[PATCH v5 01/14] dt/bindings: Add bindings for PIC32 interrupt controller
From: Joshua Henderson <hidden>
Date: 2016-01-14 01:15:33
Also in:
linux-mips, lkml
Subsystem:
irqchip drivers, open firmware and flattened device tree bindings, the rest · Maintainers:
Thomas Gleixner, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds
From: Cristian Birsan <cristian.birsan@microchip.com> Document the devicetree bindings for the interrupt controller on Microchip PIC32 class devices. Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com> Signed-off-by: Joshua Henderson <redacted> Cc: Ralf Baechle <redacted> --- Changes since v4: - Add new microchip,external-interrupts property - Provide a better description of some of the features - Clean up formatting Changes since v3: None Changes since v2: None Changes since v1: - Remove hardware interrupt priorities from interrupt controller DT bindings. --- .../interrupt-controller/microchip,pic32-evic.txt | 67 ++++++++++++++++++++ 1 file changed, 67 insertions(+) create mode 100644 Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt
diff --git a/Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt b/Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt
new file mode 100644
index 0000000..c3a1b37
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt@@ -0,0 +1,67 @@ +Microchip PIC32 Interrupt Controller +==================================== + +The Microchip PIC32 contains an Enhanced Vectored Interrupt Controller (EVIC). +It handles all internal and external interrupts. This controller exists outside +of the CPU and is the arbitrator of all interrupts (including interrupts from +the CPU itself) before they are presented to the CPU. + +External interrupts have a software configurable edge polarity. Non external +interrupts have a type and polarity that is determined by the source of the +interrupt. + +Required properties +------------------- + +- compatible: Should be "microchip,pic32mzda-evic" +- reg: Specifies physical base address and size of register range. +- interrupt-controller: Identifies the node as an interrupt controller. +- #interrupt cells: Specifies the number of cells used to encode an interrupt + source connected to this controller. The value shall be 2 and interrupt + descriptor shall have the following format: + + <hw_irq irq_type> + + hw_irq - represents the hardware interrupt number as in the data sheet. + irq_type - is used to describe the type and polarity of an interrupt. For + internal interrupts use IRQ_TYPE_EDGE_RISING for non persistent interrupts and + IRQ_TYPE_LEVEL_HIGH for persistent interrupts. For external interrupts use + IRQ_TYPE_EDGE_RISING or IRQ_TYPE_EDGE_FALLING to select the desired polarity. + +Optional properties +------------------- +- microchip,external-irqs: u32 array of external interrupts with software + polarity configuration. This array corresponds to the bits in the INTCON + SFR. + +Example +------- + +evic: interrupt-controller@1f810000 { + compatible = "microchip,pic32mzda-evic"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x1f810000 0x1000>; + microchip,external-irqs = <3 8 13 18 23>; +}; + +Each device/peripheral must request its interrupt line with the associated type +and polarity. + +Internal interrupt DTS snippet +------------------------------ + +device@1f800000 { + ... + interrupts = <113 IRQ_TYPE_LEVEL_HIGH>; + ... +}; + +External interrupt DTS snippet +------------------------------ + +device@1f800000 { + ... + interrupts = <3 IRQ_TYPE_EDGE_RISING>; + ... +};
--
1.7.9.5