Re: [PATCH v2 1/2] mmc: meson-mx-sdhc: Set MANUAL_STOP for multi-block SDIO commands
From: Ulf Hansson <hidden>
Date: 2021-12-21 13:03:21
Also in:
linux-amlogic, linux-mmc, lkml
On Sun, 19 Dec 2021 at 16:34, Martin Blumenstingl [off-list ref] wrote:
The vendor driver implements special handling for multi-block
SD_IO_RW_EXTENDED (and SD_IO_RW_DIRECT) commands which have data
attached to them. It sets the MANUAL_STOP bit in the MESON_SDHC_MISC
register for these commands. In all other cases this bit is cleared.
Here we omit SD_IO_RW_DIRECT since that command never has any data
attached to it.
This fixes SDIO wifi using the brcmfmac driver which reported the
following error without this change on a Netxeon S82 board using a
Meson8 (S802) SoC:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_sdiod_ramrw: membytes transfer failed
brcmf_sdio_download_code_file: error -110 on writing 219557 membytes
at 0x00000000
brcmf_sdio_download_firmware: dongle image file download failed
And with this change:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may
have limited channels available
brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00
version 5.90.195.89.6 FWID 01-b30a427d
Fixes: e4bf1b0970ef96 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>Applied for fixes and by adding a stable tag, thanks! Kind regards Uffe
quoted hunk ↗ jump to hunk
--- drivers/mmc/host/meson-mx-sdhc-mmc.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)diff --git a/drivers/mmc/host/meson-mx-sdhc-mmc.c b/drivers/mmc/host/meson-mx-sdhc-mmc.c index 7cd9c0ec2fcf..8fdd0bbbfa21 100644 --- a/drivers/mmc/host/meson-mx-sdhc-mmc.c +++ b/drivers/mmc/host/meson-mx-sdhc-mmc.c@@ -135,6 +135,7 @@ static void meson_mx_sdhc_start_cmd(struct mmc_host *mmc, struct mmc_command *cmd) { struct meson_mx_sdhc_host *host = mmc_priv(mmc); + bool manual_stop = false; u32 ictl, send; int pack_len;@@ -172,12 +173,27 @@ static void meson_mx_sdhc_start_cmd(struct mmc_host *mmc, else /* software flush: */ ictl |= MESON_SDHC_ICTL_DATA_XFER_OK; + + /* + * Mimic the logic from the vendor driver where (only) + * SD_IO_RW_EXTENDED commands with more than one block set the + * MESON_SDHC_MISC_MANUAL_STOP bit. This fixes the firmware + * download in the brcmfmac driver for a BCM43362/1 card. + * Without this sdio_memcpy_toio() (with a size of 219557 + * bytes) times out if MESON_SDHC_MISC_MANUAL_STOP is not set. + */ + manual_stop = cmd->data->blocks > 1 && + cmd->opcode == SD_IO_RW_EXTENDED; } else { pack_len = 0; ictl |= MESON_SDHC_ICTL_RESP_OK; } + regmap_update_bits(host->regmap, MESON_SDHC_MISC, + MESON_SDHC_MISC_MANUAL_STOP, + manual_stop ? MESON_SDHC_MISC_MANUAL_STOP : 0); + if (cmd->opcode == MMC_STOP_TRANSMISSION) send |= MESON_SDHC_SEND_DATA_STOP; --2.34.1
_______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel