Hi Chunyan,

Minor but important fixes below.

And for the v9 version, please only use "To:" for
"Greg Kroah-Hartman [off-list ref]"

All other recipients should only be Cc:

Regards,
Peter Hurley


On 01/27/2015 02:56 AM, Chunyan Zhang wrote:

Add a full sc9836-uart driver for SC9836 SoC which is based on the
spreadtrum sharkl64 platform.
This driver also support earlycon.

[...]

+static int sprd_probe_dt_alias(int index, struct device *dev)
+{
+	struct device_node *np;
+	static bool seen_dev_with_alias;
+	static bool seen_dev_without_alias;

        ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

delete these two lines; these were used for the message deleted in a
previous patch version.

+	int ret = index;
+
+	if (!IS_ENABLED(CONFIG_OF))
+		return ret;
+
+	np = dev->of_node;
+	if (!np)
+		return ret;
+
+	ret = of_alias_get_id(np, "serial");
+	if (IS_ERR_VALUE(ret)) {
+		seen_dev_without_alias = true;

                ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
delete this line.

+		ret = index;
+	} else {
+		seen_dev_with_alias = true;

                ^^^^^^^^^^^^^^^^^^^^^^^^^^^
delete this line.

+		if (ret >= ARRAY_SIZE(sprd_port) || sprd_port[ret] != NULL) {
+			dev_warn(dev, "requested serial port %d  not available.\n", ret);
+			ret = index;
+		}
+	}

Simplify the entire "if (IS_ERR_VALUE(ret))" statement to:

	if (IS_ERR_VALUE(ret))
		ret = index;
	else if (ret >= ..................) {
		dev_warn(.....);
		ret = index;
	}

+
+	return ret;
+}
+
+static int sprd_remove(struct platform_device *dev)
+{
+	struct sprd_uart_port *sup = platform_get_drvdata(dev);
+
+	if (sup) {
+		uart_remove_one_port(&sprd_uart_driver, &sup->port);
+		sprd_port[sup->port.line] = NULL;
+		sprd_ports_num--;
+	}
+
+	if (!sprd_ports_num)
+		uart_unregister_driver(&sprd_uart_driver);
+
+	return 0;
+}
+
+static int sprd_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct uart_port *up;
+	struct clk *clk;
+	int irq;
+	int index;
+	int ret;
+
+	for (index = 0; index < ARRAY_SIZE(sprd_port); index++)
+		if (sprd_port[index] == NULL)
+			break;
+
+	if (index == ARRAY_SIZE(sprd_port))
+		return -EBUSY;
+
+	index = sprd_probe_dt_alias(index, &pdev->dev);
+
+	sprd_port[index] = devm_kzalloc(&pdev->dev,
+		sizeof(*sprd_port[index]), GFP_KERNEL);
+	if (!sprd_port[index])
+		return -ENOMEM;
+
+	pdev->id = index;

        ^^^^^^^^^^^^^^^^
delete this line.

The platform device id cannot be assigned by the driver.
(This was left over from trying to fix sprd_suspend/sprd_resume
but that's fixed correctly now.)

+
+	up = &sprd_port[index]->port;
+	up->dev = &pdev->dev;
+	up->line = index;
+	up->type = PORT_SPRD;
+	up->iotype = SERIAL_IO_PORT;
+	up->uartclk = SPRD_DEF_RATE;
+	up->fifosize = SPRD_FIFO_SIZE;
+	up->ops = &serial_sprd_ops;
+	up->flags = UPF_BOOT_AUTOCONF;
+
+	clk = devm_clk_get(&pdev->dev, NULL);
+	if (!IS_ERR(clk))
+		up->uartclk = clk_get_rate(clk);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "not provide mem resource\n");
+		return -ENODEV;
+	}
+	up->mapbase = res->start;
+	up->membase = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(up->membase))
+		return PTR_ERR(up->membase);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "not provide irq resource\n");
+		return -ENODEV;
+	}
+	up->irq = irq;
+
+	if (!sprd_ports_num) {
+		ret = uart_register_driver(&sprd_uart_driver);
+		if (ret < 0) {
+			pr_err("Failed to register SPRD-UART driver\n");
+			return ret;
+		}
+	}
+	sprd_ports_num++;
+
+	ret = uart_add_one_port(&sprd_uart_driver, up);
+	if (ret) {
+		sprd_port[index] = NULL;
+		sprd_remove(pdev);
+	}
+
+	platform_set_drvdata(pdev, up);
+
+	return ret;
+}