@@ -0,0 +1,19 @@
+* Universal Flash Storage (UFS) DesignWare Host Controller
+
+DWC_UFSHC nodes are defined to describe on-chip UFS host controllers.
+Each UFS controller instance should have its own node.
+
+Required properties:
+- compatible        : compatible list must contain "snps,ufshcd-dwc" and should
+		      also contain the JEDEC version of the controller:
+			"jedec,ufs-1.1"
+			"jedec,ufs-2.0"
+- reg               : <registers mapping>
+- interrupts        : <interrupt mapping for UFS host controller IRQ>
+
+Example:
+	ufs@0xd0000000 {
+		compatible = "jedec,ufs-2.0", "snps,dwc-ufshcd";
+		reg = < 0xd0000000 0x10000 >;
+		interrupts = < 24 >;
+	};

@@ -11006,6 +11006,12 @@ S:	Supported
 F:	Documentation/scsi/ufs.txt
 F:	drivers/scsi/ufs/
 
+UNIVERSAL FLASH STORAGE HOST CONTROLLER DRIVER DWC HOOKS
+M:	Joao Pinto <Joao.Pinto@synopsys.com>
+L:	linux-scsi@vger.kernel.org
+S:	Supported
+F:	drivers/scsi/ufs/*dwc*
+
 UNSORTED BLOCK IMAGES (UBI)
 M:	Artem Bityutskiy <dedekind1@gmail.com>
 M:	Richard Weinberger <richard@nod.at>

@@ -83,3 +83,54 @@ config SCSI_UFS_QCOM
 
 	  Select this if you have UFS controller on QCOM chipset.
 	  If unsure, say N.
+
+config SCSI_UFS_DWC_HOOKS
+	bool
+
+config SCSI_UFS_DWC_PLAT
+	tristate "DesignWare UFS controller platform glue driver"
+	depends on SCSI_UFSHCD_PLATFORM
+	select SCSI_UFS_DWC_HOOKS
+	help
+	  This selects the DesignWare UFS host controller platform glue driver.
+
+	  Select this if you have a DesignWare UFS controller on Platform bus.
+	  If unsure, say N.
+
+config SCSI_UFS_DWC_PCI
+	tristate "DesignWare UFS controller pci glue driver"
+	depends on SCSI_UFSHCD_PCI
+	select SCSI_UFS_DWC_HOOKS
+	help
+	  This selects the DesignWare UFS host controller pci glue driver.
+
+	  Select this if you have a DesignWare UFS controller on pci bus.
+	  If unsure, say N.
+
+config SCSI_UFS_DWC_TC
+	bool "Support for the Synopsys Test Chip"
+	depends on SCSI_UFS_DWC_HOOKS && (SCSI_UFSHCD_PCI || SCSI_UFS_DWC_PLAT)
+	---help---
+	  Synopsys Test Chip is a Phy for prototyping purposes.
+	  This selects the support for the Synopsys Test Chip.
+
+	  Select this if you have a Synopsys Test Chip.
+	  If unsure, say N.
+
+config SCSI_UFS_DWC_20BIT_RMMI
+	bool "20-bit RMMI support"
+	depends on SCSI_UFS_DWC_TC
+	---help---
+	  This specifies that the Synopsys Test Chip supports 20-bit RMMI.
+
+	  Select this if you are using a 20-bit RMMI Synopsys Test Chip.
+	  If unsure, say N.
+
+config SCSI_UFS_DWC_40BIT_RMMI
+	bool "40-bit RMMI support"
+	depends on SCSI_UFS_DWC_TC
+	---help---
+	  Synopsys Test Chip is a Phy for prototyping purposes.
+
+	  Select this if you are using a 40-bit RMMI Synopsys Test Chip.
+	  If unsure, say N.

@@ -1,4 +1,7 @@
 # UFSHCD makefile
+obj-$(CONFIG_SCSI_UFS_DWC_HOOKS) += ufshcd-dwc.o
+obj-$(CONFIG_SCSI_UFS_DWC_PLAT) += ufs-dwc.o
+obj-$(CONFIG_SCSI_UFS_DWC_PCI) += ufs-dwc-pci.o
 obj-$(CONFIG_SCSI_UFS_QCOM) += ufs-qcom.o
 obj-$(CONFIG_SCSI_UFSHCD) += ufshcd.o
 obj-$(CONFIG_SCSI_UFSHCD_PCI) += ufshcd-pci.o

