[PATCH v3 27/27] ARM: dts: exynos: Add RTC and I2C to Exynos5410
From: Krzysztof Kozlowski <krzk@kernel.org>
Date: 2016-05-10 20:11:55
Also in:
linux-arm-kernel, linux-clk, linux-samsung-soc, lkml
Subsystem:
the rest · Maintainer:
Linus Torvalds
Configure Exynos5410-specific properties of RTC, I2C and HSI2C nodes. This still does not enable them on the board level though. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> --- arch/arm/boot/dts/exynos5410.dtsi | 66 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 66 insertions(+)
diff --git a/arch/arm/boot/dts/exynos5410.dtsi b/arch/arm/boot/dts/exynos5410.dtsi
index dd4d6d752865..ae64cb0a8efd 100644
--- a/arch/arm/boot/dts/exynos5410.dtsi
+++ b/arch/arm/boot/dts/exynos5410.dtsi@@ -114,6 +114,9 @@ status = "disabled"; }; + /* i2c_0-3 are defined in exynos5.dtsi */ + /* hsi2c_4-7 are defined in exynos5xx.dtsi */ + pinctrl_0: pinctrl@13400000 { compatible = "samsung,exynos5410-pinctrl"; reg = <0x13400000 0x1000>;
@@ -146,6 +149,62 @@ }; }; +&i2c_0 { + clocks = <&clock CLK_I2C0>; + clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_bus>; +}; + +&i2c_1 { + clocks = <&clock CLK_I2C1>; + clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_bus>; +}; + +&i2c_2 { + clocks = <&clock CLK_I2C2>; + clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_bus>; +}; + +&i2c_3 { + clocks = <&clock CLK_I2C3>; + clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_bus>; +}; + +&hsi2c_4 { + clocks = <&clock CLK_USI0>; + clock-names = "hsi2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_hs_bus>; +}; + +&hsi2c_5 { + clocks = <&clock CLK_USI1>; + clock-names = "hsi2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_hs_bus>; +}; + +&hsi2c_6 { + clocks = <&clock CLK_USI2>; + clock-names = "hsi2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c6_hs_bus>; +}; + +&hsi2c_7 { + clocks = <&clock CLK_USI3>; + clock-names = "hsi2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c7_hs_bus>; +}; + &mct { clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>; clock-names = "fin_pll", "mct";
@@ -156,6 +215,13 @@ clock-names = "timers"; }; +&rtc { + clocks = <&clock CLK_RTC>; + clock-names = "rtc"; + interrupt-parent = <&pmu_system_controller>; + status = "disabled"; +}; + &serial_0 { clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>; clock-names = "uart", "clk_uart_baud0";
--
2.5.0