Re: [PATCH v2 1/2] ASoC: Add support for CS35L32 Boosted Amplifier

On Sat, 2 Aug 2014, Dinh Nguyen wrote:

On 8/1/14, 9:45 AM, Brian Austin wrote:

quoted

This patch adds support for the Cirrus Logic CS35L32 Boosted Amplifier
I2S output provides monitor data to the SOC/CODEC/DSP for speaker protection algorithms

Changes for v2:
- Interrupt Status registers added to regmap volatile
- Use Speaker for volume control name
- Zero Cross Switch rename
- Remove Gain Manager from DTS and add to kcontrols
- Add VP-Supply to regulator list
- Remove uneeded DAPM event
- Specify MCLK rates as numbers
- Move probe/remove code to device level probe/remove
- Move regmap_register_patch to after REV_ID check

Signed-off-by: Brian Austin <redacted>
---

quoted

+static int cs35l32_handle_of_data(struct i2c_client *i2c_client,
+				    struct cs35l32_platform_data *pdata)
+{
+	struct device_node *np = i2c_client->dev.of_node;
+	unsigned int val;
+
+	if (of_property_read_u32(np, "cirrus,sdout-share", &val) >= 0)
+		pdata->sdout_share = val;
+
+	of_property_read_u32(np, "cirrus,boost-manager", &val);
+	switch (val) {
+	case CS35L32_BOOST_MGR_AUTO:
+	case CS35L32_BOOST_MGR_AUTO_AUDIO:
+	case CS35L32_BOOST_MGR_BYPASS:
+	case CS35L32_BOOST_MGR_FIXED:
+		pdata->boost_mng = val;
+		break;
+	default:
+		dev_err(&i2c_client->dev,
+			"Wrong cirrus,boost-manager DT value %d\n", val);
+		pdata->boost_mng = CS35L32_BOOST_MGR_BYPASS;
+	}
+
+	of_property_read_u32(np, "cirrus,sdout-datacfg", &val);
+	switch (val) {
+	case CS35L32_DATA_CFG_LR_VP:
+	case CS35L32_DATA_CFG_LR_STAT:
+	case CS35L32_DATA_CFG_LR:
+	case CS35L32_DATA_CFG_LR_VPSTAT:
+		pdata->sdout_datacfg = val;
+		break;
+	default:
+		dev_err(&i2c_client->dev,
+			"Wrong cirrus,sdout-datacfg DT value %d\n", val);
+		pdata->sdout_datacfg = CS35L32_DATA_CFG_LR;
+	}
+
+	of_property_read_u32(np, "cirrus,battery-threshold", &val);
+	switch (val) {
+	case CS35L32_BATT_THRESH_3_1V:
+	case CS35L32_BATT_THRESH_3_2V:
+	case CS35L32_BATT_THRESH_3_3V:
+	case CS35L32_BATT_THRESH_3_4V:
+		pdata->batt_thresh = val;
+		break;
+	default:
+		dev_err(&i2c_client->dev,
+			"Wrong cirrus,battery-threshold DT value %d\n", val);
+		pdata->batt_thresh = CS35L32_BATT_THRESH_3_3V;
+	}
+
+	of_property_read_u32(np, "cirrus,battery-recovery", &val);
+	switch (val) {
+	case CS35L32_BATT_RECOV_3_1V:
+	case CS35L32_BATT_RECOV_3_2V:
+	case CS35L32_BATT_RECOV_3_3V:
+	case CS35L32_BATT_RECOV_3_4V:
+	case CS35L32_BATT_RECOV_3_5V:
+	case CS35L32_BATT_RECOV_3_6V:
+		pdata->batt_recov = val;
+		break;
+	default:
+		dev_err(&i2c_client->dev,
+			"Wrong cirrus,battery-recovery DT value %d\n", val);
+		pdata->batt_recov = CS35L32_BATT_RECOV_3_4V;
+	}
+
+	return 0;
+}
+
+static int cs35l32_i2c_probe(struct i2c_client *i2c_client,
+				       const struct i2c_device_id *id)
+{
+	struct cs35l32_private *cs35l32;
+	struct cs35l32_platform_data *pdata =
+		dev_get_platdata(&i2c_client->dev);
+	int ret, i;
+	unsigned int devid = 0;
+	unsigned int reg;
+
+
+	cs35l32 = devm_kzalloc(&i2c_client->dev, sizeof(struct cs35l32_private),
+			       GFP_KERNEL);
+	if (!cs35l32) {
+		dev_err(&i2c_client->dev, "could not allocate codec\n");
+		return -ENOMEM;
+	}
+
+	i2c_set_clientdata(i2c_client, cs35l32);
+
+	cs35l32->regmap = devm_regmap_init_i2c(i2c_client, &cs35l32_regmap);
+	if (IS_ERR(cs35l32->regmap)) {
+		ret = PTR_ERR(cs35l32->regmap);
+		dev_err(&i2c_client->dev, "regmap_init() failed: %d\n", ret);
+		return ret;
+	}
+
+	if (pdata) {
+		cs35l32->pdata = *pdata;
+	} else {
+		pdata = devm_kzalloc(&i2c_client->dev,
+				     sizeof(struct cs35l32_platform_data),
+				GFP_KERNEL);
+		if (!pdata) {
+			dev_err(&i2c_client->dev, "could not allocate pdata\n");
+			return -ENOMEM;
+		}
+		if (i2c_client->dev.of_node) {
+			ret = cs35l32_handle_of_data(i2c_client,
+						     &cs35l32->pdata);
+			if (ret != 0)
+				return ret;

Doesn't cs35l32_handle_of_data() always return 0?