@@ -0,0 +1,172 @@
+/*
+ * UFS Host driver for Synopsys Designware Core
+ *
+ * Copyright (C) 2015-2016 Synopsys, Inc. (www.synopsys.com)
+ *
+ * Authors: Joao Pinto <jpinto@synopsys.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "ufshcd.h"
+#include "ufshcd-dwc.h"
+
+#include <linux/pci.h>
+#include <linux/pm_runtime.h>
+
+/**
+ * ufs_dw_pci_suspend - suspend power management function
+ * @pdev: pointer to PCI device handle
+ * @state: power state
+ *
+ * Returns 0 if successful
+ * Returns non-zero otherwise
+ */
+static int ufs_dw_pci_suspend(struct device *dev)
+{
+	return ufshcd_system_suspend(dev_get_drvdata(dev));
+}
+
+/**
+ * ufs_dw_pci_resume - resume power management function
+ * @pdev: pointer to PCI device handle
+ *
+ * Returns 0 if successful
+ * Returns non-zero otherwise
+ */
+static int ufs_dw_pci_resume(struct device *dev)
+{
+	return ufshcd_system_resume(dev_get_drvdata(dev));
+}
+
+static int ufs_dw_pci_runtime_suspend(struct device *dev)
+{
+	return ufshcd_runtime_suspend(dev_get_drvdata(dev));
+}
+static int ufs_dw_pci_runtime_resume(struct device *dev)
+{
+	return ufshcd_runtime_resume(dev_get_drvdata(dev));
+}
+static int ufs_dw_pci_runtime_idle(struct device *dev)
+{
+	return ufshcd_runtime_idle(dev_get_drvdata(dev));
+}
+
+/**
+ * struct ufs_hba_dwc_vops - UFS DWC specific variant operations
+ */
+static struct ufs_hba_variant_ops ufs_dwc_pci_hba_vops = {
+	.name                   = "ufshcd-dwc-pci",
+	.link_startup_notify	= ufshcd_dwc_link_startup_notify,
+};
+
+/**
+ * ufs_dw_pci_shutdown - main function to put the controller in reset state
+ * @pdev: pointer to PCI device handle
+ */
+static void ufs_dw_pci_shutdown(struct pci_dev *pdev)
+{
+	ufshcd_shutdown((struct ufs_hba *)pci_get_drvdata(pdev));
+}
+
+/**
+ * ufs_dw_pci_remove - de-allocate PCI/SCSI host and host memory space
+ *		data structure memory
+ * @pdev - pointer to PCI handle
+ */
+static void ufs_dw_pci_remove(struct pci_dev *pdev)
+{
+	struct ufs_hba *hba = pci_get_drvdata(pdev);
+
+	pm_runtime_forbid(&pdev->dev);
+	pm_runtime_get_noresume(&pdev->dev);
+	ufshcd_remove(hba);
+}
+
+/**
+ * ufs_dw_pci_probe - probe routine of the driver
+ * @pdev: pointer to PCI device handle
+ * @id: PCI device id
+ *
+ * Returns 0 on success, non-zero value on failure
+ */
+static int
+ufs_dw_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	struct ufs_hba *hba;
+	void __iomem *mmio_base;
+	int err;
+
+	err = pcim_enable_device(pdev);
+	if (err) {
+		dev_err(&pdev->dev, "pcim_enable_device failed\n");
+		return err;
+	}
+
+	pci_set_master(pdev);
+
+	err = pcim_iomap_regions(pdev, 1 << 0, UFSHCD);
+	if (err < 0) {
+		dev_err(&pdev->dev, "request and iomap failed\n");
+		return err;
+	}
+
+	mmio_base = pcim_iomap_table(pdev)[0];
+
+	err = ufshcd_alloc_host(&pdev->dev, &hba);
+	if (err) {
+		dev_err(&pdev->dev, "Allocation failed\n");
+		return err;
+	}
+
+	INIT_LIST_HEAD(&hba->clk_list_head);
+
+	hba->vops = &ufs_dwc_pci_hba_vops;
+
+	err = ufshcd_init(hba, mmio_base, pdev->irq);
+	if (err) {
+		dev_err(&pdev->dev, "Initialization failed\n");
+		return err;
+	}
+
+	pci_set_drvdata(pdev, hba);
+	pm_runtime_put_noidle(&pdev->dev);
+	pm_runtime_allow(&pdev->dev);
+
+	return 0;
+}
+
+static const struct dev_pm_ops ufs_dw_pci_pm_ops = {
+	.suspend	= ufs_dw_pci_suspend,
+	.resume		= ufs_dw_pci_resume,
+	.runtime_suspend = ufs_dw_pci_runtime_suspend,
+	.runtime_resume  = ufs_dw_pci_runtime_resume,
+	.runtime_idle    = ufs_dw_pci_runtime_idle,
+};
+
+static const struct pci_device_id ufs_dw_pci_tbl[] = {
+	{ PCI_VENDOR_ID_SYNOPSYS, 0xB101, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+	{ PCI_VENDOR_ID_SYNOPSYS, 0xB102, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+	{ }	/* terminate list */
+};
+
+MODULE_DEVICE_TABLE(pci, ufs_dw_pci_tbl);
+
+static struct pci_driver ufs_dw_pci_driver = {
+	.name = UFSHCD,
+	.id_table = ufs_dw_pci_tbl,
+	.probe = ufs_dw_pci_probe,
+	.remove = ufs_dw_pci_remove,
+	.shutdown = ufs_dw_pci_shutdown,
+	.driver = {
+		.pm = &ufs_dw_pci_pm_ops
+	},
+};
+
+module_pci_driver(ufs_dw_pci_driver);
+
+MODULE_AUTHOR("Joao Pinto <Joao.Pinto@synopsys.com>");
+MODULE_DESCRIPTION("DesignWare UFS host controller PCI glue driver");
+MODULE_LICENSE("Dual BSD/GPL");

