Re: [PATCH V4 4/5] net/fec: check id_entry pointer before using it
From: Grant Likely <hidden>
Date: 2011-03-15 07:09:04
On Thu, Mar 10, 2011 at 12:59:44PM +0800, Jason Liu wrote:
The id_entry will possibly be NULL, So, need check id_entry and make sure it not NULL before using it. Signed-off-by: Jason Liu <redacted> Signed-off-by: Jason Liu <redacted>
Other than the double s-o-b lines, this patch looks good to me. Acked-by: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org> g.
quoted hunk
--- drivers/net/fec.c | 12 ++++++------ 1 files changed, 6 insertions(+), 6 deletions(-)diff --git a/drivers/net/fec.c b/drivers/net/fec.c index 2a71373..02cdd71 100644 --- a/drivers/net/fec.c +++ b/drivers/net/fec.c@@ -293,7 +293,7 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev) * the system that it's running on. As the result, driver has to * swap every frame going to and coming from the controller. */ - if (id_entry->driver_data & FEC_QUIRK_SWAP_FRAME) + if (id_entry && id_entry->driver_data & FEC_QUIRK_SWAP_FRAME) swap_buffer(bufaddr, skb->len); /* Save skb pointer */@@ -529,7 +529,7 @@ fec_enet_rx(struct net_device *dev) dma_unmap_single(NULL, bdp->cbd_bufaddr, bdp->cbd_datlen, DMA_FROM_DEVICE); - if (id_entry->driver_data & FEC_QUIRK_SWAP_FRAME) + if (id_entry && id_entry->driver_data & FEC_QUIRK_SWAP_FRAME) swap_buffer(data, pkt_len); /* This does 16 byte alignment, exactly what we need.@@ -808,7 +808,7 @@ static int fec_enet_mii_init(struct platform_device *pdev) * mdio interface in board design, and need to be configured by * fec0 mii_bus. */ - if ((id_entry->driver_data & FEC_QUIRK_ENET_MAC) && pdev->id) { + if (id_entry && (id_entry->driver_data & FEC_QUIRK_ENET_MAC) && pdev->id) { /* fec1 uses fec0 mii_bus */ fep->mii_bus = fec0_mii_bus; return 0;@@ -851,7 +851,7 @@ static int fec_enet_mii_init(struct platform_device *pdev) goto err_out_free_mdio_irq; /* save fec0 mii_bus */ - if (id_entry->driver_data & FEC_QUIRK_ENET_MAC) + if (id_entry && id_entry->driver_data & FEC_QUIRK_ENET_MAC) fec0_mii_bus = fep->mii_bus; return 0;@@ -1238,7 +1238,7 @@ fec_restart(struct net_device *dev, int duplex) * enet-mac reset will reset mac address registers too, * so need to reconfigure it. */ - if (id_entry->driver_data & FEC_QUIRK_ENET_MAC) { + if (id_entry && id_entry->driver_data & FEC_QUIRK_ENET_MAC) { memcpy(&temp_mac, dev->dev_addr, ETH_ALEN); writel(cpu_to_be32(temp_mac[0]), fep->hwp + FEC_ADDR_LOW); writel(cpu_to_be32(temp_mac[1]), fep->hwp + FEC_ADDR_HIGH);@@ -1294,7 +1294,7 @@ fec_restart(struct net_device *dev, int duplex) * The phy interface and speed need to get configured * differently on enet-mac. */ - if (id_entry->driver_data & FEC_QUIRK_ENET_MAC) { + if (id_entry && id_entry->driver_data & FEC_QUIRK_ENET_MAC) { val = readl(fep->hwp + FEC_R_CNTRL); /* MII or RMII */-- 1.7.1