1. This patch adds pinctrl file for mt8186.
2. This patch adds mt8186 compatible node in binding document.

Signed-off-by: Guodong Liu <redacted>
---
 .../bindings/pinctrl/pinctrl-mt8186.yaml      |  303 +++++
 include/dt-bindings/pinctrl/mt8186-pinfunc.h  | 1174 +++++++++++++++++
 2 files changed, 1477 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-mt8186.yaml
 create mode 100644 include/dt-bindings/pinctrl/mt8186-pinfunc.h

diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8186.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8186.yaml
new file mode 100644
index 000000000000..0a1154faca29
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8186.yaml

@@ -0,0 +1,303 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/pinctrl-mt8186.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek MT8186 Pin Controller
+
+maintainers:
+  - Sean Wang <sean.wang@mediatek.com>
+
+description: |
+  The Mediatek's Pin controller is used to control SoC pins.
+
+properties:
+  compatible:
+    const: mediatek,mt8186-pinctrl
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    description: |
+      Number of cells in GPIO specifier. Since the generic GPIO binding is used,
+      the amount of cells must be specified as 2. See the below
+      mentioned gpio binding representation for description of particular cells.
+    const: 2
+
+  gpio-ranges:
+    description: gpio valid number range.
+    maxItems: 1
+
+  reg:
+    description: |
+      Physical address base for gpio base registers. There are 8 GPIO
+      physical address base in mt8186.
+    maxItems: 8

+
+              An example of using RSEL define:
+              pincontroller {
+                i2c0_pin {
+                  pins {
+                    pinmux = <PINMUX_GPIO128__FUNC_SDA0>;
+                    bias-pull-down = <MTK_PULL_SET_RSEL_001>;
+                  }
+                };
+              };
+              An example of using si unit resistance value(ohm):
+              &pio {
+                mediatek,rsel_resistance_in_si_unit;
+              }
+              pincontroller {
+                i2c0_pin {
+                  pins {
+                    pinmux = <PINMUX_GPIO128__FUNC_SDA0>;
+                    bias-pull-down = <75000>;
+                  }
+                };
+              };
+
+          bias-pull-up:
+            description: |
+              For pull up type is normal, it don't need add RSEL & R1R0 define
+              and resistance value.
+              For pull up type is PUPD/R0/R1 type, it can add R1R0 define to
+              set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
+              "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
+              "MTK_PUPD_SET_R1R0_11" define in mt8186.
+              For pull up type is RSEL, it can add RSEL define & resistance
+              value(ohm) to set different resistance by identifying property
+              "mediatek,rsel_resistance_in_si_unit".
+              It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
+              & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011"
+              & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101"
+              & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
+              define in mt8186. It can also support resistance value(ohm)
+              "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" &
+              "75000" in mt8186.
+              oneOf:
+                - enum: [100, 101, 102, 103]
+                - description: mt8186 pull up PUPD/R0/R1 type define value.
+                - enum: [200, 201, 202, 203, 204, 205, 206, 207]
+                - description: mt8186 pull up RSEL type define value.
+                - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000]
+                - description: mt8186 pull up RSEL type si unit value(ohm).
+              An example of using RSEL define:
+              pincontroller {
+                i2c0-pins {
+                  pins {
+                    pinmux = <PINMUX_GPIO128__FUNC_SDA0>;
+                    bias-pull-up = <MTK_PULL_SET_RSEL_001>;
+                  }
+                };
+              };
+              An example of using si unit resistance value(ohm):
+              &pio {
+                mediatek,rsel_resistance_in_si_unit;
+              }
+              pincontroller {
+                i2c0-pins {
+                  pins {
+                    pinmux = <PINMUX_GPIO128__FUNC_SDA0>;
+                    bias-pull-up = <1000>;
+                  }
+                };
+              };
+
+          bias-disable: true
+
+          output-high: true
+
+          output-low: true
+
+          input-enable: true
+
+          input-disable: true
+
+          input-schmitt-enable: true
+
+          input-schmitt-disable: true
+
+        required:
+          - pinmux
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-controller
+  - '#interrupt-cells'
+  - gpio-controller
+  - '#gpio-cells'
+  - gpio-ranges
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/pinctrl/mt8186-pinfunc.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    pio: pinctrl@10005000 {
+      compatible = "mediatek,mt8186-pinctrl";
+      reg = <0x10005000 0x1000>,
+            <0x10002000 0x0200>,
+            <0x10002200 0x0200>,
+            <0x10002400 0x0200>,
+            <0x10002600 0x0200>,
+            <0x10002A00 0x0200>,
+            <0x10002c00 0x0200>,
+            <0x1000b000 0x1000>;
+      reg-names = "iocfg0", "iocfg_bm", "iocfg_bl",
+                  "iocfg_br", "iocfg_lm", "iocfg_rb",
+                  "iocfg_tl", "eint";
+      gpio-controller;
+      #gpio-cells = <2>;
+      gpio-ranges = <&pio 0 0 185>;
+      interrupt-controller;
+      interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH 0>;
+      #interrupt-cells = <2>;
+
+      pio-pins {
+        pins {
+          pinmux = <PINMUX_GPIO0__FUNC_GPIO0>;
+          output-low;
+        };
+      };
+
+      spi0-pins {
+        pins-spi {
+          pinmux = <PINMUX_GPIO0__FUNC_SPI0_CLK_B>,
+                   <PINMUX_GPIO1__FUNC_SPI0_CSB_B>,
+                   <PINMUX_GPIO2__FUNC_SPI0_MO_B>;
+          bias-disable;
+        };
+        pins-spi-mi {
+          pinmux = <PINMUX_GPIO3__FUNC_SPI0_MI_B>;
+          bias-pull-down;
+        };
+      };
+
+      i2c0-pins {
+        pins {
+          pinmux = <PINMUX_GPIO127__FUNC_SCL0>,
+                   <PINMUX_GPIO128__FUNC_SDA0>;
+          bias-disable;
+          mediatek,drive-strength-adv = <7>;
+        };
+      };
+    };

diff --git a/include/dt-bindings/pinctrl/mt8186-pinfunc.h b/include/dt-bindings/pinctrl/mt8186-pinfunc.h
new file mode 100644
index 000000000000..f58983d11bca
--- /dev/null
+++ b/include/dt-bindings/pinctrl/mt8186-pinfunc.h

@@ -0,0 +1,1174 @@
+/* SPDX-License-Identifier: GPL-2.0 */