@@ -0,0 +1,96 @@
+/*
+ * UFS Host driver for Synopsys Designware Core
+ *
+ * Copyright (C) 2015-2016 Synopsys, Inc. (www.synopsys.com)
+ *
+ * Authors: Joao Pinto <jpinto@synopsys.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/delay.h>
+
+#include "ufshcd-pltfrm.h"
+#include "ufshcd-dwc.h"
+
+/**
+ * struct ufs_hba_dwc_vops - UFS DWC specific variant operations
+ *
+ */
+static struct ufs_hba_variant_ops ufs_dwc_hba_vops = {
+	.name                   = "ufshcd-dwc",
+	.link_startup_notify	= ufshcd_dwc_link_startup_notify,
+};
+
+/**
+ * ufs_dwc_probe()
+ * @pdev: pointer to platform device structure
+ *
+ */
+static int ufs_dwc_probe(struct platform_device *pdev)
+{
+	int err;
+	struct device *dev = &pdev->dev;
+
+	/* Perform generic probe */
+	err = ufshcd_pltfrm_init(pdev, &ufs_dwc_hba_vops);
+	if (err)
+		dev_err(dev, "ufshcd_pltfrm_init() failed %d\n", err);
+
+	return err;
+}
+
+/**
+ * ufs_dwc_remove()
+ * @pdev: pointer to platform device structure
+ *
+ */
+static int ufs_dwc_remove(struct platform_device *pdev)
+{
+	struct ufs_hba *hba =  platform_get_drvdata(pdev);
+
+	pm_runtime_get_sync(&(pdev)->dev);
+	ufshcd_remove(hba);
+
+	return 0;
+}
+
+static const struct of_device_id ufs_dwc_match[] = {
+	{
+		.compatible = "snps,ufshcd-dwc"
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, ufs_dwc_match);
+
+static const struct dev_pm_ops ufs_dwc_pm_ops = {
+	.suspend	= ufshcd_pltfrm_suspend,
+	.resume		= ufshcd_pltfrm_resume,
+	.runtime_suspend = ufshcd_pltfrm_runtime_suspend,
+	.runtime_resume  = ufshcd_pltfrm_runtime_resume,
+	.runtime_idle    = ufshcd_pltfrm_runtime_idle,
+};
+
+static struct platform_driver ufs_dwc_driver = {
+	.probe		= ufs_dwc_probe,
+	.remove		= ufs_dwc_remove,
+	.shutdown = ufshcd_pltfrm_shutdown,
+	.driver		= {
+		.name	= "ufshcd-dwc",
+		.pm	= &ufs_dwc_pm_ops,
+		.of_match_table	= of_match_ptr(ufs_dwc_match),
+	},
+};
+
+module_platform_driver(ufs_dwc_driver);
+
+MODULE_ALIAS("platform:ufshcd-dwc");
+MODULE_DESCRIPTION("DesignWare UFS Host platform glue driver");
+MODULE_AUTHOR("Joao Pinto <Joao.Pinto@synopsys.com>");
+MODULE_LICENSE("Dual BSD/GPL");

