Hi Hans,

On 16/01/2015 09:17, Hans de Goede wrote:

Hi,

On 15-01-15 15:09, Gregory CLEMENT wrote:

quoted

Add the regulators to each SATA port.

Signed-off-by: Gregory CLEMENT <redacted>
---
  arch/arm/boot/dts/armada-388-gp.dts | 126 ++++++++++++++++++++++++++++++++++++
  1 file changed, 126 insertions(+)

diff --git a/arch/arm/boot/dts/armada-388-gp.dts b/arch/arm/boot/dts/armada-388-gp.dts
index 4df22bf91683..590b383db323 100644
--- a/arch/arm/boot/dts/armada-388-gp.dts
+++ b/arch/arm/boot/dts/armada-388-gp.dts

@@ -173,6 +173,16 @@
  				status = "okay";
  				#address-cells = <1>;
  				#size-cells = <0>;
+
+				sata0: sata-port@0 {
+					reg = <0>;
+					target-supply = <&reg_5v_sata0>;
+				};
+
+				sata1: sata-port@1 {
+					reg = <1>;
+					target-supply = <&reg_5v_sata1>;
+				};
  			};

  			sata@e0000 {

@@ -181,6 +191,16 @@
  				status = "okay";
  				#address-cells = <1>;
  				#size-cells = <0>;
+
+				sata2: sata-port@0 {
+					reg = <0>;
+					target-supply = <&reg_5v_sata2>;
+				};
+
+				sata3: sata-port@1 {
+					reg = <1>;
+					target-supply = <&reg_5v_sata3>;
+				};
  			};

  			sdhci@d8000 {

@@ -278,6 +298,112 @@
  		regulator-always-on;
  		gpio = <&expander0 4 GPIO_ACTIVE_HIGH>;
  	};
+
+	reg_sata0: pwr-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "pwr_en_sata0";
+		enable-active-high;
+		regulator-always-on;
+
+	};
+
+	reg_5v_sata0: v5-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata0>;
+	};
+
+	reg_12v_sata0: v12-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata0>;
+	};

AFAIK the separate v5 / 12v regulators you're creating here
are not used anywhere. So I guess there just here to
accurately / completely describe the power topology ?

Yes it was the point.

quoted

+
+	reg_sata1: pwr-sata1 {
+		regulator-name = "pwr_en_sata1";
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		enable-active-high;
+		regulator-always-on;

The always on here seems to a bit weird, wasn't the
whole purpose of this patch set to teach ahci_platform
to turn it on as needed ?

Maybe I misunderstood the regulator binding, but I thought
that (once the suspend will be available on this platform) I
could use:

regulator-state-mem {
			regulator-off-in-suspend;
		};

You do probably want to put a regulator-boot-on here so
that disks do not get an unwanted powercycle (bad for
their lifetime) when the firmware has already turned on
the disk. Downside of using regulator-boot-on is that if
the power is not actually turned on no power-on-delay is

That's why I didn't use it

done, but we're not using a power on delay anyways.

But if regulator-always-on prevent to switch it off in
suspend then yes using regulator-boot-on is better.

Thanks,

Gregory

The same goes for reg_sata2 & reg_sata3.

quoted

+		gpio = <&expander0 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_5v_sata1: v5-sata1 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata1";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata1>;
+	};
+
+	reg_12v_sata1: v12-sata1 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata1";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata1>;
+	};
+
+	reg_sata2: pwr-sata2 {
+		compatible = "regulator-fixed";
+		regulator-name = "pwr_en_sata2";
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_5v_sata2: v5-sata2 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata2";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata2>;
+	};
+
+	reg_12v_sata2: v12-sata2 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata2";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata2>;
+	};
+
+	reg_sata3: pwr-sata3 {
+		compatible = "regulator-fixed";
+		regulator-name = "pwr_en_sata3";
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_5v_sata3: v5-sata3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata3";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata3>;
+	};
+
+	reg_12v_sata3: v12-sata3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata3";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata3>;
+	};
  };

  &pinctrl {

Regards,

Hans

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com