On 20.05.21 г. 9:11, Naohiro Aota wrote:

I have a few questions about btrfs_io_geometry()'s behavior. 

While I'm testing zoned btrfs on ZNS drive with 2GB zone size, I hit
the following ASSERT in btrfs_submit_direct() by running fstests
btrfs/017.

static blk_qc_t btrfs_submit_direct(struct inode *inode, struct iomap *iomap,
		struct bio *dio_bio, loff_t file_offset)
{
...
	start_sector = dio_bio->bi_iter.bi_sector;
	submit_len = dio_bio->bi_iter.bi_size;

	do {
		logical = start_sector << 9;
		em = btrfs_get_chunk_map(fs_info, logical, submit_len);
...
		ret = btrfs_get_io_geometry(fs_info, em, btrfs_op(dio_bio),
					    logical, submit_len, &geom);
...
		ASSERT(geom.len <= INT_MAX);

		clone_len = min_t(int, submit_len, geom.len);
...
		bio = btrfs_bio_clone_partial(dio_bio, clone_offset, clone_len);


On zoned btrfs, we create a SINGLE block group whose size is equal to
the device zone size, so we have a 2 GB SINGLE block group on a 2 GB
zone size drive. Then, on a SINGLE single block group,
btrfs_io_geometry() returns the remaining length from @logical to the
end of the block group regardless of the @len argument. Thus, with
@logical == 0, we get geom->len = 2 GB, which is larger than INT_MAX,
hitting the ASSERT.

I'm confusing because I'm not sure what the ASSERT wants to do. It
might want to guard btrfs_bio_clone_partial() (and bio_trim()) below?
But, since bio_trim() takes sector-based values, and the passed
"clone_offset" and "clone_len" is byte-based, we can technically allow
larger bytes than INT_MAX. (well, we might never build such large bio,
though). And, it looks meaningless to check geom->len here. Since, it
can be much larger than bio size on a SINGLE block group.

So, in summary, below are my questions.

1. About btrfs_bio_clone_partial()
  1.1 What is the meaning of geom->len?
      - Length from @logical to the stripe boundary? or
      - Length [logical, logical+len] can go without crossing the boundary?

So think of it as splitting a block group into 64k chunks (those are the
stripes) then finding in which such 64k chunk/stripe_nr logical falls
within, so len would be the length of an io you could do without
crossing this 64k boundary. This process is described in
https://github.com/btrfs/btrfs-dev-docs/blob/master/bio-submission.txt
under section 'Bio mapping'. With this in mind I'd say it's  [logical,
logical+len] without crossing a 64k boundary. !!!HOWEVER!!!!  This
applies to bg types other than SINGLE , that's the
if (map->type & BTRFS_BLOCK_GROUP_PROFILE_MASK) check in the function.
We do this because for raid levels we'd like the io granularity to be
64k, whereas for SINGLE we simply issue a single write, i.e len is
calculated as:

len = em->len - offset;

which is why you are getting such the size of the block group.

  1.2 @len is currently unused in btrfs_bio_clone_partial(), is this correct?

It's used to calculate @clone_len parameter so it's indirectly involved
in btrfs_bio_clone_partial.

  1.3 What should we fill into geom->len when the block group is SINGLE profile?

See above.

2. About the ASSERT
  2.1 Shouldn't we check submit_len (= bio's length) instead of geom->len ?

The assert got added quite a while back so I'm not entirely sure it's
pertinent.

  2.2 Can't it be larger than INT_MAX? e.g., INT_MAX << SECTOR_SHIFT?

3. About btrfs_bio_clone_partial()
  3.1 We can change "int" to "u64" maybe?

Can we though? So if size in btrfs_bio_clone_partial is switched to u64
then in that fuction we do size >> 9 potentially having a value of at
most 55 bits, passing it to bio_trim, which in turn takes an int. So
you'd be truncating values at the time you call bio_trim, no ?