@@ -0,0 +1,431 @@
+/*
+ * UFS Host driver for Synopsys Designware Core
+ *
+ * Copyright (C) 2015-2016 Synopsys, Inc. (www.synopsys.com)
+ *
+ * Authors: Joao Pinto <jpinto@synopsys.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "ufshcd.h"
+#include "unipro.h"
+
+#include "ufshcd-dwc.h"
+#include "ufshci-dwc.h"
+
+struct ufshcd_dme_attr_val {
+	u32 attr_sel;
+	u32 mib_val;
+	u8 peer;
+};
+
+int ufshcd_dme_set_attrs(struct ufs_hba *hba,
+				const struct ufshcd_dme_attr_val *v, int n)
+{
+	int ret = 0;
+	int attr_node = 0;
+
+	for (attr_node = 0; attr_node < n; attr_node++) {
+		ret = ufshcd_dme_set_attr(hba, v[attr_node].attr_sel,
+			ATTR_SET_NOR, v[attr_node].mib_val, v[attr_node].peer);
+
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * ufshcd_dwc_program_clk_div()
+ * This function programs the clk divider value. This value is needed to
+ * provide 1 microsecond tick to unipro layer.
+ * @hba: Private Structure pointer
+ * @divider_val: clock divider value to be programmed
+ *
+ */
+static void ufshcd_dwc_program_clk_div(struct ufs_hba *hba, u32 divider_val)
+{
+	ufshcd_writel(hba, divider_val, DWC_UFS_REG_HCLKDIV);
+}
+
+/**
+ * ufshcd_dwc_link_is_up()
+ * Check if link is up
+ * @hba: private structure poitner
+ *
+ * Returns 0 on success, non-zero value on failure
+ */
+static int ufshcd_dwc_link_is_up(struct ufs_hba *hba)
+{
+	int dme_result = 0;
+
+	ufshcd_dme_get(hba, UIC_ARG_MIB(VS_POWERSTATE), &dme_result);
+
+	if (dme_result == UFSHCD_LINK_IS_UP) {
+		ufshcd_set_link_active(hba);
+		return 0;
+	}
+
+	return 1;
+}
+
+/**
+ * ufshcd_dwc_connection_setup()
+ * This function configures both the local side (host) and the peer side
+ * (device) unipro attributes to establish the connection to application/
+ * cport.
+ * This function is not required if the hardware is properly configured to
+ * have this connection setup on reset. But invoking this function does no
+ * harm and should be fine even working with any ufs device.
+ *
+ * @hba: pointer to drivers private data
+ *
+ * Returns 0 on success non-zero value on failure
+ */
+static int ufshcd_dwc_connection_setup(struct ufs_hba *hba)
+{
+	const struct ufshcd_dme_attr_val setup_attrs[] = {
+		{ UIC_ARG_MIB(T_CONNECTIONSTATE), 0, DME_LOCAL },
+		{ UIC_ARG_MIB(N_DEVICEID), 0, DME_LOCAL },
+		{ UIC_ARG_MIB(N_DEVICEID_VALID), 0, DME_LOCAL },
+		{ UIC_ARG_MIB(T_PEERDEVICEID), 1, DME_LOCAL },
+		{ UIC_ARG_MIB(T_PEERCPORTID), 0, DME_LOCAL },
+		{ UIC_ARG_MIB(T_TRAFFICCLASS), 0, DME_LOCAL },
+		{ UIC_ARG_MIB(T_CPORTFLAGS), 0x6, DME_LOCAL },
+		{ UIC_ARG_MIB(T_CPORTMODE), 1, DME_LOCAL },
+		{ UIC_ARG_MIB(T_CONNECTIONSTATE), 1, DME_LOCAL },
+		{ UIC_ARG_MIB(T_CONNECTIONSTATE), 0, DME_PEER },
+		{ UIC_ARG_MIB(N_DEVICEID), 1, DME_PEER },
+		{ UIC_ARG_MIB(N_DEVICEID_VALID), 1, DME_PEER },
+		{ UIC_ARG_MIB(T_PEERDEVICEID), 1, DME_PEER },
+		{ UIC_ARG_MIB(T_PEERCPORTID), 0, DME_PEER },
+		{ UIC_ARG_MIB(T_TRAFFICCLASS), 0, DME_PEER },
+		{ UIC_ARG_MIB(T_CPORTFLAGS), 0x6, DME_PEER },
+		{ UIC_ARG_MIB(T_CPORTMODE), 1, DME_PEER },
+		{ UIC_ARG_MIB(T_CONNECTIONSTATE), 1, DME_PEER }
+	};
+
+	return ufshcd_dme_set_attrs(hba, setup_attrs, ARRAY_SIZE(setup_attrs));
+}
+
+#ifdef CONFIG_SCSI_UFS_DWC_40BIT_RMMI
+/**
+ * ufshcd_dwc_setup_40bit_rmmi()
+ * This function configures Synopsys TC specific atributes (40-bit RMMI)
+ * @hba: Pointer to drivers structure
+ *
+ * Returns 0 on success or non-zero value on failure
+ */
+static int ufshcd_dwc_setup_40bit_rmmi(struct ufs_hba *hba)
+{
+	const struct ufshcd_dme_attr_val setup_attrs[] = {
+		{ UIC_ARG_MIB(TX_GLOBALHIBERNATE), 0x00, DME_LOCAL },
+		{ UIC_ARG_MIB(REFCLKMODE), 0x01, DME_LOCAL },
+		{ UIC_ARG_MIB(CDIRECTCTRL6), 0x80, DME_LOCAL },
+		{ UIC_ARG_MIB(CBDIVFACTOR), 0x08, DME_LOCAL },
+		{ UIC_ARG_MIB(CBDCOCTRL5), 0x64, DME_LOCAL },
+		{ UIC_ARG_MIB(CBPRGTUNING), 0x09, DME_LOCAL },
+		{ UIC_ARG_MIB(RTOBSERVESELECT), 0x00, DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(TX_REFCLKFREQ, SELIND_LN0_TX), 0x01,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(TX_CFGCLKFREQVAL, SELIND_LN0_TX), 0x19,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGEXTRATTR, SELIND_LN0_TX), 0x14,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(DITHERCTRL2, SELIND_LN0_TX), 0xd6,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RX_REFCLKFREQ, SELIND_LN0_RX), 0x01,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RX_CFGCLKFREQVAL, SELIND_LN0_RX), 0x19,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGWIDEINLN, SELIND_LN0_RX), 4,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXCDR8, SELIND_LN0_RX), 0x80,
+								DME_LOCAL },
+		{ UIC_ARG_MIB(DIRECTCTRL10), 0x04, DME_LOCAL },
+		{ UIC_ARG_MIB(DIRECTCTRL19), 0x02, DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXCDR8, SELIND_LN0_RX), 0x80,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(ENARXDIRECTCFG4, SELIND_LN0_RX), 0x03,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXOVR8, SELIND_LN0_RX), 0x16,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RXDIRECTCTRL2, SELIND_LN0_RX), 0x42,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(ENARXDIRECTCFG3, SELIND_LN0_RX), 0xa4,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RXCALCTRL, SELIND_LN0_RX), 0x01,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(ENARXDIRECTCFG2, SELIND_LN0_RX), 0x01,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXOVR4, SELIND_LN0_RX), 0x28,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RXSQCTRL, SELIND_LN0_RX), 0x1E,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXOVR6, SELIND_LN0_RX), 0x2f,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXOVR6, SELIND_LN0_RX), 0x2f,
+								DME_LOCAL },
+		{ UIC_ARG_MIB(CBPRGPLL2), 0x00, DME_LOCAL },
+	};
+
+	return ufshcd_dme_set_attrs(hba, setup_attrs, ARRAY_SIZE(setup_attrs));
+}
+
+#endif
+
+#ifdef CONFIG_SCSI_UFS_DWC_20BIT_RMMI
+/**
+ * ufshcd_dwc_setup_20bit_rmmi_lane0()
+ * This function configures Synopsys TC 20-bit RMMI Lane 0
+ * @hba: Pointer to drivers structure
+ *
+ * Returns 0 on success or non-zero value on failure
+ */
+static int ufshcd_dwc_setup_20bit_rmmi_lane0(struct ufs_hba *hba)
+{
+	const struct ufshcd_dme_attr_val setup_attrs[] = {
+		{ UIC_ARG_MIB_SEL(TX_REFCLKFREQ, SELIND_LN0_TX), 0x01,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(TX_CFGCLKFREQVAL, SELIND_LN0_TX), 0x19,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RX_CFGCLKFREQVAL, SELIND_LN0_RX), 0x19,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGEXTRATTR, SELIND_LN0_TX), 0x12,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(DITHERCTRL2, SELIND_LN0_TX), 0xd6,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RX_REFCLKFREQ, SELIND_LN0_RX), 0x01,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGWIDEINLN, SELIND_LN0_RX), 2,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXCDR8, SELIND_LN0_RX), 0x80,
+								DME_LOCAL },
+		{ UIC_ARG_MIB(DIRECTCTRL10), 0x04, DME_LOCAL },
+		{ UIC_ARG_MIB(DIRECTCTRL19), 0x02, DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(ENARXDIRECTCFG4, SELIND_LN0_RX), 0x03,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXOVR8, SELIND_LN0_RX), 0x16,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RXDIRECTCTRL2, SELIND_LN0_RX), 0x42,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(ENARXDIRECTCFG3, SELIND_LN0_RX), 0xa4,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RXCALCTRL, SELIND_LN0_RX), 0x01,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(ENARXDIRECTCFG2, SELIND_LN0_RX), 0x01,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXOVR4, SELIND_LN0_RX), 0x28,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RXSQCTRL, SELIND_LN0_RX), 0x1E,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXOVR6, SELIND_LN0_RX), 0x2f,
+								DME_LOCAL },
+		{ UIC_ARG_MIB(CBPRGPLL2), 0x00, DME_LOCAL },
+	};
+
+	return ufshcd_dme_set_attrs(hba, setup_attrs, ARRAY_SIZE(setup_attrs));
+}
+
+/**
+ * ufshcd_dwc_setup_20bit_rmmi_lane1()
+ * This function configures Synopsys TC 20-bit RMMI Lane 1
+ * @hba: Pointer to drivers structure
+ *
+ * Returns 0 on success or non-zero value on failure
+ */
+static int ufshcd_dwc_setup_20bit_rmmi_lane1(struct ufs_hba *hba)
+{
+	int connected_rx_lanes = 0;
+	int connected_tx_lanes = 0;
+	int ret = 0;
+
+	const struct ufshcd_dme_attr_val setup_tx_attrs[] = {
+		{ UIC_ARG_MIB_SEL(TX_REFCLKFREQ, SELIND_LN1_TX), 0x0d,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(TX_CFGCLKFREQVAL, SELIND_LN1_TX), 0x19,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGEXTRATTR, SELIND_LN1_TX), 0x12,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(DITHERCTRL2, SELIND_LN0_TX), 0xd6,
+								DME_LOCAL },
+	};
+
+	const struct ufshcd_dme_attr_val setup_rx_attrs[] = {
