[PATCH V5 7/7] arm64: dts: imx95: Move power supply properties to Root Port node

From: Sherry Sun (OSS) <hidden>
Date: 2026-07-01 10:51:32
Also in: imx, linux-devicetree, linux-pci, lkml
Subsystem: arm/freescale imx / mxc arm architecture, the rest · Maintainers: Frank Li, Sascha Hauer, Linus Torvalds

From: Sherry Sun <redacted>

Move the power supply properties from the PCIe controller nodes to the
Root Port child nodes to support the new PCI pwrctrl framework.

Since i.MX95 is the new platform that under development phase, it should
be fine to simply move the power supply properties.

Signed-off-by: Sherry Sun <redacted>
---
 arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts | 4 ++--
 arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts | 8 ++++----
 2 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts b/arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts
index 7d820a0f80b2..6aedcbbe915a 100644
--- a/arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts

@@ -555,8 +555,6 @@ &pcie0 {
 	pinctrl-names = "default";
 	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&gpio5 13 GPIO_ACTIVE_LOW>;
-	vpcie-supply = <&reg_m2_pwr>;
-	vpcie3v3aux-supply = <&reg_m2_pwr>;
 	supports-clkreq;
 	status = "disabled";
 };

@@ -570,6 +568,8 @@ &pcie0_ep {
 
 &pcie0_port0 {
 	reset-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	vpcie3v3-supply = <&reg_m2_pwr>;
+	vpcie3v3aux-supply = <&reg_m2_pwr>;
 };
 
 &sai1 {

diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
index 2e463bc7c601..340ab0253ec2 100644
--- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts

@@ -542,8 +542,6 @@ &pcie0 {
 	pinctrl-names = "default";
 	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&i2c7_pcal6524 5 GPIO_ACTIVE_LOW>;
-	vpcie-supply = <&reg_pcie0>;
-	vpcie3v3aux-supply = <&reg_pcie0>;
 	supports-clkreq;
 	status = "okay";
 };

@@ -557,6 +555,8 @@ &pcie0_ep {
 
 &pcie0_port0 {
 	reset-gpios = <&i2c7_pcal6524 5 GPIO_ACTIVE_LOW>;
+	vpcie3v3-supply = <&reg_pcie0>;
+	vpcie3v3aux-supply = <&reg_pcie0>;
 };
 
 &pcie1 {

@@ -564,8 +564,6 @@ &pcie1 {
 	pinctrl-names = "default";
 	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&i2c7_pcal6524 16 GPIO_ACTIVE_LOW>;
-	vpcie-supply = <&reg_slot_pwr>;
-	vpcie3v3aux-supply = <&reg_slot_pwr>;
 	status = "okay";
 };

@@ -578,6 +576,8 @@ &pcie1_ep {
 
 &pcie1_port0 {
 	reset-gpios = <&i2c7_pcal6524 16 GPIO_ACTIVE_LOW>;
+	vpcie3v3-supply = <&reg_slot_pwr>;
+	vpcie3v3aux-supply = <&reg_slot_pwr>;
 };
 
 &sai1 {

-- 
2.50.1

`h`	back out one level
`j`	next message in thread
`k`	previous message in thread
`l`	drill in
`Esc`	close help / fold thread tree
`?`	toggle this help