I thought about this and I think I am going to keep this check incase I 
change anything about handle_of_data and would like to check the return 
value. I don't think it causes anything bad to keep it. I always like to  
have this check just in case.

 > > +		}

quoted

+	}
+
+	for (i = 0; i < ARRAY_SIZE(cs35l32->supplies); i++)
+		cs35l32->supplies[i].supply = cs35l32_supply_names[i];
+
+	ret = devm_regulator_bulk_get(&i2c_client->dev,
+				      ARRAY_SIZE(cs35l32->supplies),
+				      cs35l32->supplies);
+	if (ret != 0) {
+		dev_err(&i2c_client->dev,
+			"Failed to request supplies: %d\n", ret);
+		return ret;
+	}
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(cs35l32->supplies),
+				    cs35l32->supplies);
+	if (ret != 0) {
+		dev_err(&i2c_client->dev,
+			"Failed to enable supplies: %d\n", ret);
+		return ret;
+	}
+
+	/* Reset the Device */
+	cs35l32->reset_gpio = devm_gpiod_get(&i2c_client->dev,
+		"reset-gpios");
+	if (IS_ERR(cs35l32->reset_gpio)) {
+		ret = PTR_ERR(cs35l32->reset_gpio);
+		if (ret != -ENOENT && ret != -ENOSYS)
+			return ret;
+
+		cs35l32->reset_gpio = NULL;
+	} else {
+		ret = gpiod_direction_output(cs35l32->reset_gpio, 0);
+		if (ret)
+			return ret;
+		gpiod_set_value_cansleep(cs35l32->reset_gpio, 1);
+	}
+
+	/* initialize codec */
+	ret = regmap_read(cs35l32->regmap, CS35L32_DEVID_AB, &reg);
+	devid = (reg & 0xFF) << 12;
+
+	ret = regmap_read(cs35l32->regmap, CS35L32_DEVID_CD, &reg);
+	devid |= (reg & 0xFF) << 4;
+
+	ret = regmap_read(cs35l32->regmap, CS35L32_DEVID_E, &reg);
+	devid |= (reg & 0xF0) >> 4;
+
+	if (devid != CS35L32_CHIP_ID) {
+		ret = -ENODEV;
+		dev_err(&i2c_client->dev,
+			"CS35L32 Device ID (%X). Expected %X\n",
+			devid, CS35L32_CHIP_ID);
+		return ret;
+	}
+
+	ret = regmap_read(cs35l32->regmap, CS35L32_REV_ID, &reg);
+	if (ret < 0) {
+		dev_err(&i2c_client->dev, "Get Revision ID failed\n");
+		return ret;
+	}
+
+	ret = regmap_register_patch(cs35l32->regmap, cs35l32_monitor_patch,
+				    ARRAY_SIZE(cs35l32_monitor_patch));
+	if (ret < 0) {
+		dev_err(&i2c_client->dev, "Failed to apply errata patch\n");
+		return ret;
+	}
+
+	dev_info(&i2c_client->dev,
+		 "Cirrus Logic CS35L32, Revision: %02X\n", reg & 0xFF);
+
+	/* Setup VBOOST Management */
+	if (cs35l32->pdata.boost_mng)
+		regmap_update_bits(cs35l32->regmap, CS35L32_AUDIO_LED_MNGR,
+				   CS35L32_BOOST_MASK,
+				cs35l32->pdata.boost_mng);
+
+	/* Setup ADSP Format Config */
+	if (cs35l32->pdata.sdout_share)
+		regmap_update_bits(cs35l32->regmap, CS35L32_ADSP_CTL,
+				    CS35L32_ADSP_SHARE_MASK,
+				cs35l32->pdata.sdout_share << 3);
+
+	/* Setup ADSP Data Configuration */
+	if (cs35l32->pdata.sdout_datacfg)
+		regmap_update_bits(cs35l32->regmap, CS35L32_ADSP_CTL,
+				   CS35L32_ADSP_DATACFG_MASK,
+				cs35l32->pdata.sdout_datacfg << 4);
+
+	/* Setup Low Battery Recovery  */
+	if (cs35l32->pdata.batt_recov)
+		regmap_update_bits(cs35l32->regmap, CS35L32_BATT_THRESHOLD,
+				   CS35L32_BATT_REC_MASK,
+				cs35l32->pdata.batt_recov << 1);
+
+	/* Setup Low Battery Threshold */
+	if (cs35l32->pdata.batt_thresh)
+		regmap_update_bits(cs35l32->regmap, CS35L32_BATT_THRESHOLD,
+				   CS35L32_BATT_THRESH_MASK,
+				cs35l32->pdata.batt_thresh << 4);
+
+	/* Power down the AMP */
+	regmap_update_bits(cs35l32->regmap, CS35L32_PWRCTL1, CS35L32_PDN_AMP,
+			    CS35L32_PDN_AMP);
+
+	/* Clear MCLK Error Bit since we don't have the clock yet */
+	ret = regmap_read(cs35l32->regmap, CS35L32_INT_STATUS_1, &reg);
+
+	ret =  snd_soc_register_codec(&i2c_client->dev,
+			&soc_codec_dev_cs35l32, cs35l32_dai,
+			ARRAY_SIZE(cs35l32_dai));
+
+	if (ret < 0)
+		return ret;
+	return 0;

Should be able to just "return ret" here.

I will change this but related to the regulator in case 
snd_soc_register_codec fails.

Thanks,
Brian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html