+		{ UIC_ARG_MIB_SEL(RX_REFCLKFREQ, SELIND_LN1_RX), 0x01,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RX_CFGCLKFREQVAL, SELIND_LN1_RX), 0x19,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGWIDEINLN, SELIND_LN1_RX), 2,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXCDR8, SELIND_LN1_RX), 0x80,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(ENARXDIRECTCFG4, SELIND_LN1_RX), 0x03,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXOVR8, SELIND_LN1_RX), 0x16,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RXDIRECTCTRL2, SELIND_LN1_RX), 0x42,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(ENARXDIRECTCFG3, SELIND_LN1_RX), 0xa4,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RXCALCTRL, SELIND_LN1_RX), 0x01,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(ENARXDIRECTCFG2, SELIND_LN1_RX), 0x01,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXOVR4, SELIND_LN1_RX), 0x28,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(RXSQCTRL, SELIND_LN1_RX), 0x1E,
+								DME_LOCAL },
+		{ UIC_ARG_MIB_SEL(CFGRXOVR6, SELIND_LN1_RX), 0x2f,
+								DME_LOCAL },
+	};
+
+	/* Get the available lane count */
+	ufshcd_dme_get(hba, UIC_ARG_MIB(PA_CONNECTEDRXDATALANES),
+			&connected_rx_lanes);
+	ufshcd_dme_get(hba, UIC_ARG_MIB(PA_CONNECTEDTXDATALANES),
+			&connected_tx_lanes);
+
+	if (connected_tx_lanes == 2) {
+
+		ret = ufshcd_dme_set_attrs(hba, setup_tx_attrs,
+						ARRAY_SIZE(setup_tx_attrs));
+
+		if (ret)
+			goto out;
+	}
+
+	if (connected_rx_lanes == 2) {
+		ret = ufshcd_dme_set_attrs(hba, setup_rx_attrs,
+						ARRAY_SIZE(setup_rx_attrs));
+	}
+
+out:
+	return ret;
+}
+
+/**
+ * ufshcd_dwc_setup_20bit_rmmi()
+ * This function configures Synopsys TC specific atributes (20-bit RMMI)
+ * @hba: Pointer to drivers structure
+ *
+ * Returns 0 on success or non-zero value on failure
+ */
+static int ufshcd_dwc_setup_20bit_rmmi(struct ufs_hba *hba)
+{
+	int ret = 0;
+
+	const struct ufshcd_dme_attr_val setup_attrs[] = {
+		{ UIC_ARG_MIB(TX_GLOBALHIBERNATE), 0x00, DME_LOCAL },
+		{ UIC_ARG_MIB(REFCLKMODE), 0x01, DME_LOCAL },
+		{ UIC_ARG_MIB(CDIRECTCTRL6), 0xc0, DME_LOCAL },
+		{ UIC_ARG_MIB(CBDIVFACTOR), 0x44, DME_LOCAL },
+		{ UIC_ARG_MIB(CBDCOCTRL5), 0x64, DME_LOCAL },
+		{ UIC_ARG_MIB(CBPRGTUNING), 0x09, DME_LOCAL },
+		{ UIC_ARG_MIB(RTOBSERVESELECT), 0x00, DME_LOCAL },
+	};
+
+	ret = ufshcd_dme_set_attrs(hba, setup_attrs, ARRAY_SIZE(setup_attrs));
+	if (ret)
+		goto out;
+
+	/* Lane 0 configuration*/
+	ret = ufshcd_dwc_setup_20bit_rmmi_lane0(hba);
+	if (ret)
+		goto out;
+
+	/* Lane 1 configuration*/
+	ret = ufshcd_dwc_setup_20bit_rmmi_lane1(hba);
+	if (ret)
+		goto out;
+
+out:
+	return ret;
+}
+#endif
+
+/**
+ * ufshcd_dwc_setup_tc()
+ * This function configures Local (host) Synopsys TC specific attributes
+ *
+ * @hba: Pointer to drivers structure
+ *
+ * Returns 0 on success non-zero value on failure
+ */
+static int ufshcd_dwc_setup_tc(struct ufs_hba *hba)
+{
+	int ret = 0;
+
+#ifdef CONFIG_SCSI_UFS_DWC_40BIT_RMMI
+	dev_info(hba->dev, "Configuring Test Chip 40-bit RMMI\n");
+	ret = ufshcd_dwc_setup_40bit_rmmi(hba);
+	if (ret) {
+		dev_err(hba->dev, "Configuration failed\n");
+		goto out;
+	}
+#endif
+
+#ifdef CONFIG_SCSI_UFS_DWC_20BIT_RMMI
+	dev_info(hba->dev, "Configuring Test Chip 20-bit RMMI\n");
+	ret = ufshcd_dwc_setup_20bit_rmmi(hba);
+	if (ret) {
+		dev_err(hba->dev, "Configuration failed\n");
+		goto out;
+	}
+#endif
+	/* To write Shadow register bank to effective configuration block */
+	ret = ufshcd_dme_set(hba, UIC_ARG_MIB(VS_MPHYCFGUPDT), 0x01);
+	if (ret)
+		goto out;
+
+	/* To configure Debug OMC */
+	ret = ufshcd_dme_set(hba, UIC_ARG_MIB(VS_DEBUGOMC), 0x01);
+
+out:
+	return ret;
+}
+
+/**
+ * ufshcd_dwc_link_startup_notify()
+ * UFS Host DWC specific link startup sequence
+ * @hba: private structure poitner
+ * @status: Callback notify status
+ *
+ * Returns 0 on success, non-zero value on failure
+ */
+int ufshcd_dwc_link_startup_notify(struct ufs_hba *hba,
+					enum ufs_notify_change_status status)
+{
+	int err = 0;
+
+	if (status == PRE_CHANGE) {
+		ufshcd_dwc_program_clk_div(hba, DWC_UFS_REG_HCLKDIV_DIV_125);
+#ifdef CONFIG_SCSI_UFS_DWC_TC
+		err = ufshcd_dwc_setup_tc(hba);
+		if (err) {
+			dev_err(hba->dev, "Configuration failed (%d)\n",
+									err);
+			goto out;
+		}
+#endif
+	} else { /* POST_CHANGE */
+		err = ufshcd_dwc_link_is_up(hba);
+		if (err) {
+			dev_err(hba->dev, "Link is not up\n");
+			goto out;
+		}
+
+		err = ufshcd_dwc_connection_setup(hba);
+		if (err)
+			dev_err(hba->dev, "Connection setup failed (%d)\n",
+									err);
+	}
+
+out:
+	return err;
+}
+EXPORT_SYMBOL(ufshcd_dwc_link_startup_notify);

