Re: [PATCH 3/3] ARM: dts: kirkwood: add kirkwood-km_fixedeth DTS file
From: Sebastian Hesselbarth <hidden>
Date: 2014-05-15 10:43:16
Also in:
linux-arm-kernel
On 05/15/2014 11:48 AM, Valentin Longchamp wrote:
Besides our Kirkwood Reference design, there is another group of board on which the eth interface is not connected to a phy but to a swtich for
s/swtich/switch/
some board internal communication. The configuration of the switch is handled by an EEPROM or by the bootloader, but on the kirkwood side, the port is always configured as 1000 Mbits, full duplex.
Hmm, if it is another variant of the Keymile board we already have,
it should probably go like this:
+ kirkwood.dtsi
+ kirkwood-98dx4122.dtsi
+--> kirkwood_km_common.dtsi
+--> kirkwood_km_kirkwood.dts
+--> kirkwood_km_fixedeth.dts
Andrew did some great series for the various NAS vendor boards, where
you can look at.
quoted hunk
Signed-off-by: Valentin Longchamp <redacted> --- arch/arm/boot/dts/kirkwood-km_fixedeth.dts | 70 ++++++++++++++++++++++++++++++ 1 file changed, 70 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-km_fixedeth.dtsdiff --git a/arch/arm/boot/dts/kirkwood-km_fixedeth.dts b/arch/arm/boot/dts/kirkwood-km_fixedeth.dts new file mode 100644 index 0000000..3d54d9b --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-km_fixedeth.dts@@ -0,0 +1,70 @@ +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-98dx4122.dtsi" + +/ { + model = "Keymile Kirkwood Fixed Eth"; + compatible = "keymile,km_fixedeth", "marvell,kirkwood-98DX4122", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x08000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + stdout-path = &uart0; + }; + + mbus { + pcie-controller { + status = "okay"; + + pcie@1,0 { + status = "okay"; + }; + }; + }; + + ocp@f1000000 { + pinctrl: pin-controller@10000 { + pinctrl-0 = < &pmx_i2c_gpio_sda &pmx_i2c_gpio_scl >; + pinctrl-names = "default"; + + pmx_i2c_gpio_sda: pmx-gpio-sda { + marvell,pins = "mpp8"; + marvell,function = "gpio"; + }; + pmx_i2c_gpio_scl: pmx-gpio-scl { + marvell,pins = "mpp9"; + marvell,function = "gpio"; + }; + }; + + serial@12000 { + status = "ok"; + }; + }; + + i2c@0 { + compatible = "i2c-gpio"; + gpios = < &gpio0 8 GPIO_ACTIVE_HIGH /* sda */ + &gpio0 9 GPIO_ACTIVE_HIGH>; /* scl */ + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + }; +}; + +&nand { + status = "okay"; + chip-delay = <25>; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <>;
Is that empty phy-handle required? If so, we should probably fix it in mv643xx_eth instead.
+ speed = <1000>; /* <SPEED_1000> */ + duplex = <0x01>; /* <DUPLEX_FULL> */
s/0x01/1/ Sebastian
+ }; +};
-- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html