On 07/10/2024 17:02, Dario Binacchi wrote:

On Sun, Oct 6, 2024 at 3:13 PM Krzysztof Kozlowski [off-list ref] wrote:

quoted

On 05/10/2024 10:57, Dario Binacchi wrote:

quoted

On Thu, Oct 3, 2024 at 12:46 PM Krzysztof Kozlowski [off-list ref] wrote:

quoted

On 01/10/2024 08:29, Dario Binacchi wrote:

quoted

On Mon, Sep 30, 2024 at 8:45 AM Krzysztof Kozlowski [off-list ref] wrote:

quoted

On 29/09/2024 22:00, Dario Binacchi wrote:

quoted

quoted

quoted

+  properties:
+    compatible:
+      contains:
+        enum:
+          - fsl,imx8mm-anatop
+
+then:
+  properties:
+    fsl,ssc-clocks:

Nope. Properties must be defined in top-level.

quoted

+      $ref: /schemas/types.yaml#/definitions/phandle-array
+      description:
+        The phandles to the PLLs with spread spectrum clock generation
+        hardware capability.

These should be clocks.

Sorry, but I can't understand what you're asking me.
Could you kindly explain it to me in more detail?

You added new property instead of using existing one for this purpose:
'clocks'.

quoted

Best regards,
Krzysztof

I added this new property specifically for managing spread-spectrum.
Indeed, not all clocks/PLLs
managed by the node/peripheral support spread-spectrum, and the added
properties specify
parameters for enabling and tuning SSC for each individual PLL based
on the index of each list.
If I were to use the 'clocks' property and add a clock to this list
that does not support SSC, IMHO
the pairings would be less clear.

You duplicate property with argument "pairings shall match". Well, I am
not happy with the duplication. Clocks have specific order, thus it is
explicit which one needs tuning. Your other properties can match them as
well, just index from clocks is offset...

Just to check if I understood correctly what you are suggesting before
submitting version 3 of the patch.
Something, for example, like:

clocks = <&clk, IMX8MP_AUDIO_PLL1>,  <&clk, IMX8MP_AUDIO_PLL2>, <&clk
IMX8MP_VIDEO_PLL1>;
fsl,ssc-modfreq-hz = <0, 3517>, <2, 6818>;

Hm, what is 0? If clock index, then no, it's redundant. The first item
in cannot point to other clock.

Also, what exactly are you setting here

I am enabling and configuring the spread spectrum.

Normal clock: Without spread spectrum, the clock signal has a fixed and
repetitive frequency (e.g., 100 MHz). This frequency generates an
electromagnetic
signal concentrated on a single frequency, and if strong enough, it can disturb
other devices.

Spread spectrum:  With spread spectrum, the clock frequency is
slightly "modulated,"
meaning it oscillates around a central value. For example, if the base
frequency is 100 MHz,
the clock might vary between 99.5 MHz and 100.5 MHz in a cyclic manner. This
small variation spreads the energy over a wider range of frequencies
(from 99.5 to 100.5 MHz),
reducing the intensity of the signal at any one frequency.

Sure, so each board will come with its own, different values and you
will not put into the SoC DTSI?

Where is the DTS? I received only this patch.

quoted

and why assigned-clock-rates are
not working?

The traditional clock properties, such as clocks,
assigned-clocks-rates, etc retain their usual
meaning even when spread spectrum is applied. However, to implement
the spread spectrum
mechanism in a circuit with a PLL (Phase-Locked Loop), additional
specific parameters are
introduced to properly configure the frequency modulation:

 - Modulation frequency: i. e. fsl,ssc-modfreq-hz
 - Modulation rate: i.e.  fsl,ssc-modrate-percent
 - Modulation type:  i. e. fsl,ssc-modmethod (center-spread, down-spread)

Additionally, it should be noted that not all anatop PLLs are equipped
with circuitry for spread
spectrum, but only a small subset of them. This is the reason why I
introduced the property
"fsl, ssc-clocks".

This is another commit [1] on enabling spread spectrum that I
implemented some time ago for
the am335x. The most evident difference is that in that case the node
was a clock node and not
a clock controller, as in the case of anatop. The parameters are also
not exactly the same, but
that depends on the platform.

[1] 4a8bc2644ef0cbf8e ("dt-bindings: ti: dpll: add spread spectrum support")

OK, I still do not know what "0" was, but the items are fixed, so you
know exactly which clock you are configuring here.

Best regards,
Krzysztof