@@ -0,0 +1,18 @@
+/*
+ * UFS Host driver for Synopsys Designware Core
+ *
+ * Copyright (C) 2015-2016 Synopsys, Inc. (www.synopsys.com)
+ *
+ * Authors: Joao Pinto <jpinto@synopsys.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _UFSHCD_DWC_H
+#define _UFSHCD_DWC_H
+
+int ufshcd_dwc_link_startup_notify(struct ufs_hba *hba,
+					enum ufs_notify_change_status status);
+#endif /* End of Header */

@@ -0,0 +1,42 @@
+/*
+ * UFS Host driver for Synopsys Designware Core
+ *
+ * Copyright (C) 2015-2016 Synopsys, Inc. (www.synopsys.com)
+ *
+ * Authors: Joao Pinto <jpinto@synopsys.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _UFSHCI_DWC_H
+#define _UFSHCI_DWC_H
+
+/* DWC HC UFSHCI specific Registers */
+enum dwc_specific_registers {
+	DWC_UFS_REG_HCLKDIV	= 0xFC,
+};
+
+/* Link Status*/
+enum link_status {
+	UFSHCD_LINK_IS_DOWN	= 1,
+	UFSHCD_LINK_IS_UP	= 2,
+};
+
+/* Clock Divider Values: Hex equivalent of frequency in MHz */
+enum clk_div_values {
+	DWC_UFS_REG_HCLKDIV_DIV_62_5	= 0x3e,
+	DWC_UFS_REG_HCLKDIV_DIV_125	= 0x7d,
+	DWC_UFS_REG_HCLKDIV_DIV_200	= 0xc8,
+};
+
+/* Selector Index */
+enum selector_index {
+	SELIND_LN0_TX		= 0x00,
+	SELIND_LN1_TX		= 0x01,
+	SELIND_LN0_RX		= 0x04,
+	SELIND_LN1_RX		= 0x05,
+};
+
+#endif /* End of Header */

