Re: [PATCH] tty/serial: change of_serial to use new of_property_read_u32() api
From: Rob Herring <hidden>
Date: 2011-06-30 20:57:28
Also in:
linux-serial, lkml
Grant, On 06/30/2011 02:00 PM, Grant Likely wrote:
Simplifies the code a bit and drops a few lines. Signed-off-by: Grant Likely <redacted> --- I've only actually build tested this, but this shows some of the cleanup achieved using the of_property_read_u32() API. If this gets merged in the v3.1 merge window then it will need to go via the devicetree/next branch. g.
You can't give yourself bonus points. ;)
quoted hunk ↗ jump to hunk
drivers/tty/serial/of_serial.c | 37 +++++++++++++++---------------------- 1 files changed, 15 insertions(+), 22 deletions(-)diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c index 36038ed..dbfbfda 100644 --- a/drivers/tty/serial/of_serial.c +++ b/drivers/tty/serial/of_serial.c@@ -32,17 +32,17 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev, { struct resource resource; struct device_node *np = ofdev->dev.of_node; - const __be32 *clk, *spd; - const __be32 *prop; - int ret, prop_size; + u32 clk, spd, prop; + int ret; memset(port, 0, sizeof *port); - spd = of_get_property(np, "current-speed", NULL); - clk = of_get_property(np, "clock-frequency", NULL); - if (!clk) { + if (of_property_read_u32(np, "clock-frequency", &clk)) {
s/clk/port->uartclk/ And below, then remove clk.
quoted hunk ↗ jump to hunk
dev_warn(&ofdev->dev, "no clock-frequency property set\n"); return -ENODEV; } + /* If current-speed was set, then try not to change it. */ + if (of_property_read_u32(np, "current-speed", &spd) == 0) + port->custom_divisor = clk / (16 * spd); ret = of_address_to_resource(np, 0, &resource); if (ret) {@@ -54,20 +54,17 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev, port->mapbase = resource.start; /* Check for shifted address mapping */ - prop = of_get_property(np, "reg-offset", &prop_size); - if (prop && (prop_size == sizeof(u32))) - port->mapbase += be32_to_cpup(prop); + if (of_property_read_u32(np, "reg-offset", &prop) == 0) + port->mapbase += prop; /* Check for registers offset within the devices address range */ - prop = of_get_property(np, "reg-shift", &prop_size); - if (prop && (prop_size == sizeof(u32))) - port->regshift = be32_to_cpup(prop); + if (of_property_read_u32(np, "reg-shift", &prop) == 0) + port->regshift = prop;
Can be further simplified: of_property_read_u32(np, "reg-shift", &port->regshift); Rob
quoted hunk ↗ jump to hunk
port->irq = irq_of_parse_and_map(np, 0); port->iotype = UPIO_MEM; - prop = of_get_property(np, "reg-io-width", &prop_size); - if (prop && (prop_size == sizeof(u32))) { - switch (be32_to_cpup(prop)) { + if (of_property_read_u32(np, "reg-io-width", &prop) == 0) { + switch (prop) { case 1: port->iotype = UPIO_MEM; break;@@ -75,21 +72,17 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev, port->iotype = UPIO_MEM32; break; default: - dev_warn(&ofdev->dev, - "unsupported io width (%d bytes)\n", - be32_to_cpup(prop)); + dev_warn(&ofdev->dev, "unsupported reg-io-width (%d)\n", + prop); return -EINVAL; } } port->type = type; - port->uartclk = be32_to_cpup(clk); + port->uartclk = clk; port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP | UPF_FIXED_PORT | UPF_FIXED_TYPE; port->dev = &ofdev->dev; - /* If current-speed was set, then try not to change it. */ - if (spd) - port->custom_divisor = be32_to_cpup(clk) / (16 * (be32_to_cpup(spd))); return 0; }_______________________________________________ devicetree-discuss mailing list devicetree-discuss@lists.ozlabs.org https://lists.ozlabs.org/listinfo/devicetree-discuss