+	u32 link;
+	u32 speed;
+
+	link = mtu3_readl(mbase, U3D_DEV_LINK_INTR);
+	link &= mtu3_readl(mbase, U3D_DEV_LINK_INTR_ENABLE);
+	mtu3_writel(mbase, U3D_DEV_LINK_INTR, link); /* W1C */
+	dev_dbg(mtu->dev, "=== LINK[%x] ===\n", link);
+
+	if (!(link & SSUSB_DEV_SPEED_CHG_INTR))
+		return IRQ_NONE;

Shouldn't you do this check before you clear interrupts?

+	speed = SSUSB_DEV_SPEED(mtu3_readl(mbase, U3D_DEVICE_CONF));

Do you really want to read this out of the hardware on every interrupt?

+
+	switch (speed) {
+	case MTU3_SPEED_FULL:
+		udev_speed = USB_SPEED_FULL;
+		/*BESLCK = 4 < BESLCK_U3 = 10 < BESLDCK = 15 */
+		mtu3_writel(mbase, U3D_USB20_LPM_PARAMETER, LPM_BESLDCK(0xf)
+				| LPM_BESLCK(4) | LPM_BESLCK_U3(0xa));
+		mtu3_setbits(mbase, U3D_POWER_MANAGEMENT,
+				LPM_BESL_STALL | LPM_BESLD_STALL);
+		break;
+	case MTU3_SPEED_HIGH:
+		udev_speed = USB_SPEED_HIGH;
+		/*BESLCK = 4 < BESLCK_U3 = 10 < BESLDCK = 15 */
+		mtu3_writel(mbase, U3D_USB20_LPM_PARAMETER, LPM_BESLDCK(0xf)
+				| LPM_BESLCK(4) | LPM_BESLCK_U3(0xa));
+		mtu3_setbits(mbase, U3D_POWER_MANAGEMENT,
+				LPM_BESL_STALL | LPM_BESLD_STALL);
+		break;
+	case MTU3_SPEED_SUPER:
+		udev_speed = USB_SPEED_SUPER;
+		maxpkt = 512;
+		break;
+	default:
+		udev_speed = USB_SPEED_UNKNOWN;
+		break;
+	}
+	dev_dbg(mtu->dev, "%s: %s\n", __func__, usb_speed_string(udev_speed));
+
+	mtu->g.speed = udev_speed;
+	mtu->g.ep0->maxpacket = maxpkt;
+	mtu->ep0_state = MU3D_EP0_STATE_SETUP;
+
+	if (udev_speed == USB_SPEED_UNKNOWN)
+		mtu3_gadget_disconnect(mtu);
+	else
+		mtu3_ep0_setup(mtu);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t mtu3_u3_ltssm_isr(struct mtu3 *mtu)
+{
+	void __iomem *mbase = mtu->mac_base;
+	u32 ltssm;
+
+	ltssm = mtu3_readl(mbase, U3D_LTSSM_INTR);
+	ltssm &= mtu3_readl(mbase, U3D_LTSSM_INTR_ENABLE);
+	mtu3_writel(mbase, U3D_LTSSM_INTR, ltssm); /* W1C */
+	dev_dbg(mtu->dev, "=== LTSSM[%x] ===\n", ltssm);
+
+	if (ltssm & HOT_RST_INTR)
+		mtu3_gadget_reset(mtu);
+
+	if (ltssm & WARM_RST_INTR)
+		mtu3_gadget_reset(mtu);

You really would reset the gadget twice if that happens?
And do the rest of the tests make sense in that case?

+
+	if (ltssm & VBUS_FALL_INTR)
+		mtu3_ss_func_set(mtu, false);
+
+	if (ltssm & VBUS_RISE_INTR)
+		mtu3_ss_func_set(mtu, true);
+
+	if (ltssm & EXIT_U3_INTR)
+		mtu3_gadget_resume(mtu);
+
+	if (ltssm & ENTER_U3_INTR)
+		mtu3_gadget_suspend(mtu);
+
+	return IRQ_HANDLED;
+}

[..]

+static int mtu3_hw_init(struct mtu3 *mtu)
+{
+	int ret;
+
+	mtu3_device_reset(mtu);
+
+	ret = mtu3_device_enable(mtu);
+	if (ret) {
+		dev_err(mtu->dev, "device enable failed %d\n", ret);
+		return ret;
+	}
+
+	ret = mtu3_mem_alloc(mtu);
+	if (ret) {
+		dev_err(mtu->dev, "mem alloc failed, aborting\n");

1. You can't leave the device enabled in that case.
2. No need for a message. The kernel will already do that if kmalloc()
fails under such circumstances.

+		return -ENOMEM;
+	}
+
+	mtu3_regs_init(mtu);
+
+	return 0;
+}

No proper error returns

+
+	return count;
+}
+
+static const struct file_operations ssusb_mode_fops = {
+	.open = ssusb_mode_open,
+	.write = ssusb_mode_write,
+	.read = seq_read,
+	.llseek = seq_lseek,
+	.release = single_release,
+};
+
+static void ssusb_debugfs_init(struct ssusb_mtk *ssusb)
+{
+	struct dentry *root;
+	struct dentry *file;
+
+	root = debugfs_create_dir(dev_name(ssusb->dev), usb_debug_root);
+	if (IS_ERR_OR_NULL(root)) {
+		if (!root)
+			dev_err(ssusb->dev, "create debugfs root failed\n");
+		return;
+	}
+	ssusb->dbgfs_root = root;
+
+	file = debugfs_create_file("mode", S_IRUGO | S_IWUSR, root,
+			ssusb, &ssusb_mode_fops);
+	if (!file)
+		dev_dbg(ssusb->dev, "create debugfs mode failed\n");
+}
+
+static void ssusb_debugfs_exit(struct ssusb_mtk *ssusb)
+{
+	debugfs_remove_recursive(ssusb->dbgfs_root);
+}
+
+int ssusb_otg_switch_init(struct ssusb_mtk *ssusb)
+{
+	struct otg_switch_mtk *otg_sx = &ssusb->otg_switch;
+
+	INIT_DELAYED_WORK(&otg_sx->extcon_reg_dwork, extcon_register_dwork);
+
+	if (otg_sx->manual_drd_enabled)
+		ssusb_debugfs_init(ssusb);
+
+	/* It is enough to delay 1s for waiting for host initialization */
+	schedule_delayed_work(&otg_sx->extcon_reg_dwork, HZ);

You need to handle this still pending when you are deregistered.

+
+	return 0;
+}
+
+void ssusb_otg_switch_exit(struct ssusb_mtk *ssusb)
+{
+	struct otg_switch_mtk *otg_sx = &ssusb->otg_switch;
+
+	if (otg_sx->edev) {
+		extcon_unregister_notifier(otg_sx->edev,
+			EXTCON_USB, &otg_sx->vbus_nb);
+		extcon_unregister_notifier(otg_sx->edev,
+			EXTCON_USB_HOST, &otg_sx->id_nb);
+	}
+
+	if (otg_sx->manual_drd_enabled)
+		ssusb_debugfs_exit(ssusb);
+}

Could you break this up a bit? It is extensively long a patch?

	Regards
		Oliver