@@ -35,6 +35,10 @@
 #define TX_LCC_SEQUENCER			0x0032
 #define TX_MIN_ACTIVATETIME			0x0033
 #define TX_PWM_G6_G7_SYNC_LENGTH		0x0034
+#define TX_REFCLKFREQ				0x00EB
+#define TX_CFGCLKFREQVAL			0x00EC
+#define	CFGEXTRATTR				0x00F0
+#define DITHERCTRL2				0x00F1
 
 /*
  * M-RX Configuration Attributes

@@ -48,8 +52,38 @@
 #define RX_ENTER_HIBERN8			0x00A7
 #define RX_BYPASS_8B10B_ENABLE			0x00A8
 #define RX_TERMINATION_FORCE_ENABLE		0x0089
+#define RX_REFCLKFREQ				0x00EB
+#define	RX_CFGCLKFREQVAL			0x00EC
+#define CFGWIDEINLN				0x00F0
+#define CFGRXCDR8				0x00BA
+#define ENARXDIRECTCFG4				0x00F2
+#define CFGRXOVR8				0x00BD
+#define RXDIRECTCTRL2				0x00C7
+#define ENARXDIRECTCFG3				0x00F3
+#define RXCALCTRL				0x00B4
+#define ENARXDIRECTCFG2				0x00F4
+#define CFGRXOVR4				0x00E9
+#define RXSQCTRL				0x00B5
+#define CFGRXOVR6				0x00BF
 
 #define is_mphy_tx_attr(attr)			(attr < RX_MODE)
+
+/*
+ * Common Block Attributes
+ */
+#define TX_GLOBALHIBERNATE			UNIPRO_CB_OFFSET(0x002B)
+#define REFCLKMODE				UNIPRO_CB_OFFSET(0x00BF)
+#define DIRECTCTRL19				UNIPRO_CB_OFFSET(0x00CD)
+#define DIRECTCTRL10				UNIPRO_CB_OFFSET(0x00E6)
+#define CDIRECTCTRL6				UNIPRO_CB_OFFSET(0x00EA)
+#define RTOBSERVESELECT				UNIPRO_CB_OFFSET(0x00F0)
+#define CBDIVFACTOR				UNIPRO_CB_OFFSET(0x00F1)
+#define CBDCOCTRL5				UNIPRO_CB_OFFSET(0x00F3)
+#define CBPRGPLL2				UNIPRO_CB_OFFSET(0x00F8)
+#define CBPRGTUNING				UNIPRO_CB_OFFSET(0x00FB)
+
+#define UNIPRO_CB_OFFSET(x)			(0x8000 | x)
+
 /*
  * PHY Adpater attributes
  */

@@ -110,6 +144,11 @@
 #define PA_STALLNOCONFIGTIME	0x15A3
 #define PA_SAVECONFIGTIME	0x15A4
 
+/*Other attributes*/
+#define VS_MPHYCFGUPDT		0xD085
+#define VS_DEBUGOMC		0xD09E
+#define VS_POWERSTATE		0xD083
+
 /* PA power modes */
 enum {
 	FAST_MODE	= 1,