[PATCH resend v2 7/9] ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators
From: Chen-Yu Tsai <hidden>
Date: 2016-03-29 09:31:00
Also in:
linux-arm-kernel, lkml
Subsystem:
the rest · Maintainer:
Linus Torvalds
The AXP809 PMIC is the primary PMIC. It provides various supply voltages for the SoC and other peripherals. The PMIC's interrupt line is connected to NMI pin of the SoC. Signed-off-by: Chen-Yu Tsai <redacted> --- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 131 +++++++++++++++++++++++++++- 1 file changed, 129 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index eb2ccd0a3bd5..8d8af1189d87 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts@@ -98,7 +98,7 @@ &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; bus-width = <4>; cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */ cd-inverted;
@@ -108,7 +108,7 @@ &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_pins>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; bus-width = <8>; non-removable; cap-mmc-hw-reset;
@@ -126,8 +126,135 @@ &r_rsb { status = "okay"; + + axp809: pmic@3a3 { + reg = <0x3a3>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + + regulators { + reg_aldo1: aldo1 { + /* + * TODO: This should be handled by the + * USB PHY driver. + */ + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc33-usbh"; + }; + + reg_aldo2: aldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pb-io-cam"; + }; + + aldo3 { + /* unused */ + }; + + reg_dc5ldo: dc5ldo { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus-09-usbh"; + }; + + reg_dcdc1: dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v"; + }; + + reg_dcdc2: dcdc2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; + }; + + reg_dcdc3: dcdc3 { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; + }; + + reg_dcdc4: dcdc4 { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-sys-usb0-hdmi"; + }; + + reg_dcdc5: dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1425000>; + regulator-max-microvolt = <1575000>; + regulator-name = "vcc-dram"; + }; + + reg_dldo1: dldo1 { + /* + * The WiFi chip supports a wide range + * (3.0 ~ 4.8V) of voltages, and so does + * this regulator (3.0 ~ 4.2V), but + * Allwinner SDK always sets it to 3.3V. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; + }; + + reg_dldo2: dldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-pl"; + }; + + reg_eldo1: eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dvdd-cam"; + }; + + reg_eldo2: eldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pe"; + }; + + reg_eldo3: eldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-pm-codec-io1"; + }; + + reg_ldo_io0: ldo_io0 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-pg"; + }; + + reg_ldo_io1: ldo_io1 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-pa-gmac-2v5"; + }; + + reg_rtc_ldo: rtc_ldo { + regulator-name = "vcc-rtc-vdd1v8-io"; + }; + }; + }; }; +#include "axp809.dtsi" + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>;
--
2.7.0