@@ -0,0 +1,100 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright 2025 Bootlin
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tilcdc/ti,am33xx-tilcdc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI LCD Controller, found on AM335x, DA850, AM18x and OMAP-L138
+
+maintainers:
+  - Kory Maincent <kory.maincent@bootlin.com>
+
+properties:
+  compatible:
+    enum:
+      - ti,am33xx-tilcdc
+      - ti,da850-tilcdc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/properties/port
+
+  ti,hwmods:
+    $ref: /schemas/types.yaml#/definitions/string
+    description:
+      Name of the hwmod associated to the LCDC
+
+  max-bandwidth:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      The maximum pixels per second that the memory interface / lcd
+      controller combination can sustain
+    # maximum: 2048*2048*60
+    maximum: 251658240
+
+  max-width:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      The maximum horizontal pixel width supported by the lcd controller.
+    maximum: 2048
+
+  max-pixelclock:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      The maximum pixel clock that can be supported by the lcd controller
+      in KHz.
+
+  blue-and-red-wiring:
+    enum: [straight, crossed]
+    description:
+      This property deals with the LCDC revision 2 (found on AM335x)
+      color errata [1].
+       - "straight" indicates normal wiring that supports RGB565,
+         BGR888, and XBGR8888 color formats.
+       - "crossed" indicates wiring that has blue and red wires
+         crossed. This setup supports BGR565, RGB888 and XRGB8888
+         formats.
+       - If the property is not present or its value is not recognized
+         the legacy mode is assumed. This configuration supports RGB565,
+         RGB888 and XRGB8888 formats. However, depending on wiring, the red
+         and blue colors are swapped in either 16 or 24-bit color modes.
+
+       [1] There is an errata about AM335x color wiring. For 16-bit color
+       mode the wires work as they should (LCD_DATA[0:4] is for Blue[3:7]),
+       but for 24 bit color modes the wiring of blue and red components is
+       crossed and LCD_DATA[0:4] is for Red[3:7] and LCD_DATA[11:15] is
+       for Blue[3-7]. For more details see section 3.1.1 in AM335x
+       Silicon Errata
+       https://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360
+
+required:
+  - compatible
+  - interrupts
+  - reg
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    display-controller@4830e000 {
+        compatible = "ti,am33xx-tilcdc";
+        reg = <0x4830e000 0x1000>;
+        interrupt-parent = <&intc>;
+        interrupts = <36>;
+        ti,hwmods = "lcdc";
+
+        blue-and-red-wiring = "crossed";
+
+        port {
+            endpoint {
+                remote-endpoint = <&hdmi_0>;
+            };
+        };
+    };

@@ -1,82 +0,0 @@
-Device-Tree bindings for tilcdc DRM driver
-
-Required properties:
- - compatible: value should be one of the following:
-    - "ti,am33xx-tilcdc" for AM335x based boards
-    - "ti,da850-tilcdc" for DA850/AM18x/OMAP-L138 based boards
- - interrupts: the interrupt number
- - reg: base address and size of the LCDC device
-
-Recommended properties:
- - ti,hwmods: Name of the hwmod associated to the LCDC
-
-Optional properties:
- - max-bandwidth: The maximum pixels per second that the memory
-   interface / lcd controller combination can sustain
- - max-width: The maximum horizontal pixel width supported by
-   the lcd controller.
- - max-pixelclock: The maximum pixel clock that can be supported
-   by the lcd controller in KHz.
- - blue-and-red-wiring: Recognized values "straight" or "crossed".
-   This property deals with the LCDC revision 2 (found on AM335x)
-   color errata [1].
-    - "straight" indicates normal wiring that supports RGB565,
-      BGR888, and XBGR8888 color formats.
-    - "crossed" indicates wiring that has blue and red wires
-      crossed. This setup supports BGR565, RGB888 and XRGB8888
-      formats.
-    - If the property is not present or its value is not recognized
-      the legacy mode is assumed. This configuration supports RGB565,
-      RGB888 and XRGB8888 formats. However, depending on wiring, the red
-      and blue colors are swapped in either 16 or 24-bit color modes.
-
-Optional nodes:
-
- - port/ports: to describe a connection to an external encoder. The
-   binding follows Documentation/devicetree/bindings/graph.txt and
-   supports a single port with a single endpoint.
-
- - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and
-   Documentation/devicetree/bindings/display/bridge/ti,tfp410.yaml for connecting
-   tfp410 DVI encoder or lcd panel to lcdc
-
-[1] There is an errata about AM335x color wiring. For 16-bit color mode
-    the wires work as they should (LCD_DATA[0:4] is for Blue[3:7]),
-    but for 24 bit color modes the wiring of blue and red components is
-    crossed and LCD_DATA[0:4] is for Red[3:7] and LCD_DATA[11:15] is
-    for Blue[3-7]. For more details see section 3.1.1 in AM335x
-    Silicon Errata:
-    https://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360
-
-Example:
-
-	fb: fb@4830e000 {
-		compatible = "ti,am33xx-tilcdc", "ti,da850-tilcdc";
-		reg = <0x4830e000 0x1000>;
-		interrupt-parent = <&intc>;
-		interrupts = <36>;
-		ti,hwmods = "lcdc";
-
-		blue-and-red-wiring = "crossed";
-
-		port {
-			lcdc_0: endpoint {
-				remote-endpoint = <&hdmi_0>;
-			};
-		};
-	};
-
-	tda19988: tda19988 {
-		compatible = "nxp,tda998x";
-		reg = <0x70>;
-
-		pinctrl-names = "default", "off";
-		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
-		pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
-
-		port {
-			hdmi_0: endpoint {
-				remote-endpoint = <&lcdc_0>;
-			};
-		};
-	};