Re: [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules
From: Lothar Waßmann <hidden>
Date: 2016-03-31 06:30:40
Also in:
linux-arm-kernel, lkml
Hi, On Thu, 31 Mar 2016 14:10:23 +0800 Shawn Guo wrote:
On Tue, Mar 08, 2016 at 09:04:03AM +0100, Lothar Waßmann wrote:quoted
Add support for the following i.MX6 based modules from Ka-Ro electronics GmbH: TX6S-8034: Processor Freescale i.MX 6 Solo, 800MHz RAM 256MiB DDR3 SDRAM ROM 128MiB NAND Flash Power supply Single 3.1V to 5.5V Size 31mm SO-DIMM Temp. Range industrial grade (-40°C/-25°C to 105°C Tj) TX6S-8035: Processor Freescale i.MX 6 Solo, 800MHz RAM 512MiB DDR3 SDRAM ROM 4GiB eMMC Power supply Single 3.1V to 5.5V Size 31mm SO-DIMM Temp. Range industrial grade (-40°C/-25°C to 105°C Tj) TX6U-8033: Processor Freescale i.MX 6 Dual Lite, 800MHz RAM 1GiB DDR3 SDRAM ROM 4GiB eMMC Power supply Single 3.1V to 5.5V Size 31mm SO-DIMM Temp. Range industrial grade (-40°C/-25°C to 105°C Tj) TX6Q-1036: Processor Freescale i.MX 6Quad, 1GHz RAM 1GB DDR3 SDRAM 64-bit ROM 8GiB eMMC Power supply Single 3.1V to 5.5V Size 31mm SO-DIMM Temp. Range Extended Consumer Grade (-20°C to 105°C Tj) Signed-off-by: Lothar Waßmann <redacted> --- arch/arm/boot/dts/Makefile | 4 + arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 249 ++++++++++++++++++++++++++++ arch/arm/boot/dts/imx6dl-tx6s-8035.dts | 246 +++++++++++++++++++++++++++ arch/arm/boot/dts/imx6dl-tx6u-8033.dts | 248 +++++++++++++++++++++++++++ arch/arm/boot/dts/imx6q-tx6q-1036.dts | 295 +++++++++++++++++++++++++++++++++ 5 files changed, 1042 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8035.dts create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-8033.dts create mode 100644 arch/arm/boot/dts/imx6q-tx6q-1036.dtsdiff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 072294f..71b5cd3 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile@@ -320,6 +320,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-sabrelite.dtb \ imx6dl-sabresd.dtb \ imx6dl-tx6dl-comtft.dtb \ + imx6dl-tx6s-8034.dtb \ + imx6dl-tx6s-8035.dtb \ + imx6dl-tx6u-8033.dtb \imx6dl-tx6u-8033.dtb should go after imx6dl-tx6u-801x.dtb?
Of course. I obviously missed this when dropping the patch to rename the dtb files which you rejected. NB: There is no need to quote the full original mail when you have no further comments on the remaining part. This would save people from having to scroll through the mail needlessly looking for further comments. Lothar Waßmann