From: Nihal Kumar Gupta <redacted>

Monaco EVK is a single-board computer based on the Qualcomm QCS8300 SoC.
It lacks a camera sensor in its default configuration.
This series adds CCI support and enables the IMX577 sensor via CSIPHY1
through device tree overlay.

We have tested IMX577 Sensor on CCI1 with following commands:
- media-ctl --reset
- media-ctl -V '"imx577 3-001a":0[fmt:SRGGB10/4056x3040 field:none]'
- media-ctl -V '"msm_csiphy1":0[fmt:SRGGB10/4056x3040]'
- media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4056x3040]'
- media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4056x3040]'
- media-ctl -l '"msm_csiphy1":1->"msm_csid0":0[1]'
- media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
- yavta -B capture-mplane -c -I -n 5 -f SRGGB10P -s 4056x3040 -F /dev/video1
---

This patch series depends on patch series:
https://lore.kernel.org/all/20251107162521.511536-1-quic_vikramsa@quicinc.com (local)

Bindings for Supplies are added by below patch:
https://lore.kernel.org/all/20251107162521.511536-1-quic_vikramsa@quicinc.com (local)

Changes in v5:
- Rename cciX_i2cY_* to cciX_Y_* to shorten the labels - Vladimir 
- Added description of pins with MCLK function - Vladimir 
- Link to v4:
  https://lore.kernel.org/all/20251015131303.2797800-1-quic_vikramsa@quicinc.com (local)

Changes in v4:
- Remove the AXI source clock from the CCI node - Konrad
- Updated the qcs8300-camss device tree binding.
- Link to v3:
  https://lore.kernel.org/all/20250917130647.1701883-1-quic_vikramsa@quicinc.com (local)

Changes in v3:
- Updated and Wrapped commit messages for [PATCH v2 1/3] and [PATCH v2 2/3] - Rob
- Link to v2:
  https://lore.kernel.org/all/20250912141134.2799078-1-quic_vikramsa@quicinc.com (local)

Changes in v2:
- Remove the patch that adds PHY supply documentation in the qcs8300 CAMSS. 
  bindings. This change should be submitted together with the qcs8300 bindings patch.
- Fix indentation and regulator node name - Krzysztof.
- Update commit message as suggested - Dmitry.
- Link to v1:
  https://lore.kernel.org/lkml/20250909114241.840842-1-quic_vikramsa@quicinc.com (local)

Used following tools for the sanity check of these changes.
- make -j32 W=1
- checkpatch.pl
- make DT_CHECKER_FLAGS=-m W=1 DT_SCHEMA_FILES=i2c/qcom,i2c-cci.yaml dt_binding_check
- make CHECK_DTBS=y W=1 DT_SCHEMA_FILES=i2c/qcom,i2c-cci.yaml
- make DT_CHECKER_FLAGS=-m W=1 DT_SCHEMA_FILES=media/qcom,qcs8300-camss.yaml dt_binding_check
- make CHECK_DTBS=y W=1 DT_SCHEMA_FILES=media/qcom,qcs8300-camss.yaml

Signed-off-by: Nihal Kumar Gupta <redacted>
Signed-off-by: Vikram Sharma <redacted>

Nihal Kumar Gupta (3):
  dt-bindings: i2c: qcom-cci: Document qcs8300 compatible
  arm64: dts: qcom: qcs8300: Add CCI definitions
  arm64: dts: qcom: monaco-evk-camera: Add DT overlay

 .../devicetree/bindings/i2c/qcom,i2c-cci.yaml |   2 +
 arch/arm64/boot/dts/qcom/Makefile             |   4 +
 .../dts/qcom/monaco-evk-camera-imx577.dtso    | 105 ++++++
 arch/arm64/boot/dts/qcom/monaco.dtsi          | 303 ++++++++++++++++++
 4 files changed, 414 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/monaco-evk-camera-imx577.dtso

-- 
2.34.1