Re: [PATCH v2 4/4] brcmfmac: Fix OOB interrupt not working for BCM43362
From: Arend van Spriel <hidden>
Date: 2014-06-17 11:49:46
Also in:
linux-arm-kernel, linux-wireless
On 16-06-14 19:56, Hans de Goede wrote:
It has taken me a long long time to get the OOB interrupt working on the AP6210 sdio wifi/bt module found on various Allwinner A20 boards. In the end I found these magic register pokes in the cubietruck kernel tree: https://github.com/cubieboard2/linux-sunxi/commit/7f08ba395617d17e7a711507503d89a50406fe7a I'm not entirely sure if this specific to the AP6210 module, or if this should be done for all BCM43362 sdio devices.
Hi Hans, I was still not sure about this one so I asked around. Apart from the nvram settings I emailed earlier one more is needed: sd_gpout=1 sd_oobonly=1 sd_gpval=1 *muxenab=0x11* Could you give that a try? Regards, Arend
quoted hunk
Signed-off-by: Hans de Goede <redacted> --- drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)diff --git a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c index 0fc707c..58e86a5 100644 --- a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c +++ b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c@@ -39,7 +39,9 @@ #include <brcm_hw_ids.h> #include <brcmu_utils.h> #include <brcmu_wifi.h> +#include <chipcommon.h> #include <soc.h> +#include "chip.h" #include "dhd_bus.h" #include "dhd_dbg.h" #include "sdio_host.h"@@ -119,6 +121,7 @@ int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev) { int ret = 0; u8 data; + u32 addr, gpiocontrol; unsigned long flags; if ((sdiodev->pdata) && (sdiodev->pdata->oob_irq_supported)) {@@ -148,6 +151,19 @@ int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev) sdio_claim_host(sdiodev->func[1]); + if (sdiodev->bus_if->chip == BCM43362_CHIP_ID) { + /* assign GPIO to SDIO core */ + addr = CORE_CC_REG(SI_ENUM_BASE, gpiocontrol); + gpiocontrol = brcmf_sdiod_regrl(sdiodev, addr, &ret); + gpiocontrol |= 0x2; + brcmf_sdiod_regwl(sdiodev, addr, gpiocontrol, &ret); + + brcmf_sdiod_regwb(sdiodev, SBSDIO_GPIO_SELECT, 0xf, + &ret); + brcmf_sdiod_regwb(sdiodev, SBSDIO_GPIO_OUT, 0, &ret); + brcmf_sdiod_regwb(sdiodev, SBSDIO_GPIO_EN, 0x2, &ret); + } + /* must configure SDIO_CCCR_IENx to enable irq */ data = brcmf_sdiod_regrb(sdiodev, SDIO_CCCR_IENx, &ret); data |= 1 << SDIO_FUNC_1 | 1 << SDIO_FUNC_2 | 1;