Re: resctrl2 - status

On Fri, 25 Aug 2023 13:20:22 -0700
Reinette Chatre [off-list ref] wrote:

Hi Tony,

On 8/25/2023 12:44 PM, Luck, Tony wrote:

quoted

quoted

quoted

quoted

Alternatively, can user space just take a "load all resctrl modules
and see what sticks" (even modules of different architectures since
a user space may want to be generic) approach?  

This mostly works. Except for the cases where different modules access
the same underlying hardware, so can't be loaded together.

Examples:

rdt_l3_cat vs. rdt_l3_cdp - user needs to decide whether they want CDP or not.
But this is already true ... they have to decide whether to pass the "-o cdp" option
to mount.

rdt_l3_mba vs. rdt_l3_mba_MBps - does the user want to control memory bandwidth
with percentages, or with MB/sec values. Again the user already has to make this
decision when choosing mount options.


Maybe the "What resctrl options does this machine support?" question would be
best answered with a small utility?  

A user space utility or a kernel provided utility? If it is a user space utility
I think it would end up needing to duplicate what the kernel is required to do
to know if a particular feature is supported. It seems appropriate that this
could be a kernel utility that can share this existing information with user
space. resctrl already supports the interface for this via /sys/fs/resctrl/info.  

I was imagining a user space utility. Even though /proc/cpuinfo doesn't show
all features, a utility has access to all the CPUID leaves that contain the
details of each feature enumeration.  

For x86 that may work (in some scenarios, see later) for now but as I understand
Arm would need a different solution where I believe the information is obtained
via ACPI. I think it is unnecessary to require user space to have parsers for
CPUID and ACPI if that same information needs to be parsed by the kernel and
there already exists an interface with which the information is communicated
from kernel to user space. Also, just because information CPUID shows a feature
is supported by the hardware does not mean that the kernel has support for that
feature. This could be because of a feature mismatch between user space and
kernel, or even some features disabled for use via the, for example "rdt=!l3cat",
kernel parameter.

James probably also has views on this, but I wouldn't expect userspace to go anywhere
near ACPI parsing. If the description of what MPAM features are supported (before
resctrl is running) is necessary, then we should add it to the existing
description of the various caches etc.  Maybe somewhere in
/sys/bus/node/devices/nodeX/cpuY/cache/indexZ/
for the caches and
/sys/bus/node/devices/nodeX for the DRAM controllers.

I'm sure we can find somewhere sensible for other things covered by MPAM.
The MPAM table parsers and some early code to query features from the hardware should
be able to figure out what is needed.

Perhaps x86 systems could provide similar descriptions but originating from CPUID etc.

Jonathan

quoted

quoted

fyi ... as with previous attempts to discuss this work I find it difficult
to discuss this work when you are selective about what you want to discuss/answer
and just wipe the rest. Through this I understand that I am not your target
audience.  

Not my intent. I value your input highly. I'm maybe too avid a follower of the
"trim your replies" school of e-mail etiquette. I thought I'd covered the gist
of your message.

I'll try to be more thorough in responding in the future.  

Two items from my previous email remain open:

First, why does making the code modular require everything to be loadable
modules?
I think that it is great that the code is modular. Ideally it will help to
support the other architectures. As you explain this modular design also
has the benefit that "modules" can be loaded and unloaded after resctrl mount.
Considering your example of MBA and MBA_MBps support ... if I understand
correctly with code being modular it enables changes from one to the other
after resctrl mount. User can start with MBA and then switch to MBA_MBps
without needing to unmount resctrl. What I do not understand is why does
the code being modular require everything to be modules? Why, for example,
could a user not interact with a resctrl file that enables the user to make
this switch from, for example, MBA to MBA_MBps? With this the existing
interfaces can remain to be respected, the existing mount parameters need
to remain anyway, while enabling future "more modular" usages.

Second, copied from my previous email, what is the plan to deal with current
users that just mount resctrl and expect to learn from it what features are
supported?

Reinette

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel