On Fri, Jul 18, 2025 at 04:11:18PM -0700, Donald Shannon wrote:

+
+/ {
+	model = "AST2600 GB200 UT3.0b BMC";
+	compatible = "nvidia,gb200-ut30b", "aspeed,ast2600";
+
+	aliases {
+		serial2 = &uart3;
+		serial4 = &uart5;
+		i2c16   = &imux16;
+		i2c17   = &imux17;
+		i2c18   = &imux18;
+		i2c19   = &imux19;
+		i2c20   = &imux20;
+		i2c21   = &imux21;
+		i2c22   = &imux22;
+		i2c23   = &imux23;
+		i2c24   = &imux24;
+		i2c25   = &imux25;
+		i2c26   = &imux26;
+		i2c27   = &imux27;
+		i2c28   = &imux28;
+		i2c29   = &imux29;
+		i2c30   = &imux30;
+		i2c31   = &imux31;
+		i2c32   = &imux32;
+		i2c33   = &imux33;
+		i2c34   = &imux34;
+		i2c35   = &imux35;
+		i2c36   = &imux36;
+		i2c37   = &imux37;
+		i2c38   = &imux38;
+		i2c39   = &imux39;
+		i2c40	= &e1si2c0;
+		i2c41	= &e1si2c1;
+		i2c42	= &e1si2c2;
+		i2c43	= &e1si2c3;
+		i2c48	= &i2c17mux0;
+		i2c49	= &i2c17mux1;
+		i2c50	= &i2c17mux2;
+		i2c51	= &i2c17mux3;
+		i2c52	= &i2c25mux0;
+		i2c53	= &i2c25mux1;
+		i2c54	= &i2c25mux2;
+		i2c55	= &i2c25mux3;
+		i2c56	= &i2c29mux0;
+		i2c57	= &i2c29mux1;
+		i2c58	= &i2c29mux2;
+		i2c59	= &i2c29mux3;
+	};
+
+	buttons {
+		button-power {
+			label = "power-btn";

How is this supposed to work? How does anything bind here?

+			gpio = <&sgpiom0 156 GPIO_ACTIVE_LOW>;
+		};
+		button-uid {
+			label = "uid-btn";
+			gpio = <&sgpiom0 154 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "uid_led";
+			gpios = <&sgpiom0 27 GPIO_ACTIVE_LOW>;
+		};
+		led-1 {
+			label = "fault_led";
+			gpios = <&sgpiom0 29 GPIO_ACTIVE_LOW>;
+		};
+		led-2 {
+			label = "power_led";
+			gpios = <&sgpiom0 31 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reg_3v3_stby: regulator-3v3-standby {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3-standby";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio0 ASPEED_GPIO(M, 3) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
+		ramoops@a0000000 {
+			compatible = "ramoops";
+			reg = <0xa0000000 0x100000>; /* 1MB */
+			record-size = <0x10000>; /* 64KB */
+			max-reason = <2>; /* KMSG_DUMP_OOPS */
+		};
+
+		gfx_memory: framebuffer {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+		};
+
+		video_engine_memory: jpegbuffer {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+		};
+	};
+};
+
+// Enable Primary flash on FMC for bring up activity
+&fmc {
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+		status = "okay";

Why do you need it? Anything disabled it?

Best regards,
Krzysztof