[RFC PATCH 0/3] Add support for BCM2835 camera interface (unicam)
From: Jean-Michel Hautbois <hidden>
Date: 2022-01-12 17:27:53
Also in:
linux-devicetree, linux-media, lkml
Hello ! This patch series adds the BCM2835 CCP2/CSI2 camera interface named unicam. This driver is already used in the out-of-tree linux-rpi repository [1], and this work aims to support it in mainline. The series is based on top of: - Rebased on top of 5.16 Tomi Valkeinen's multiplexed stream work, on his multistream/work branch [2] which has been submitted as v10 at the time of this writing. The objective is to demonstrate the use of multiplexed streams on a real world widely used example as well as supporting unicam mainline. - "Add 12bit and 14bit luma-only formats" series [3]. The series is made of 4 patches: - 2/3 introduces dt-bindings documentation and MAINTAINERS entry I have tentatively assigned maintainership, is this fine ? - 2/3 adds the driver support in media/platform - 3/3 modifies imx219 driver to make it use the multiplexed streams API All those patches are in my tree [4]. Patch 2/3 comes from the linux-rpi work [1] with substantial modifications: - Removed the non-mc API which is deprecated, and not needed upstream - Moved from one video node with two source pads (image and embedded) to two video nodes - Added a subdev between the sensor and the video nodes to properly route the streams - Added support for multiplexed streams API In order to test it, one will need a RPi board and the camv2 (imx219) sensor. An updated v4l-utils is also needed [5] to have support for multiplexed streams. v4l2-compliance passes on both video devices, without streaming testing though. The downstream DTB's and overlays are used from the existing Raspberry Pi OS for testing, and this series does not yet integrate the device tree nodes into the upstream BCM2835 or BCM2711 device tree support. The media-ctl topology is:
pi@raspberrypi:~ $ media-ctl -d0 -p
Media controller API version 5.16.0
Media device information
------------------------
driver unicam
model unicam
serial
bus info platform:fe801000.csi
hw revision 0x0
driver version 5.16.0
Device topology
- entity 1: unicam-subdev (3 pads, 3 links, 1 route)
type V4L2 subdev subtype Unknown flags 0
device node name /dev/v4l-subdev0
routes:
0/0 -> 1/0 [ACTIVE]
pad0: Sink
[stream:0 fmt:UYVY8_2X8/640x480 field:none colorspace:srgb xfer:srgb ycbcr:601 quantization:lim-range]
<- "imx219 10-0010":0 [ENABLED,IMMUTABLE]
pad1: Source
[stream:0 fmt:UYVY8_2X8/640x480 field:none colorspace:srgb xfer:srgb ycbcr:601 quantization:lim-range]
-> "unicam-image":0 [ENABLED,IMMUTABLE]
pad2: Source
-> "unicam-embedded":0 [ENABLED,IMMUTABLE]
- entity 5: imx219 10-0010 (1 pad, 1 link, 2 routes)
type V4L2 subdev subtype Sensor flags 0
device node name /dev/v4l-subdev1
routes:
0/0 -> 0/0 [ACTIVE, IMMUTABLE, SOURCE]
0/0 -> 0/1 [ACTIVE, SOURCE]
pad0: Source
[stream:0 fmt:SRGGB10_1X10/3280x2464 field:none colorspace:raw
crop.bounds:(8,8)/3280x2464
crop:(8,8)/3280x2464]
[stream:1 fmt:METADATA_8/16384x1 field:none
crop.bounds:(8,8)/3280x2464
crop:(8,8)/3280x2464]
-> "unicam-subdev":0 [ENABLED,IMMUTABLE]
- entity 7: unicam-image (1 pad, 1 link, 0 route)
type Node subtype V4L flags 1
device node name /dev/video0
pad0: Sink
<- "unicam-subdev":1 [ENABLED,IMMUTABLE]
- entity 13: unicam-embedded (1 pad, 1 link, 0 route)
type Node subtype V4L flags 0
device node name /dev/video1
pad0: Sink
<- "unicam-subdev":2 [ENABLED,IMMUTABLE]
In order to properly configure the media pipeline, it is needed to call
the usual ioctls, and configure routing in order to send the embedded
data from the sensor to the "unicam-embedded" device node :
``` media=0
media-ctl -d${media} -l "'imx219 10-0010':0->'unicam-subdev':0 [1]"
media-ctl -d${media} -l "'unicam-subdev':1->'unicam-image':0 [1]"
media-ctl -d${media} -v -R "'unicam-subdev' [0/0->1/0[1],0/1->2/0[1]]"
media-ctl -d${media} -V "'imx219 10-0010':0/0
[fmt:SRGGB10_1X10/3280x2464 field:none]" v4l2-ctl -d0 --set-fmt-video
width=3280,height=2464,pixelformat='pRAA',field=none media-ctl
-d${media} -v -V "'imx219 10-0010':0/1 [fmt:METADATA_8/16384x1
field:none]" media-ctl -d${media} -p ```
Be sure to configure the routes before setting the format, as s_routing
resets the default format.
Then a frame can be capture with yavta:
`yavta --capture=1 /dev/video0 -F/tmp/test-#.bin`
[1]: https://github.com/raspberrypi/linux/tree/rpi-5.15.y
[2]: https://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux.git/log/?h=multistream/work
[3]: https://patchwork.linuxtv.org/project/linux-media/list/?series=7099
[4]: https://github.com/jhautbois/linux-rpi/tree/jmh/tomba/multistream/work-v10
[5]: https://github.com/tomba/v4l-utils
Jean-Michel Hautbois (3):
media: dt-bindings: media: Add bindings for bcm2835-unicam
media: bcm2835-unicam: Add support for for CCP2/CSI2 camera interface
media: imx219: Add support for multiplexed streams
.../bindings/media/brcm,bcm2835-unicam.yaml | 103 +
MAINTAINERS | 7 +
drivers/media/i2c/imx219.c | 458 +--
drivers/media/platform/Kconfig | 1 +
drivers/media/platform/Makefile | 2 +
drivers/media/platform/bcm2835/Kconfig | 21 +
drivers/media/platform/bcm2835/Makefile | 3 +
.../media/platform/bcm2835/bcm2835-unicam.c | 2694 +++++++++++++++++
.../media/platform/bcm2835/vc4-regs-unicam.h | 253 ++
9 files changed, 3332 insertions(+), 210 deletions(-)
create mode 100644 Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml
create mode 100644 drivers/media/platform/bcm2835/Kconfig
create mode 100644 drivers/media/platform/bcm2835/Makefile
create mode 100644 drivers/media/platform/bcm2835/bcm2835-unicam.c
create mode 100644 drivers/media/platform/bcm2835/vc4-regs-unicam.h
--
2.32.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel