Hi folks,

I was looking through the RGMII delay setup logic found in
rk_gmac_powerup() of dwmac-rk.c, and found its behavior is strange,

	switch (bsp_priv->phy_iface) {
	case PHY_INTERFACE_MODE_RGMII:
		dev_info(dev, "init for RGMII\n");
		if (bsp_priv->ops->set_to_rgmii)
			bsp_priv->ops->set_to_rgmii(bsp_priv,
						    bsp_priv->tx_delay,
						    bsp_priv->rx_delay);
		break;
	case PHY_INTERFACE_MODE_RGMII_ID:
		dev_info(dev, "init for RGMII_ID\n");
		if (bsp_priv->ops->set_to_rgmii)
			bsp_priv->ops->set_to_rgmii(bsp_priv, 0, 0);
		break;
	case PHY_INTERFACE_MODE_RGMII_RXID:
		dev_info(dev, "init for RGMII_RXID\n");
		if (bsp_priv->ops->set_to_rgmii)
			bsp_priv->ops->set_to_rgmii(bsp_priv,
						    bsp_priv->tx_delay, 0);
		break;
	case PHY_INTERFACE_MODE_RGMII_TXID:
		dev_info(dev, "init for RGMII_TXID\n");
		if (bsp_priv->ops->set_to_rgmii)
			bsp_priv->ops->set_to_rgmii(bsp_priv,
						    0, bsp_priv->rx_delay);
		break;
	case PHY_INTERFACE_MODE_RMII:
		dev_info(dev, "init for RMII\n");
		if (bsp_priv->ops->set_to_rmii)
			bsp_priv->ops->set_to_rmii(bsp_priv);
		break;
	default:
		dev_err(dev, "NO interface defined!\n");
	}

I don't think dwmac-rk.c does any fixup for phy_interface, so the MAC
driver always connects the PHY with unmodified phy-mode.

ethernet-controller.yaml states,

# Device Tree describes hardware, and in this case, it describes the
# PCB between the MAC and the PHY, if the PCB implements delays or
# not.

So let's assume this is true for Rockchip's DWMAC glue, then the
driver's behavior could be summarized as,

phy-mode	PCB delay	Rockchip MAC delay	PHY delay[1]
rgmii		TX & RX		TX & RX			TX & RX
rgmii-id	None		None			TX & RX
rgmii-rxid	TX		TX			RX
rgmii-txid	RX		RX			TX
[1]: if available

where only the "rgmii-id" case makes sense. Other cases come with 2ns
delays added more than once, and would cause broken link.

It looks like dwmac-rk.c considers "phy-mode" to represent MAC's delay
configuration. If so, the table would look like,

phy-mode	PCB delay	Rockchip MAC delay	PHY delay[1]
rgmii		N/A		TX & RX			None
rgmii-id	N/A		None			TX & RX
rgmii-txid	N/A		TX			RX
rgmii-rxid	N/A		RX			TX

all cases have the necessary 2ns delay provided for both TX and RX
signals, however on-PCB delays made by traces couldn't be described
at all. This idea is also proved by comments in Rockchip devicetrees,
for example, rk3576-roc-pc.dts,

	&gmac0 {
		...
		/* Use rgmii-rxid mode to disable rx delay inside Soc */
		phy-mode = "rgmii-rxid";
	};

It seems for Rockchip DWMAC driver, "phy-mode" doesn't follow the
generic definition. Should we annotate in rockchip-dwmac.yaml to mention
the different usage of the property, or update both the driver and
devicetrees to align with ethernet-controller.yaml? The later would
break compatibility with existing devicetrees since there are already 15
instances of "rgmii-rxid" found in arch/arm64/boot/dts/rockchip, but
luckily most boards make use of "rgmii-id".

I only did a brief search in lore but find no related discussion, please
point out if there has already been messages around it, thanks.

Best regards,
Yao Zi